OK, here's my shot at exhaustive detail, most of which doesn't give me much of
a clue. And not being able to get the digital camera to work as smoothly as
under Win2K sure doesn't help me with convincing the wife Linux is worth
using ... ANY suggestions or pointers would be greatly appreciated.
========== SUMMARY
- Cannot change memory sticks without unloading/reloading usb-storage module
- CAN remove and then reinsert the same memory stick without trouble
- USB device number seems to change each time a stick is inserted,
whether the same stick or a new stick
I'm clueless here ...
========== OVERVIEW
Step 1: Cold boot system--nothing unusual noted
Debugging info included:
dmesg output
syslog output
lsmod output
/proc/bus/usb/devices
lspci output
lspci -v -s 7.2 output
lsusb -v output
Step 2: Results of executing "modprobe usb-storage"
Appears to load fine.
Debugging info included:
dmesg output
syslog entries
lsmod output
Step 3: Results of turning on camera
Appears to go fine, although there are a couple of lines in the dmesg
output that look like errors of some kind? Camera loaded as device #2;
Product string contains several models, but NOT "DSC P5" which this one
is.
Debugging info included:
dmesg--some lines that look like may be errors to me?
usb-storage: Bad LUN (0/1)
and
usb-storage: Bad target number (1/0)
through (7/0)
syslog
/proc/bus/usb/devices
lsusb -v
Step 4: Results of "mount /mnt/camera"
No problems
Debugging info included:
dmesg
syslog
Step 5: Results of "umount /mnt/camera"
Nothing recorded in syslog or dmesg ... mount shows it no longer mounted
Step 6: Results of removing memory stick
Appears to be recognized by kernel; messages appear in dmesg and syslog,
device is removed from /proc/bus/usb/devices and lsusb output. No apparent
error messages.
Debugging info included:
dmesg
syslog
/proc/bus/usb/devices
lsusb -v
Step 7: Results of inserting new chip
//NOTE: Earlier, I did notice that I could remove and reinsert the same
//chip without any apparent problem mounting it again. This is with a
//different chip
Appears to be recognized BUT! Assigned different address: first time was
assigned address 2, now assigned address 3
Debugging info included:
dmesg
syslog
/proc/bus/usb/devices
lsusb -v
Step 8: Results of "mount /mnt/camera"
Error message:
mount: wrong fs type, bad option, bad superblock on /dev/sda1,
or too many mounted file systems
Debugging info included:
dmesg
syslog
Step 9: Results of "rmmod usb-storage"
Appears to unload cleanly; camera still listed in /proc/bus/usb/devices
Debugging info included:
dmesg
syslog
lsmod
/proc/bus/usb/devices
Step 10: Results of "insmod usb-storage"
Appears to go fine, although the same suspicious lines appear in dmesg
that previously appeared when the camera was first turned on (step 3).
Also, now loaded as device #3 vice #2 earlier
Debugging info included:
dmesg
syslog
lsusb -v
Step 11: Results of "mount /mnt/camera"
Works fine ...
========== STEP 1: Freshly booted, normal system
----- dmesg lines related to usb
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 21:03:59 Mar 10 2003
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: USB UHCI at I/O 0x6400, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
usb.c: kmalloc IF cfb614a0, numif 1
usb.c: new device strings: Mfr=0, Product=2, SerialNumber=1
usb.c: USB device number 1 default language ID 0x0
Product: USB UHCI Root Hub
SerialNumber: 6400
hub.c: USB hub found
hub.c: 2 ports detected
hub.c: standalone hub
hub.c: ganged power switching
hub.c: global over-current protection
hub.c: Port indicators are not supported
hub.c: power on to power good time: 2ms
hub.c: hub controller current requirement: 0mA
hub.c: port removable status: RR
hub.c: local power source is good
hub.c: no over-current condition exists
hub.c: enabling power on all ports
usb.c: hub driver claimed interface cfb614a0
usb.c: kusbd: /sbin/hotplug add 1
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
----- syslog entries
Mar 11 20:01:06 mycroft kernel: usb.c: registered new driver usbdevfs
Mar 11 20:01:06 mycroft kernel: usb.c: registered new driver hub
Mar 11 20:01:06 mycroft kernel: usb-uhci.c: $Revision: 1.275 $ time 21:03:59
Mar 10 2003
Mar 11 20:01:06 mycroft kernel: usb-uhci.c: High bandwidth mode enabled
Mar 11 20:01:06 mycroft kernel: usb-uhci.c: USB UHCI at I/O 0x6400, IRQ 11
Mar 11 20:01:06 mycroft kernel: usb-uhci.c: Detected 2 ports
Mar 11 20:01:07 mycroft kernel: usb.c: new USB bus registered, assigned bus
number 1
Mar 11 20:01:07 mycroft kernel: Product: USB UHCI Root Hub
Mar 11 20:01:07 mycroft kernel: SerialNumber: 6400
Mar 11 20:01:07 mycroft kernel: hub.c: USB hub found
Mar 11 20:01:07 mycroft kernel: hub.c: 2 ports detected
----- lsmod output
Module Size Used by
es1370 24944 1 (autoclean)
parport_pc 21696 1 (autoclean)
lp 6624 0 (autoclean)
parport 25120 1 (autoclean) [parport_pc lp]
ide-scsi 7776 0
scsi_mod 85152 1 [ide-scsi]
usb-uhci 21616 0 (unused)
usbcore 63488 1 [usb-uhci]
----- /proc/bus/usb/devices
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.00 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 0.00
S: Product=USB UHCI Root Hub
S: SerialNumber=6400
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=255ms
----- lspci output
00:00.0 Host bridge: Intel Corporation 440BX/ZX - 82443BX/ZX Host bridge (rev
02)
00:01.0 PCI bridge: Intel Corporation 440BX/ZX - 82443BX/ZX AGP bridge (rev
02)
00:07.0 ISA bridge: Intel Corporation 82371AB PIIX4 ISA (rev 02)
00:07.1 IDE interface: Intel Corporation 82371AB PIIX4 IDE (rev 01)
00:07.2 USB Controller: Intel Corporation 82371AB PIIX4 USB (rev 01)
00:07.3 Bridge: Intel Corporation 82371AB PIIX4 ACPI (rev 02)
00:0d.0 Multimedia audio controller: Ensoniq ES1370 [AudioPCI]
00:0f.0 Ethernet controller: Lite-On Communications Inc LNE100TX [Linksys
EtherFast 10/100] (rev 25)
01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G100
[Productiva] AGP (rev 01)
----- lspci -vv -s 7.2 output
00:07.2 USB Controller: Intel Corporation 82371AB PIIX4 USB (rev 01) (prog-if
00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at 6400 [size=32]
----- lsusb -v output
Unknown line at line 1809
Duplicate HUT Usage Spec at line 2650
Bus 001 Device 001: ID 0000:0000 Virtual Hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.00
bDeviceClass 9 Hub
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x0000 Virtual
idProduct 0x0000 Hub
bcdDevice 0.00
iManufacturer 0
iProduct 2 USB UHCI Root Hub
iSerial 1 6400
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x40
Self Powered
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type none
wMaxPacketSize 8
bInterval 255
Language IDs: (length=4)
0000 (null)((null))
========== STEP 2: Results of executing "modprobe usb-storage"
----- dmesg output
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
----- syslog output
Mar 11 20:10:24 mycroft kernel: Initializing USB Mass Storage driver...
Mar 11 20:10:24 mycroft kernel: usb.c: registered new driver usb-storage
Mar 11 20:10:24 mycroft kernel: USB Mass Storage support registered.
----- lsmod output
Module Size Used by
usb-storage 43696 0 (unused)
es1370 24944 0 (autoclean)
parport_pc 21696 1 (autoclean)
lp 6624 0 (autoclean)
parport 25120 1 (autoclean) [parport_pc lp]
ide-scsi 7776 0
scsi_mod 85152 1 [usb-storage ide-scsi]
usb-uhci 21616 0 (unused)
usbcore 63488 1 [usb-storage usb-uhci]
========== STEP 3: Results of turning on camera
----- dmesg output
hub.c: port 1, portstatus 100, change 0, 12 Mb/s
hub.c: port 2, portstatus 101, change 1, 12 Mb/s
hub.c: port 2 connection change
hub.c: port 2, portstatus 101, change 1, 12 Mb/s
hub.c: port 2, portstatus 101, change 0, 12 Mb/s
hub.c: port 2, portstatus 101, change 0, 12 Mb/s
hub.c: port 2, portstatus 101, change 0, 12 Mb/s
hub.c: port 2, portstatus 101, change 0, 12 Mb/s
hub.c: port 2, portstatus 103, change 0, 12 Mb/s
hub.c: new USB device 00:07.2-2, assigned address 2
usb.c: kmalloc IF c9923740, numif 1
usb.c: new device strings: Mfr=1, Product=2, SerialNumber=0
usb.c: USB device number 2 default language ID 0x409
Manufacturer: Sony
Product: Sony DSC
usb-storage: act_altsettting is 0
usb-storage: id_index calculated to be: 21
usb-storage: Array length appears to be: 68
usb-storage: Vendor: Sony
usb-storage: Product: DSC-S30/S70/S75/505V/F505/F707
usb-storage: USB Mass Storage device detected
usb-storage: Endpoints: In: 0xcb698fb4 Out: 0xcb698fa0 Int: 0xcb698fc8
(Period 255)
usb-storage: New GUID 054c00100000000000000000
usb-storage: Transport: Control/Bulk
usb-storage: Protocol: Transparent SCSI
usb-storage: *** thread sleeping.
scsi1 : SCSI emulation for USB Mass Storage devices
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command INQUIRY (6 bytes)
usb-storage: 12 00 00 00 ff 00 00 00 00 00 00 00
usb-storage: Invoking Mode Translation
usb-storage: Call to usb_stor_control_msg() returned 6
usb-storage: usb_stor_transfer_partial(): xfer 255 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 72/255
usb-storage: CB data stage result is 0x1
usb-storage: -- CB transport device requiring auto-sense
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Call to usb_stor_control_msg() returned 6
usb-storage: usb_stor_transfer_partial(): xfer 18 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
usb-storage: No Sense: no additional sense information
usb-storage: Fixing INQUIRY data to show SCSI rev 2
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
Vendor: Sony Model: Sony DSC Rev: 3.28
Type: Direct-Access ANSI SCSI revision: 02
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Bad LUN (0/1)
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Bad target number (1/0)
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Bad target number (2/0)
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Bad target number (3/0)
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Bad target number (4/0)
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Bad target number (5/0)
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Bad target number (6/0)
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Bad target number (7/0)
usb-storage: *** thread sleeping.
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 2
usb.c: usb-storage driver claimed interface c9923740
usb.c: kusbd: /sbin/hotplug add 2
hub.c: port 1, portstatus 100, change 0, 12 Mb/s
hub.c: port 2, portstatus 103, change 0, 12 Mb/s
----- syslog output
Mar 11 20:13:00 mycroft kernel: hub.c: new USB device 00:07.2-2, assigned
address 2
Mar 11 20:13:00 mycroft kernel: Manufacturer: Sony
Mar 11 20:13:00 mycroft kernel: Product: Sony DSC
Mar 11 20:13:00 mycroft kernel: scsi1 : SCSI emulation for USB Mass Storage
devices
Mar 11 20:13:00 mycroft kernel: Vendor: Sony Model: Sony DSC
Rev: 3.28
Mar 11 20:13:00 mycroft kernel: Type: Direct-Access
ANSI SCSI revision: 02
Mar 11 20:13:00 mycroft /sbin/hotplug: arguments (usb) env (PWD=/etc/hotplug
HOSTNAME=mycroft DEVICE=/proc/bus/usb/001/002 INTERFACE=8/255/1 ACTION=add
DEBUG=kernel MACHTYPE=i386-redhat-linux-gnu OLDPWD=/ DEVFS=/proc/bus/usb
TYPE=0/0/0 SHLVL=1 SHELL=/bin/bash HOSTTYPE=i386 OSTYPE=linux-gnu HOME=/
TERM=dumb PATH=/bin:/sbin:/usr/sbin:/usr/bin PRODUCT=54c/10/328
_=/usr/bin/env)
Mar 11 20:13:01 mycroft /sbin/hotplug: invoke /etc/hotplug/usb.agent ()
Mar 11 20:13:01 mycroft /etc/hotplug/usb.agent: Modprobe and setup
usb-storage for USB product 54c/10/328
----- /proc/bus/usb/devices
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.00 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 0.00
S: Product=USB UHCI Root Hub
S: SerialNumber=6400
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=255ms
T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 1.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=054c ProdID=0010 Rev= 3.28
S: Manufacturer=Sony
S: Product=Sony DSC
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 2mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=08(stor.) Sub=ff Prot=01 Driver=usb-storage
E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 8 Ivl=255ms
----- lsusb -v output
Unknown line at line 1809
Duplicate HUT Usage Spec at line 2650
Bus 001 Device 001: ID 0000:0000 Virtual Hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.00
bDeviceClass 9 Hub
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x0000 Virtual
idProduct 0x0000 Hub
bcdDevice 0.00
iManufacturer 0
iProduct 2 USB UHCI Root Hub
iSerial 1 6400
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x40
Self Powered
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type none
wMaxPacketSize 8
bInterval 255
Language IDs: (length=4)
0000 (null)((null))
Bus 001 Device 002: ID 054c:0010 Sony Corp. DSC-S30/S70/S75/F505V/F505/FD92
Cybershot/Mavica Digital Camera
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.00
bDeviceClass 0 Interface
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x054c Sony Corp.
idProduct 0x0010 DSC-S30/S70/S75/F505V/F505/FD92 Cybershot/Mavica
Digital Camera
bcdDevice 3.28
iManufacturer 1 Sony
iProduct 2 Sony DSC
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 39
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x40
Self Powered
MaxPower 2mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 255
bInterfaceProtocol 1
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type none
wMaxPacketSize 64
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type none
wMaxPacketSize 64
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type none
wMaxPacketSize 8
bInterval 255
Language IDs: (length=4)
0409 English(US)
========== STEP 4: Results of "mount /mnt/camera"
----- dmesg output
rol_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 18 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
usb-storage: No Sense: no additional sense information
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 32 00 00 01 00 00 00
usb-storage: Invoking Mode Translation
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 512 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 512/512
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- CB transport device requiring auto-sense
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 18 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
usb-storage: No Sense: no additional sense information
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 33 00 00 01 00 00 00
usb-storage: Invoking Mode Translation
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 512 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 512/512
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- CB transport device requiring auto-sense
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 18 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
usb-storage: No Sense: no additional sense information
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 34 00 00 01 00 00 00
usb-storage: Invoking Mode Translation
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 512 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 512/512
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- CB transport device requiring auto-sense
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 18 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
usb-storage: No Sense: no additional sense information
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 35 00 00 01 00 00 00
usb-storage: Invoking Mode Translation
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 512 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 512/512
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- CB transport device requiring auto-sense
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 18 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
usb-storage: No Sense: no additional sense information
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 36 00 00 01 00 00 00
usb-storage: Invoking Mode Translation
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 512 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 512/512
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- CB transport device requiring auto-sense
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 18 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
usb-storage: No Sense: no additional sense information
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 37 00 00 01 00 00 00
usb-storage: Invoking Mode Translation
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 512 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 512/512
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- CB transport device requiring auto-sense
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 18 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
usb-storage: No Sense: no additional sense information
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 38 00 00 01 00 00 00
usb-storage: Invoking Mode Translation
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 512 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 512/512
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- CB transport device requiring auto-sense
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 18 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
usb-storage: No Sense: no additional sense information
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 39 00 00 01 00 00 00
usb-storage: Invoking Mode Translation
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 512 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 512/512
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- CB transport device requiring auto-sense
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 18 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
usb-storage: No Sense: no additional sense information
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 3a 00 00 01 00 00 00
usb-storage: Invoking Mode Translation
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 512 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 512/512
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- CB transport device requiring auto-sense
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 18 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
usb-storage: No Sense: no additional sense information
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 3b 00 00 01 00 00 00
usb-storage: Invoking Mode Translation
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 512 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 512/512
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- CB transport device requiring auto-sense
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 18 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
usb-storage: No Sense: no additional sense information
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 3c 00 00 01 00 00 00
usb-storage: Invoking Mode Translation
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 512 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 512/512
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- CB transport device requiring auto-sense
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 18 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
usb-storage: No Sense: no additional sense information
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 3d 00 00 01 00 00 00
usb-storage: Invoking Mode Translation
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 512 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 512/512
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- CB transport device requiring auto-sense
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 18 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
usb-storage: No Sense: no additional sense information
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 3e 00 00 01 00 00 00
usb-storage: Invoking Mode Translation
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 512 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 512/512
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- CB transport device requiring auto-sense
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 18 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
usb-storage: No Sense: no additional sense information
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 3f 00 00 01 00 00 00
usb-storage: Invoking Mode Translation
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 512 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 512/512
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- CB transport device requiring auto-sense
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 18 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
usb-storage: No Sense: no additional sense information
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
----- syslog output
Mar 11 20:21:46 mycroft kernel: Attached scsi removable disk sda at scsi1,
channel 0, id 0, lun 0
Mar 11 20:21:46 mycroft kernel: SCSI device sda: 15840 512-byte hdwr sectors
(8
MB)
Mar 11 20:21:46 mycroft kernel: sda: Write Protect is off
Mar 11 20:21:46 mycroft kernel: sda:<7>usb-storage: queuecommand() called
Mar 11 20:21:46 mycroft kernel: sda1
Mar 11 20:21:46 mycroft kernel: usb-uhci.c: interrupt, status 3, frame# 1424
Mar 11 20:21:46 mycroft modprobe: modprobe: Can't locate module nls_iso8859-1
========== STEP 5: Results of "umount /mnt/camera"
----- dmesg output
----- syslog output
----- lsmod output
----- /proc/bus/usb/devices
----- lspci output
----- lspci -v -s 7.2 output
----- lsusb -v output
========== STEP 6: Results of removing chip 1 and insert chip 2
----- dmesg output
hub.c: port 1, portstatus 100, change 0, 12 Mb/s
hub.c: port 2, portstatus 100, change 3, 12 Mb/s
hub.c: port 2 connection change
hub.c: port 2, portstatus 100, change 3, 12 Mb/s
usb.c: USB disconnect on device 00:07.2-2 address 2
usb-storage: storage_disconnect() called
usb-storage: -- releasing main URB
usb-storage: -- usb_unlink_urb() returned -19
usb.c: kusbd: /sbin/hotplug remove 2
hub.c: port 1, portstatus 100, change 0, 12 Mb/s
hub.c: port 2, portstatus 100, change 2, 12 Mb/s
hub.c: port 2 enable change, status 100
----- syslog
Mar 11 20:25:03 mycroft kernel: usb.c: USB disconnect on device 00:07.2-2
address 2
Mar 11 20:25:03 mycroft /sbin/hotplug: arguments (usb) env (PWD=/etc/hotplug
HOSTNAME=mycroft DEVICE=/proc/bus/usb/001/002 INTERFACE=8/255/1 ACTION=remove
DEBUG=kernel MACHTYPE=i386-redhat-linux-gnu OLDPWD=/ DEVFS=/proc/bus/usb
TYPE=0/0/0 SHLVL=1 SHELL=/bin/bash HOSTTYPE=i386 OSTYPE=linux-gnu HOME=/
TERM=dumb PATH=/bin:/sbin:/usr/sbin:/usr/bin PRODUCT=54c/10/328
_=/usr/bin/env)
Mar 11 20:25:03 mycroft /sbin/hotplug: invoke /etc/hotplug/usb.agent () output
----- /proc/bus/usb/devices
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.00 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 0.00
S: Product=USB UHCI Root Hub
S: SerialNumber=6400
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=255ms
----- lsusb -v output
Unknown line at line 1809
Duplicate HUT Usage Spec at line 2650
Bus 001 Device 001: ID 0000:0000 Virtual Hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.00
bDeviceClass 9 Hub
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x0000 Virtual
idProduct 0x0000 Hub
bcdDevice 0.00
iManufacturer 0
iProduct 2 USB UHCI Root Hub
iSerial 1 6400
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x40
Self Powered
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type none
wMaxPacketSize 8
bInterval 255
Language IDs: (length=4)
0000 (null)((null))
========== STEP 7: Results of inserting different chip
----- dmesg output
hub.c: port 1, portstatus 100, change 0, 12 Mb/s
hub.c: port 2, portstatus 101, change 1, 12 Mb/s
hub.c: port 2 connection change
hub.c: port 2, portstatus 101, change 1, 12 Mb/s
hub.c: port 2, portstatus 101, change 0, 12 Mb/s
hub.c: port 2, portstatus 101, change 0, 12 Mb/s
hub.c: port 2, portstatus 101, change 0, 12 Mb/s
hub.c: port 2, portstatus 101, change 0, 12 Mb/s
hub.c: port 2, portstatus 103, change 0, 12 Mb/s
hub.c: new USB device 00:07.2-2, assigned address 3
usb.c: kmalloc IF c99239a0, numif 1
usb.c: new device strings: Mfr=1, Product=2, SerialNumber=0
usb.c: USB device number 3 default language ID 0x409
Manufacturer: Sony
Product: Sony DSC
usb-storage: act_altsettting is 0
usb-storage: id_index calculated to be: 21
usb-storage: Array length appears to be: 68
usb-storage: Vendor: Sony
usb-storage: Product: DSC-S30/S70/S75/505V/F505/F707
usb-storage: USB Mass Storage device detected
usb-storage: Endpoints: In: 0xc1325e74 Out: 0xc1325e60 Int: 0xc1325e88
(Period 255)
usb-storage: Found existing GUID 054c00100000000000000000
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 3
usb.c: usb-storage driver claimed interface c99239a0
usb.c: kusbd: /sbin/hotplug add 3
hub.c: port 1, portstatus 100, change 0, 12 Mb/s
hub.c: port 2, portstatus 103, change 0, 12 Mb/s
----- syslog output
Mar 11 20:30:48 mycroft kernel: hub.c: new USB device 00:07.2-2, assigned
address 3
Mar 11 20:30:48 mycroft kernel: Manufacturer: Sony
Mar 11 20:30:48 mycroft kernel: Product: Sony DSC
Mar 11 20:30:48 mycroft /sbin/hotplug: arguments (usb) env (PWD=/etc/hotplug
HOSTNAME=mycroft DEVICE=/proc/bus/usb/001/003 INTERFACE=8/255/1 ACTION=add
DEBUG=kernel MACHTYPE=i386-redhat-linux-gnu OLDPWD=/ DEVFS=/proc/bus/usb
TYPE=0/0/0 SHLVL=1 SHELL=/bin/bash HOSTTYPE=i386 OSTYPE=linux-gnu HOME=/
TERM=dumb PATH=/bin:/sbin:/usr/sbin:/usr/bin PRODUCT=54c/10/328
_=/usr/bin/env)
Mar 11 20:30:48 mycroft /sbin/hotplug: invoke /etc/hotplug/usb.agent ()
Mar 11 20:30:48 mycroft /etc/hotplug/usb.agent: Modprobe and setup
usb-storage for USB product 54c/10/328
----- /proc/bus/usb/devices
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.00 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 0.00
S: Product=USB UHCI Root Hub
S: SerialNumber=6400
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=255ms
T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=054c ProdID=0010 Rev= 3.28
S: Manufacturer=Sony
S: Product=Sony DSC
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 2mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=08(stor.) Sub=ff Prot=01 Driver=usb-storage
E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 8 Ivl=255ms
----- lsusb -v output
Unknown line at line 1809
Duplicate HUT Usage Spec at line 2650
Bus 001 Device 001: ID 0000:0000 Virtual Hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.00
bDeviceClass 9 Hub
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x0000 Virtual
idProduct 0x0000 Hub
bcdDevice 0.00
iManufacturer 0
iProduct 2 USB UHCI Root Hub
iSerial 1 6400
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x40
Self Powered
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type none
wMaxPacketSize 8
bInterval 255
Language IDs: (length=4)
0000 (null)((null))
Bus 001 Device 003: ID 054c:0010 Sony Corp. DSC-S30/S70/S75/F505V/F505/FD92
Cybershot/Mavica Digital Camera
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.00
bDeviceClass 0 Interface
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x054c Sony Corp.
idProduct 0x0010 DSC-S30/S70/S75/F505V/F505/FD92 Cybershot/Mavica
Digital Camera
bcdDevice 3.28
iManufacturer 1 Sony
iProduct 2 Sony DSC
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 39
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x40
Self Powered
MaxPower 2mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 255
bInterfaceProtocol 1
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type none
wMaxPacketSize 64
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type none
wMaxPacketSize 64
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type none
wMaxPacketSize 8
bInterval 255
Language IDs: (length=4)
0409 English(US)
========== STEP 8: Results of "mount /mnt/camera"
----- dmesg output
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Skipping START_STOP command
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Skipping START_STOP command
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 19 00 00 01 00 00 00
usb-storage: Invoking Mode Translation
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 512 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 512/512
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- CB transport device requiring auto-sense
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 18 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
usb-storage: No Sense: no additional sense information
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
FAT: bogus logical sector size 65535
VFS: Can't find a valid FAT filesystem on dev 08:01.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Skipping START_STOP command
usb-storage: *** thread sleeping.
----- syslog output
Mar 11 20:36:05 mycroft kernel: FAT: bogus logical sector size 65535
Mar 11 20:36:05 mycroft kernel: VFS: Can't find a valid FAT filesystem on dev
08:01.
========== STEP 9: Results of "rmmod usb-storage"
----- dmesg output
usb-storage: usb_stor_exit() called
usb-storage: -- calling usb_deregister()
usb.c: deregistering driver usb-storage
usb-storage: storage_disconnect() called
usb-storage: -- releasing main URB
usb-storage: -- usb_unlink_urb() returned -19
usb-storage: -- calling scsi_unregister_module()
usb-storage: release() called for host usb-storage
usb-storage: -- sending US_ACT_EXIT command to thread
usb-storage: *** thread awakened.
usb-storage: -- US_ACT_EXIT command received
scsi : 1 host left.
----- syslog output
Mar 11 20:40:32 mycroft kernel: usb.c: deregistering driver usb-storage
Mar 11 20:40:32 mycroft kernel: scsi : 1 host left.
----- lsmod output
Module Size Used by
nls_cp437 4368 0 (autoclean)
sd_mod 10272 0 (autoclean)
es1370 24944 0 (autoclean)
parport_pc 21696 1 (autoclean)
lp 6624 0 (autoclean)
parport 25120 1 (autoclean) [parport_pc lp]
ide-scsi 7776 0
scsi_mod 85152 2 [sd_mod ide-scsi]
usb-uhci 21616 0 (unused)
usbcore 63488 1 [usb-uhci]
----- /proc/bus/usb/devices
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.00 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 0.00
S: Product=USB UHCI Root Hub
S: SerialNumber=6400
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=255ms
T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=054c ProdID=0010 Rev= 3.28
S: Manufacturer=Sony
S: Product=Sony DSC
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 2mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=08(stor.) Sub=ff Prot=01 Driver=(none)
E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 8 Ivl=255ms
========== STEP 10: Results of "insmod usb-storage"
----- dmesg output
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
usb-storage: act_altsettting is 0
usb-storage: id_index calculated to be: 21
usb-storage: Array length appears to be: 68
usb-storage: Vendor: Sony
usb-storage: Product: DSC-S30/S70/S75/505V/F505/F707
usb-storage: USB Mass Storage device detected
usb-storage: Endpoints: In: 0xc1325e74 Out: 0xc1325e60 Int: 0xc1325e88
(Period 255)
usb-storage: New GUID 054c00100000000000000000
usb-storage: Transport: Control/Bulk
usb-storage: Protocol: Transparent SCSI
usb-storage: *** thread sleeping.
scsi1 : SCSI emulation for USB Mass Storage devices
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command INQUIRY (6 bytes)
usb-storage: 12 00 00 00 ff 00 00 00 00 00 00 00
usb-storage: Invoking Mode Translation
usb-storage: Call to usb_stor_control_msg() returned 6
usb-storage: usb_stor_transfer_partial(): xfer 255 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 72/255
usb-storage: CB data stage result is 0x1
usb-storage: -- CB transport device requiring auto-sense
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Call to usb_stor_control_msg() returned 6
usb-storage: usb_stor_transfer_partial(): xfer 18 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
usb-storage: No Sense: no additional sense information
usb-storage: Fixing INQUIRY data to show SCSI rev 2
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
Vendor: Sony Model: Sony DSC Rev: 3.28
Type: Direct-Access ANSI SCSI revision: 02
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Bad LUN (0/1)
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Bad target number (1/0)
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Bad target number (2/0)
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Bad target number (3/0)
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Bad target number (4/0)
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Bad target number (5/0)
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Bad target number (6/0)
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Bad target number (7/0)
usb-storage: *** thread sleeping.
Attached scsi removable disk sda at scsi1, channel 0, id 0, lun 0
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00 00 00 00 00 00 cf
usb-storage: Invoking Mode Translation
usb-storage: Call to usb_stor_control_msg() returned 6
usb-storage: -- CB transport device requiring auto-sense
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Call to usb_stor_control_msg() returned 6
usb-storage: usb_stor_transfer_partial(): xfer 18 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
usb-storage: No Sense: no additional sense information
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command READ_CAPACITY (10 bytes)
usb-storage: 25 00 00 00 00 00 00 00 00 00 00 cf
usb-storage: Invoking Mode Translation
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 8 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 8/8
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- CB transport device requiring auto-sense
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 18 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
usb-storage: No Sense: no additional sense information
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
SCSI device sda: 253696 512-byte hdwr sectors (130 MB)
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command MODE_SENSE (6 bytes)
usb-storage: 1a 00 3f 00 ff 00 00 00 00 00 00 cf
usb-storage: Invoking Mode Translation
usb-storage: Call to usb_stor_control_msg() returned 12
usb-storage: usb_stor_transfer_partial(): xfer 255 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 52/255
usb-storage: CB data stage result is 0x1
usb-storage: -- CB transport device requiring auto-sense
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Call to usb_stor_control_msg() returned 12
usb-storage: usb_stor_transfer_partial(): xfer 18 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
usb-storage: No Sense: no additional sense information
usb-storage: -- converting 10 byte sense data to 6 byte
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
sda: Write Protect is off
sda:<7>usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 00 00 00 08 00 00 00
usb-storage: Invoking Mode Translation
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 4096 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 4096/4096
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- CB transport device requiring auto-sense
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 18 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
usb-storage: No Sense: no additional sense information
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
sda1
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 3
usb.c: usb-storage driver claimed interface c99239a0
USB Mass Storage support registered.
----- syslog output
Mar 11 20:43:09 mycroft kernel: Initializing USB Mass Storage driver...
Mar 11 20:43:09 mycroft kernel: usb.c: registered new driver usb-storage
Mar 11 20:43:09 mycroft kernel: scsi1 : SCSI emulation for USB Mass Storage
devices
Mar 11 20:43:09 mycroft kernel: Vendor: Sony Model: Sony DSC
Rev: 3.28
Mar 11 20:43:09 mycroft kernel: Type: Direct-Access
ANSI SCSI revision: 02
Mar 11 20:43:09 mycroft kernel: Attached scsi removable disk sda at scsi1,
channel 0, id 0, lun 0
Mar 11 20:43:09 mycroft kernel: SCSI device sda: 253696 512-byte hdwr sectors
(130 MB)
Mar 11 20:43:09 mycroft kernel: sda: Write Protect is off
Mar 11 20:43:09 mycroft kernel: sda:<7>usb-storage: queuecommand() called
Mar 11 20:43:09 mycroft kernel: sda1
Mar 11 20:43:09 mycroft kernel: USB Mass Storage support registered.
----- lsusb -v output
Unknown line at line 1809
Duplicate HUT Usage Spec at line 2650
Bus 001 Device 001: ID 0000:0000 Virtual Hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.00
bDeviceClass 9 Hub
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x0000 Virtual
idProduct 0x0000 Hub
bcdDevice 0.00
iManufacturer 0
iProduct 2 USB UHCI Root Hub
iSerial 1 6400
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x40
Self Powered
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type none
wMaxPacketSize 8
bInterval 255
Language IDs: (length=4)
0000 (null)((null))
Bus 001 Device 003: ID 054c:0010 Sony Corp. DSC-S30/S70/S75/F505V/F505/FD92
Cybershot/Mavica Digital Camera
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.00
bDeviceClass 0 Interface
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x054c Sony Corp.
idProduct 0x0010 DSC-S30/S70/S75/F505V/F505/FD92 Cybershot/Mavica
Digital Camera
bcdDevice 3.28
iManufacturer 1 Sony
iProduct 2 Sony DSC
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 39
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x40
Self Powered
MaxPower 2mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 255
bInterfaceProtocol 1
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type none
wMaxPacketSize 64
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type none
wMaxPacketSize 64
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type none
wMaxPacketSize 8
bInterval 255
Language IDs: (length=4)
0409 English(US)
========== STEP 11: Results of "mount /mnt/camera"
----- dmesg output
rol_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 18 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
usb-storage: No Sense: no additional sense information
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 72 00 00 01 00 00 00
usb-storage: Invoking Mode Translation
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 512 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 512/512
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- CB transport device requiring auto-sense
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 18 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
usb-storage: No Sense: no additional sense information
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 73 00 00 01 00 00 00
usb-storage: Invoking Mode Translation
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 512 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 512/512
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- CB transport device requiring auto-sense
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 18 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
usb-storage: No Sense: no additional sense information
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 74 00 00 01 00 00 00
usb-storage: Invoking Mode Translation
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 512 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 512/512
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- CB transport device requiring auto-sense
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 18 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
usb-storage: No Sense: no additional sense information
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 75 00 00 01 00 00 00
usb-storage: Invoking Mode Translation
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 512 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 512/512
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- CB transport device requiring auto-sense
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 18 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
usb-storage: No Sense: no additional sense information
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 76 00 00 01 00 00 00
usb-storage: Invoking Mode Translation
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 512 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 512/512
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- CB transport device requiring auto-sense
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 18 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
usb-storage: No Sense: no additional sense information
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 77 00 00 01 00 00 00
usb-storage: Invoking Mode Translation
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 512 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 512/512
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- CB transport device requiring auto-sense
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 18 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
usb-storage: No Sense: no additional sense information
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 78 00 00 01 00 00 00
usb-storage: Invoking Mode Translation
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 512 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 512/512
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- CB transport device requiring auto-sense
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 18 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
usb-storage: No Sense: no additional sense information
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 79 00 00 01 00 00 00
usb-storage: Invoking Mode Translation
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 512 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 512/512
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- CB transport device requiring auto-sense
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 18 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
usb-storage: No Sense: no additional sense information
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 7a 00 00 01 00 00 00
usb-storage: Invoking Mode Translation
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 512 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 512/512
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- CB transport device requiring auto-sense
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 18 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
usb-storage: No Sense: no additional sense information
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 7b 00 00 01 00 00 00
usb-storage: Invoking Mode Translation
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 512 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 512/512
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- CB transport device requiring auto-sense
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 18 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
usb-storage: No Sense: no additional sense information
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 7c 00 00 01 00 00 00
usb-storage: Invoking Mode Translation
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 512 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 512/512
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- CB transport device requiring auto-sense
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 18 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
usb-storage: No Sense: no additional sense information
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 7d 00 00 01 00 00 00
usb-storage: Invoking Mode Translation
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 512 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 512/512
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- CB transport device requiring auto-sense
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 18 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
usb-storage: No Sense: no additional sense information
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 7e 00 00 01 00 00 00
usb-storage: Invoking Mode Translation
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 512 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 512/512
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- CB transport device requiring auto-sense
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 18 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
usb-storage: No Sense: no additional sense information
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 7f 00 00 01 00 00 00
usb-storage: Invoking Mode Translation
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 512 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 512/512
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- CB transport device requiring auto-sense
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Call to usb_stor_control_msg() returned 10
usb-storage: usb_stor_transfer_partial(): xfer 18 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: CB data stage result is 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
usb-storage: No Sense: no additional sense information
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
----- syslog output
Mar 11 20:48:23 mycroft kernel: usb-uhci.c: interrupt, status 3, frame# 1811
Mar 11 20:48:23 mycroft modprobe: modprobe: Can't locate module nls_iso8859-1
-------------------------------------------------------
This SF.net email is sponsored by:Crypto Challenge is now open!
Get cracking and register here for some mind boggling fun and
the chance of winning an Apple iPod:
http://ads.sourceforge.net/cgi-bin/redirect.pl?thaw0031en
_______________________________________________
[EMAIL PROTECTED]
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-users
