Ignore them (or put cards in all the drives). On Fri, 27 Feb 2004, Optimized wrote:
> I'm now able to mount it, I had to use /dev/sdd1. > > But I still get these messages on system startup, what can I do? > > Thanks again > > On Fri, 2004-02-27 at 02:13, Stephen J. Gowdy wrote: > > Are you sure you are trying to mount the correct device? > > > > On Thu, 26 Feb 2004, Optimized wrote: > > > > > Hello, > > > > > > I just bought a noname USB internal multi-card reader and plugged it > > > into my Asus P4C800-E board. > > > > > > I use Fedora Core 1 (2.4.22-1.2174.nptl) and CONFIG_SCSI_MULTI_LUN=y in > > > my custom kernel config. > > > > > > If I enable BIOS Legacy USB, linux doesn't boot (it hangs on kernel > > > startup.) > > > > > > If I disable BIOS Legacy USB, linux does boot but when it gets to kudzu > > > (hardware detection) it says "missing char major ..." on a few dozens of > > > line > > > > > > I'm unable to mount my SD card and if I dmesg : > > > > > > ansfer_partial(): transfer complete > > > usb-storage: Bulk data transfer result 0x0 > > > usb-storage: Attempting to get CSW... > > > usb-storage: Bulk status result = 0 > > > usb-storage: Bulk status Sig 0x53425355 T 0x242 R 0 Stat 0x0 > > > usb-storage: -- Result from auto-sense is 0 > > > usb-storage: -- code: 0x70, key: 0x2, ASC: 0x3a, ASCQ: 0x0 > > > usb-storage: Not Ready: media not present > > > usb-storage: scsi cmd done, result=0x2 > > > usb-storage: *** thread sleeping. > > > usb-storage: queuecommand() called > > > usb-storage: *** thread awakened. > > > usb-storage: Command TEST_UNIT_READY (6 bytes) > > > usb-storage: 00 60 00 00 00 00 00 00 00 00 16 c0 > > > usb-storage: Bulk command S 0x43425355 T 0x243 Trg 0 LUN 3 L 0 F 0 CL 6 > > > usb-storage: Bulk command transfer result=0 > > > usb-storage: Attempting to get CSW... > > > usb-storage: Bulk status result = 0 > > > usb-storage: Bulk status Sig 0x53425355 T 0x243 R 0 Stat 0x1 > > > usb-storage: -- transport indicates command failure > > > usb-storage: Issuing auto-REQUEST_SENSE > > > usb-storage: Bulk command S 0x43425355 T 0x244 Trg 0 LUN 3 L 18 F 128 CL > > > 6 > > > usb-storage: Bulk command transfer result=0 > > > usb-storage: usb_stor_transfer_partial(): xfer 18 bytes > > > usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18 > > > usb-storage: usb_stor_transfer_partial(): transfer complete > > > usb-storage: Bulk data transfer result 0x0 > > > usb-storage: Attempting to get CSW... > > > usb-storage: Bulk status result = 0 > > > usb-storage: Bulk status Sig 0x53425355 T 0x244 R 0 Stat 0x0 > > > usb-storage: -- Result from auto-sense is 0 > > > usb-storage: -- code: 0x70, key: 0x2, ASC: 0x3a, ASCQ: 0x0 > > > usb-storage: Not Ready: media not present > > > usb-storage: scsi cmd done, result=0x2 > > > usb-storage: *** thread sleeping. > > > usb-storage: queuecommand() called > > > usb-storage: *** thread awakened. > > > usb-storage: Command TEST_UNIT_READY (6 bytes) > > > usb-storage: 00 60 00 00 00 00 00 00 00 00 16 c0 > > > usb-storage: Bulk command S 0x43425355 T 0x245 Trg 0 LUN 3 L 0 F 0 CL 6 > > > usb-storage: Bulk command transfer result=0 > > > usb-storage: Attempting to get CSW... > > > usb-storage: Bulk status result = 0 > > > usb-storage: Bulk status Sig 0x53425355 T 0x245 R 0 Stat 0x1 > > > usb-storage: -- transport indicates command failure > > > usb-storage: Issuing auto-REQUEST_SENSE > > > usb-storage: Bulk command S 0x43425355 T 0x246 Trg 0 LUN 3 L 18 F 128 CL > > > 6 > > > usb-storage: Bulk command transfer result=0 > > > usb-storage: usb_stor_transfer_partial(): xfer 18 bytes > > > usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18 > > > usb-storage: usb_stor_transfer_partial(): transfer complete > > > usb-storage: Bulk data transfer result 0x0 > > > usb-storage: Attempting to get CSW... > > > usb-storage: Bulk status result = 0 > > > usb-storage: Bulk status Sig 0x53425355 T 0x246 R 0 Stat 0x0 > > > usb-storage: -- Result from auto-sense is 0 > > > usb-storage: -- code: 0x70, key: 0x2, ASC: 0x3a, ASCQ: 0x0 > > > usb-storage: Not Ready: media not present > > > usb-storage: scsi cmd done, result=0x2 > > > usb-storage: *** thread sleeping. > > > usb-storage: queuecommand() called > > > usb-storage: *** thread awakened. > > > usb-storage: Command TEST_UNIT_READY (6 bytes) > > > usb-storage: 00 60 00 00 00 00 00 00 00 00 16 c0 > > > usb-storage: Bulk command S 0x43425355 T 0x247 Trg 0 LUN 3 L 0 F 0 CL 6 > > > usb-storage: Bulk command transfer result=0 > > > usb-storage: Attempting to get CSW... > > > usb-storage: Bulk status result = 0 > > > usb-storage: Bulk status Sig 0x53425355 T 0x247 R 0 Stat 0x1 > > > usb-storage: -- transport indicates command failure > > > usb-storage: Issuing auto-REQUEST_SENSE > > > usb-storage: Bulk command S 0x43425355 T 0x248 Trg 0 LUN 3 L 18 F 128 CL > > > 6 > > > usb-storage: Bulk command transfer result=0 > > > usb-storage: usb_stor_transfer_partial(): xfer 18 bytes > > > usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18 > > > usb-storage: usb_stor_transfer_partial(): transfer complete > > > usb-storage: Bulk data transfer result 0x0 > > > usb-storage: Attempting to get CSW... > > > usb-storage: Bulk status result = 0 > > > usb-storage: Bulk status Sig 0x53425355 T 0x248 R 0 Stat 0x0 > > > usb-storage: -- Result from auto-sense is 0 > > > usb-storage: -- code: 0x70, key: 0x2, ASC: 0x3a, ASCQ: 0x0 > > > usb-storage: Not Ready: media not present > > > usb-storage: scsi cmd done, result=0x2 > > > usb-storage: *** thread sleeping. > > > sde: Unit Not Ready, sense: > > > Current 00:00: sense key Not Ready > > > Additional sense indicates Medium not present > > > usb-storage: queuecommand() called > > > usb-storage: *** thread awakened. > > > usb-storage: Command READ_CAPACITY (10 bytes) > > > usb-storage: 25 60 00 00 00 00 00 00 00 00 16 c0 > > > usb-storage: Bulk command S 0x43425355 T 0x249 Trg 0 LUN 3 L 8 F 128 CL > > > 10 > > > usb-storage: Bulk command transfer result=0 > > > usb-storage: usb_stor_transfer_partial(): xfer 8 bytes > > > usb-storage: usb_stor_bulk_msg() returned -32 xferred 0/8 > > > usb-storage: clearing endpoint halt for pipe 0xc0008280 > > > usb-storage: usb_stor_clear_halt: result=0 > > > usb-storage: usb_stor_transfer_partial(): unknown error > > > usb-storage: Bulk data transfer result 0x2 > > > usb-storage: Attempting to get CSW... > > > usb-storage: Bulk status result = 0 > > > usb-storage: Bulk status Sig 0x53425355 T 0x249 R 8 Stat 0x1 > > > usb-storage: -- transport indicates command failure > > > usb-storage: Issuing auto-REQUEST_SENSE > > > usb-storage: Bulk command S 0x43425355 T 0x24a Trg 0 LUN 3 L 18 F 128 CL > > > 6 > > > usb-storage: Bulk command transfer result=0 > > > usb-storage: usb_stor_transfer_partial(): xfer 18 bytes > > > usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18 > > > usb-storage: usb_stor_transfer_partial(): transfer complete > > > usb-storage: Bulk data transfer result 0x0 > > > usb-storage: Attempting to get CSW... > > > usb-storage: Bulk status result = 0 > > > usb-storage: Bulk status Sig 0x53425355 T 0x24a R 0 Stat 0x0 > > > usb-storage: -- Result from auto-sense is 0 > > > usb-storage: -- code: 0x70, key: 0x2, ASC: 0x3a, ASCQ: 0x0 > > > usb-storage: Not Ready: media not present > > > usb-storage: scsi cmd done, result=0x2 > > > usb-storage: *** thread sleeping. > > > usb-storage: queuecommand() called > > > usb-storage: *** thread awakened. > > > usb-storage: Command READ_CAPACITY (10 bytes) > > > usb-storage: 25 60 00 00 00 00 00 00 00 00 16 c0 > > > usb-storage: Bulk command S 0x43425355 T 0x24b Trg 0 LUN 3 L 8 F 128 CL > > > 10 > > > usb-storage: Bulk command transfer result=0 > > > usb-storage: usb_stor_transfer_partial(): xfer 8 bytes > > > usb-storage: usb_stor_bulk_msg() returned -32 xferred 0/8 > > > usb-storage: clearing endpoint halt for pipe 0xc0008280 > > > usb-storage: usb_stor_clear_halt: result=0 > > > usb-storage: usb_stor_transfer_partial(): unknown error > > > usb-storage: Bulk data transfer result 0x2 > > > usb-storage: Attempting to get CSW... > > > usb-storage: Bulk status result = 0 > > > usb-storage: Bulk status Sig 0x53425355 T 0x24b R 8 Stat 0x1 > > > usb-storage: -- transport indicates command failure > > > usb-storage: Issuing auto-REQUEST_SENSE > > > usb-storage: Bulk command S 0x43425355 T 0x24c Trg 0 LUN 3 L 18 F 128 CL > > > 6 > > > usb-storage: Bulk command transfer result=0 > > > usb-storage: usb_stor_transfer_partial(): xfer 18 bytes > > > usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18 > > > usb-storage: usb_stor_transfer_partial(): transfer complete > > > usb-storage: Bulk data transfer result 0x0 > > > usb-storage: Attempting to get CSW... > > > usb-storage: Bulk status result = 0 > > > usb-storage: Bulk status Sig 0x53425355 T 0x24c R 0 Stat 0x0 > > > usb-storage: -- Result from auto-sense is 0 > > > usb-storage: -- code: 0x70, key: 0x2, ASC: 0x3a, ASCQ: 0x0 > > > usb-storage: Not Ready: media not present > > > usb-storage: scsi cmd done, result=0x2 > > > usb-storage: *** thread sleeping. > > > usb-storage: queuecommand() called > > > usb-storage: *** thread awakened. > > > usb-storage: Command READ_CAPACITY (10 bytes) > > > usb-storage: 25 60 00 00 00 00 00 00 00 00 16 c0 > > > usb-storage: Bulk command S 0x43425355 T 0x24d Trg 0 LUN 3 L 8 F 128 CL > > > 10 > > > usb-storage: Bulk command transfer result=0 > > > usb-storage: usb_stor_transfer_partial(): xfer 8 bytes > > > usb-storage: usb_stor_bulk_msg() returned -32 xferred 0/8 > > > usb-storage: clearing endpoint halt for pipe 0xc0008280 > > > usb-storage: usb_stor_clear_halt: result=0 > > > usb-storage: usb_stor_transfer_partial(): unknown error > > > usb-storage: Bulk data transfer result 0x2 > > > usb-storage: Attempting to get CSW... > > > usb-storage: Bulk status result = 0 > > > usb-storage: Bulk status Sig 0x53425355 T 0x24d R 8 Stat 0x1 > > > usb-storage: -- transport indicates command failure > > > usb-storage: Issuing auto-REQUEST_SENSE > > > usb-storage: Bulk command S 0x43425355 T 0x24e Trg 0 LUN 3 L 18 F 128 CL > > > 6 > > > usb-storage: Bulk command transfer result=0 > > > usb-storage: usb_stor_transfer_partial(): xfer 18 bytes > > > usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18 > > > usb-storage: usb_stor_transfer_partial(): transfer complete > > > usb-storage: Bulk data transfer result 0x0 > > > usb-storage: Attempting to get CSW... > > > usb-storage: Bulk status result = 0 > > > usb-storage: Bulk status Sig 0x53425355 T 0x24e R 0 Stat 0x0 > > > usb-storage: -- Result from auto-sense is 0 > > > usb-storage: -- code: 0x70, key: 0x2, ASC: 0x3a, ASCQ: 0x0 > > > usb-storage: Not Ready: media not present > > > usb-storage: scsi cmd done, result=0x2 > > > usb-storage: *** thread sleeping. > > > sde : READ CAPACITY failed. > > > sde : status = 1, message = 00, host = 0, driver = 08 > > > Current sd00:00: sense key Not Ready > > > Additional sense indicates Medium not present > > > sde : block size assumed to be 512 bytes, disk size 1GB. > > > usb-storage: queuecommand() called > > > usb-storage: *** thread awakened. > > > usb-storage: Command MODE_SENSE (6 bytes) > > > usb-storage: 1a 60 3f 00 ff 00 00 00 00 00 16 c0 > > > usb-storage: Bulk command S 0x43425355 T 0x24f Trg 0 LUN 3 L 255 F 128 > > > CL 6 > > > usb-storage: Bulk command transfer result=0 > > > usb-storage: usb_stor_transfer_partial(): xfer 255 bytes > > > usb-storage: usb_stor_bulk_msg() returned -32 xferred 0/255 > > > usb-storage: clearing endpoint halt for pipe 0xc0008280 > > > usb-storage: usb_stor_clear_halt: result=0 > > > usb-storage: usb_stor_transfer_partial(): unknown error > > > usb-storage: Bulk data transfer result 0x2 > > > usb-storage: Attempting to get CSW... > > > usb-storage: Bulk status result = 0 > > > usb-storage: Bulk status Sig 0x53425355 T 0x24f R 255 Stat 0x1 > > > usb-storage: -- transport indicates command failure > > > usb-storage: Issuing auto-REQUEST_SENSE > > > usb-storage: Bulk command S 0x43425355 T 0x250 Trg 0 LUN 3 L 18 F 128 CL > > > 6 > > > usb-storage: Bulk command transfer result=0 > > > usb-storage: usb_stor_transfer_partial(): xfer 18 bytes > > > usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18 > > > usb-storage: usb_stor_transfer_partial(): transfer complete > > > usb-storage: Bulk data transfer result 0x0 > > > usb-storage: Attempting to get CSW... > > > usb-storage: Bulk status result = 0 > > > usb-storage: Bulk status Sig 0x53425355 T 0x250 R 0 Stat 0x0 > > > usb-storage: -- Result from auto-sense is 0 > > > usb-storage: -- code: 0x70, key: 0x2, ASC: 0x3a, ASCQ: 0x0 > > > usb-storage: Not Ready: media not present > > > usb-storage: scsi cmd done, result=0x2 > > > usb-storage: *** thread sleeping. > > > sde: test WP failed, assume Write Enabled > > > sde: I/O error: dev 08:40, sector 0 > > > I/O error: dev 08:40, sector 0 > > > unable to read partition table > > > usb-storage: queuecommand() called > > > usb-storage: *** thread awakened. > > > usb-storage: Command ALLOW_MEDIUM_REMOVAL (6 bytes) > > > usb-storage: 1e 60 00 00 01 00 00 00 54 21 15 c0 > > > usb-storage: Bulk command S 0x43425355 T 0x251 Trg 0 LUN 3 L 0 F 0 CL 6 > > > usb-storage: Bulk command transfer result=0 > > > usb-storage: Attempting to get CSW... > > > usb-storage: Bulk status result = 0 > > > usb-storage: Bulk status Sig 0x53425355 T 0x251 R 0 Stat 0x1 > > > usb-storage: -- transport indicates command failure > > > usb-storage: Issuing auto-REQUEST_SENSE > > > usb-storage: Bulk command S 0x43425355 T 0x252 Trg 0 LUN 3 L 18 F 128 CL > > > 6 > > > usb-storage: Bulk command transfer result=0 > > > usb-storage: usb_stor_transfer_partial(): xfer 18 bytes > > > usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18 > > > usb-storage: usb_stor_transfer_partial(): transfer complete > > > usb-storage: Bulk data transfer result 0x0 > > > usb-storage: Attempting to get CSW... > > > usb-storage: Bulk status result = 0 > > > usb-storage: Bulk status Sig 0x53425355 T 0x252 R 0 Stat 0x0 > > > usb-storage: -- Result from auto-sense is 0 > > > usb-storage: -- code: 0x70, key: 0x2, ASC: 0x3a, ASCQ: 0x0 > > > usb-storage: Not Ready: media not present > > > usb-storage: scsi cmd done, result=0x2 > > > usb-storage: *** thread sleeping. > > > Device not ready. Make sure there is a disc in the drive. > > > usb-storage: queuecommand() called > > > usb-storage: *** thread awakened. > > > usb-storage: Command ALLOW_MEDIUM_REMOVAL (6 bytes) > > > usb-storage: 1e 60 00 00 00 00 00 00 04 00 00 00 > > > usb-storage: Bulk command S 0x43425355 T 0x253 Trg 0 LUN 3 L 0 F 0 CL 6 > > > usb-storage: Bulk command transfer result=0 > > > usb-storage: Attempting to get CSW... > > > usb-storage: Bulk status result = 0 > > > usb-storage: Bulk status Sig 0x53425355 T 0x253 R 0 Stat 0x1 > > > usb-storage: -- transport indicates command failure > > > usb-storage: Issuing auto-REQUEST_SENSE > > > usb-storage: Bulk command S 0x43425355 T 0x254 Trg 0 LUN 3 L 18 F 128 CL > > > 6 > > > usb-storage: Bulk command transfer result=0 > > > usb-storage: usb_stor_transfer_partial(): xfer 18 bytes > > > usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18 > > > usb-storage: usb_stor_transfer_partial(): transfer complete > > > usb-storage: Bulk data transfer result 0x0 > > > usb-storage: Attempting to get CSW... > > > usb-storage: Bulk status result = 0 > > > usb-storage: Bulk status Sig 0x53425355 T 0x254 R 0 Stat 0x0 > > > usb-storage: -- Result from auto-sense is 0 > > > usb-storage: -- code: 0x70, key: 0x2, ASC: 0x3a, ASCQ: 0x0 > > > usb-storage: Not Ready: media not present > > > usb-storage: scsi cmd done, result=0x2 > > > usb-storage: *** thread sleeping. > > > Device not ready. Make sure there is a disc in the drive. > > > > > > What should I try or do ? > > > > > > Many thanks, > > > Optimized > > > > > > > > > > > > > > > -- > > > SF.Net is sponsored by: Speed Start Your Linux Apps Now. > > > Build and deploy apps & Web services for Linux with > > > a free DVD software kit from IBM. Click Now! > > > http://ads.osdn.com/?ad_id=1356&alloc_id=3438&op=click > > > _______________________________________________ > > > [EMAIL PROTECTED] > > > To unsubscribe, use the last form field at: > > > https://lists.sourceforge.net/lists/listinfo/linux-usb-users > > > > > > > -- > > /--+--\ > > |Stephen J. Gowdy | SLAC, MailStop 34, | > > |http://www.slac.stanford.edu/~gowdy/ | 2575 Sand Hill Road, | > > |http://calendar.yahoo.com/gowdy | Menlo Park CA 94025, USA | > > |EMail: [EMAIL PROTECTED] | Tel: +1 650 926 3144 | > > \--+--/ > > > > > > -- > > SF.Net is sponsored by: Speed Start Your Linux Apps Now. > > Build and deploy apps & Web services for Linux with > > a free DVD software kit from IBM. Click Now! > > http://ads.osdn.com/?ad_id=1356&alloc_id=3438&op=click > > _______________________________________________ > > [EMAIL PROTECTED] > > To unsubscribe, use the last form field at: > > https://lists.sourceforge.net/lists/listinfo/linux-usb-users > -- /------------------------------------+-------------------------\ |Stephen J. Gowdy | SLAC, MailStop 34, | |http://www.slac.stanford.edu/~gowdy/ | 2575 Sand Hill Road, | |http://calendar.yahoo.com/gowdy | Menlo Park CA 94025, USA | |EMail: [EMAIL PROTECTED] | Tel: +1 650 926 3144 | \------------------------------------+-------------------------/ ------------------------------------------------------- SF.Net is sponsored by: Speed Start Your Linux Apps Now. Build and deploy apps & Web services for Linux with a free DVD software kit from IBM. Click Now! http://ads.osdn.com/?ad_id=1356&alloc_id=3438&op=click _______________________________________________ [EMAIL PROTECTED] To unsubscribe, use the last form field at: https://lists.sourceforge.net/lists/listinfo/linux-usb-users
