LS / Dears Friends, For some time now i'm trying to run minolta Dual Scan III with Vuescan 7.6.48 on my Linux Red Hat 2.4.20-19-9. I read a lot of worrying messages that it doesn't work read the Hamrick instructions; trying to emulate them, but still after a few slides it hangs; vuescan also calls a lot of time for (re-) calibration.
This is the way i run the program: "[EMAIL PROTECTED] marcel]$ cd /usr/local/vuescan" "[EMAIL PROTECTED] vuescan]$ env lang=c ./vuescan" then after a few runs it tells: sh: line 1: xv: command not found the log tells ["/var/log/messages:"] Jul 26 11:02:59 kf-pij-tg01-0437 kernel: hub.c: new USB device 00:0b.0-1, assigned address 3 Jul 26 11:02:59 kf-pij-tg01-0437 kernel: scanner.c: USB scanner device (0x0686/0x400d) now attached to scanner1 Jul 26 11:03:03 kf-pij-tg01-0437 /etc/hotplug/usb.agent: Setup scanner for USB product 686/400d/1 Jul 26 11:03:03 kf-pij-tg01-0437 /etc/hotplug/usb.agent: Setup usbcam for USB product 686/400d/1 Jul 26 11:03:03 kf-pij-tg01-0437 /etc/hotplug/usb.agent: Module setup usbcam for USB product 686/400d/1 jul 26 11:03:03 kf-pij-tg01-0437 devlabel: devlabel service started/restarted Jul 26 11:09:56 kf-pij-tg01-0437 kernel: scanner.c: read_scanner(1): funky result:-75. Consult Documentation/usb/scanner.txt.Jul 26 11:10:06 kf-pij-tg01-0437 kernel: usb_control/bulk_msg: timeout Jul 26 11:10:25 kf-pij-tg01-0437 kernel: scanner.c: read_scanner(1): funky result:-71. Consult Documentation/usb/scanner.txt.Jul 26 11:10:26 kf-pij-tg01-0437 kernel: usb.c: USB disconnect on device 00:0b.0-1 address 3 Jul 26 11:12:15 kf-pij-tg01-0437 kernel: scanner.c: read_scanner(1): excessive NAK's received Jul 26 11:12:15 kf-pij-tg01-0437 kernel: scanner.c: write_scanner(1): funky result: -19. Consult Documentataion/usb/scanner.txt. Jul 26 11:12:15 kf-pij-tg01-0437 kernel: scanner.c: read_scanner(1): funky result:-19. Consult Documentation/usb/scanner.txt.Jul 26 11:12:16 kf-pij-tg01-0437 kernel: Unable to handle kernel paging request at virtual address 00050046 Jul 26 11:12:16 kf-pij-tg01-0437 kernel: printing eip: Jul 26 11:12:16 kf-pij-tg01-0437 kernel: e08e4488 Jul 26 11:12:16 kf-pij-tg01-0437 kernel: *pde = 00000000 Jul 26 11:12:16 kf-pij-tg01-0437 kernel: Oops: 0000 Jul 26 11:12:16 kf-pij-tg01-0437 kernel: parport_pc lp parport autofs ipt_REJECT iptable_filter ip_tables sg sr_mod ide-scsi scsi_mod ide-cd cdrom pegasus scanner keybdev mousedev hid input usb-uhci also from log: /var/log/messages: "Jul 26 12:24:11 kf-pij-tg01-0437 kernel: usb_control/bulk_msg: timeout" "cat /proc/bus/usb/devices" I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=ff Prot=ff MxPS=64 #Cfgs= 1 P: Vendor=0686 ProdID=400d Rev= 0.01 S: Manufacturer=MINOLTA S: Product=DiMAGE Scan Dual3 S: SerialNumber=0000000000000000 Now i'm at a lose. Do you know were to start and/or what to change. Many thanks Marcel ------------------------------------------------------- This SF.Net email sponsored by: Free pre-built ASP.NET sites including Data Reports, E-commerce, Portals, and Forums are available now. Download today and enter to win an XBOX or Visual Studio .NET. http://aspnet.click-url.com/go/psa00100003ave/direct;at.aspnet_072303_01/01 _______________________________________________ [EMAIL PROTECTED] To unsubscribe, use the last form field at: https://lists.sourceforge.net/lists/listinfo/linux-usb-users
