Hi,
OK, it's been a couple of days but I've done what you asked. Here's
/var/log/messages and dmesg after attching the device. I didn't try to
mount a disk.
--- begin dmesg ---
: Thermal Zone [THRM] (36 C)
Console: switching to colour frame buffer device 128x96
pty: 256 Unix98 ptys configured
Real Time Clock Driver v1.12
Non-volatile memory driver v1.2
hw_random hardware driver 1.0.0 loaded
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH3M: IDE controller at PCI slot 0000:00:1f.1
ICH3M: chipset revision 2
ICH3M: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1800-0x1807, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x1808-0x180f, BIOS settings: hdc:DMA, hdd:pio
hda: IC25N030ATCS04-0, ATA DISK drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: QSI CD-RW/DVD-ROM SBW-161, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 58605120 sectors (30005 MB) w/1768KiB Cache, CHS=58140/16/63, UDMA(100)
hda: hda1 hda2
Console: switching to colour frame buffer device 128x96
mice: PS/2 mouse device common for all mice
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI: (supports S0 S3 S4 S5)
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 140k freed
Adding 2096472k swap on /dev/hda2. Priority:-1 extents:1
EXT3 FS on hda1, internal journal
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
Yenta: CardBus bridge found at 0000:01:05.0 [107b:1450]
Yenta: ISA IRQ mask 0x0898, PCI irq 10
Socket status: 30000007
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
inserting floppy driver for 2.6.3
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected an Intel 830M Chipset.
agpgart: Maximum main memory to use for agp memory: 202M
agpgart: Detected 892K stolen memory.
agpgart: AGP aperture is 128M @ 0xe8000000
mtrr: 0xe8000000,0x8000000 overlaps existing 0xe8000000,0x80000
[drm] Initialized i830 1.3.2 20021108 on minor 0
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
lp0: using parport0 (polling).
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
PCI: Enabling device 0000:00:1f.6 (0000 -> 0001)
input: PS/2 Generic Mouse on isa0060/serio1
input: PC Speaker
PCI: Setting latency timer of device 0000:01:03.0 to 64
Intel(R) PRO/100 Network Driver - version 2.3.36-k1
Copyright (c) 2003 Intel Corporation
PCI: Setting latency timer of device 0000:01:08.0 to 64
e100: selftest OK.
e100: eth0: Intel(R) PRO/100 Network Connection
Hardware receive checksums enabled
drivers/usb/core/usb.c: registered new driver usbfs
drivers/usb/core/usb.c: registered new driver hub
drivers/usb/host/uhci-hcd.c: USB Universal Host Controller Interface driver v2.1
uhci_hcd 0000:00:1d.0: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: irq 10, io base 00001840
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
drivers/usb/host/uhci-hcd.c: detected 2 ports
uhci_hcd 0000:00:1d.0: root hub device address 1
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
drivers/usb/core/message.c: USB device number 1 default language ID 0x409
usb usb1: Product: UHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.3 uhci_hcd
usb usb1: SerialNumber: 0000:00:1d.0
drivers/usb/core/usb.c: usb_hotplug
usb usb1: registering 1-0:1.0 (config #1, interface 0)
drivers/usb/core/usb.c: usb_hotplug
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: ganged power switching
hub 1-0:1.0: global over-current protection
hub 1-0:1.0: Port indicators are not supported
hub 1-0:1.0: power on to power good time: 2ms
hub 1-0:1.0: hub controller current requirement: 0mA
hub 1-0:1.0: local power source is good
hub 1-0:1.0: no over-current condition exists
hub 1-0:1.0: enabling power on all ports
uhci_hcd 0000:00:1d.1: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: irq 10, io base 00001860
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
drivers/usb/host/uhci-hcd.c: detected 2 ports
uhci_hcd 0000:00:1d.1: root hub device address 1
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
drivers/usb/core/message.c: USB device number 1 default language ID 0x409
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.3 uhci_hcd
usb usb2: SerialNumber: 0000:00:1d.1
drivers/usb/core/usb.c: usb_hotplug
usb usb2: registering 2-0:1.0 (config #1, interface 0)
drivers/usb/core/usb.c: usb_hotplug
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: ganged power switching
hub 2-0:1.0: global over-current protection
hub 2-0:1.0: Port indicators are not supported
hub 2-0:1.0: power on to power good time: 2ms
hub 2-0:1.0: hub controller current requirement: 0mA
hub 2-0:1.0: local power source is good
hub 2-0:1.0: no over-current condition exists
hub 2-0:1.0: enabling power on all ports
hub 1-0:1.0: port 2, status 301, change 1, 1.5 Mb/s
hub 1-0:1.0: debounce: port 2: delay 100ms stable 4 status 0x301
usb 1-2: new low speed USB device using address 2
usb 1-2: new device strings: Mfr=1, Product=2, SerialNumber=0
drivers/usb/core/message.c: USB device number 2 default language ID 0x409
usb 1-2: Product: USB-PS/2 Optical Mouse
usb 1-2: Manufacturer: Logitech
drivers/usb/core/usb.c: usb_hotplug
usb 1-2: registering 1-2:1.0 (config #1, interface 0)
drivers/usb/core/usb.c: usb_hotplug
drivers/usb/host/uhci-hcd.c: 1860: suspend_hc
e100: eth0 NIC Link is Up 10 Mbps Half duplex
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0800-0x08ff: excluding 0x800-0x80f
cs: IO port probe 0x0100-0x04ff: excluding 0x200-0x207 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
drivers/usb/core/usb.c: registered new driver hiddev
hid 1-2:1.0: usb_probe_interface
hid 1-2:1.0: usb_probe_interface - got id
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1d.0-2
drivers/usb/core/usb.c: registered new driver hid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02f7fe0(lo)
IPv6 over IPv4 tunneling driver
mtrr: 0xe8000000,0x8000000 overlaps existing 0xe8000000,0x80000
eth0: no IPv6 routers present
atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0).
atkbd.c: This is an XFree86 bug. It shouldn't access hardware directly.
atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0).
atkbd.c: This is an XFree86 bug. It shouldn't access hardware directly.
mtrr: 0xe8000000,0x8000000 overlaps existing 0xe8000000,0x80000
atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0).
atkbd.c: This is an XFree86 bug. It shouldn't access hardware directly.
atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0).
atkbd.c: This is an XFree86 bug. It shouldn't access hardware directly.
mtrr: 0xe8000000,0x8000000 overlaps existing 0xe8000000,0x80000
atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0).
atkbd.c: This is an XFree86 bug. It shouldn't access hardware directly.
atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0).
atkbd.c: This is an XFree86 bug. It shouldn't access hardware directly.
hub 1-0:1.0: port 1, status 101, change 1, 12 Mb/s
hub 1-0:1.0: debounce: port 1: delay 100ms stable 4 status 0x101
usb 1-1: new full speed USB device using address 3
usb 1-1: new device strings: Mfr=1, Product=2, SerialNumber=0
drivers/usb/core/message.c: USB device number 3 default language ID 0x409
usb 1-1: Product: eUSB ATA / ATAPI Adapter
usb 1-1: Manufacturer: SCM Microsystems Inc.
drivers/usb/core/usb.c: usb_hotplug
usb 1-1: registering 1-1:1.0 (config #1, interface 0)
drivers/usb/core/usb.c: usb_hotplug
SCSI subsystem initialized
Initializing USB Mass Storage driver...
usb-storage 1-1:1.0: usb_probe_interface
usb-storage 1-1:1.0: usb_probe_interface - got id
usb-storage: USB Mass Storage device detected
usb-storage: act_altsetting is 0, id_index is 27
usb-storage: -- associate_dev
usb-storage: Vendor: Shuttle
usb-storage: Product: CD-RW Device
usb-storage: Transport: Bulk
usb-storage: Protocol: 8020i
usb-storage: Endpoints: In: 0xc9c30874 Out: 0xc9c30860 Int: 0xc9c30888 (Period 32)
usb-storage: usb_stor_control_msg: rq=fe rqtype=a1 value=0000 index=00 len=1
usb-storage: GetMaxLUN command result is -32, data is 0
usb-storage: *** thread sleeping.
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command INQUIRY (6 bytes)
usb-storage: 12 00 00 00 24 00
usb-storage: Bulk Command S 0x43425355 T 0x1 L 36 F 128 Trg 0 LUN 0 CL 12
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code -32; transferred 31/31
usb-storage: clearing endpoint halt for pipe 0xc0008300
usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=01 len=0
drivers/usb/host/uhci-hcd.c: uhci_result_control() failed with status 440000
[cf3a92a0] link (0f3a91e2) element (0f82e0c0)
0: [cf82e0c0] link (0f82e100) e0 Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0
Dev=3, PID=2d(SETUP) (buf=0f1d10a0)
1: [cf82e100] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=3,
PID=69(IN) (buf=00000000)
usb-storage: usb_stor_clear_halt: result = -110
usb-storage: Bulk command transfer result=4
usb-storage: -- transport indicates error, resetting
usb-storage: usb_stor_Bulk_reset called
usb-storage: usb_stor_control_msg: rq=ff rqtype=21 value=0000 index=00 len=0
drivers/usb/host/uhci-hcd.c: uhci_result_control() failed with status 440000
[cf3a9270] link (0f3a91e2) element (0f82e080)
0: [cf82e080] link (0f82e140) e0 Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0
Dev=3, PID=2d(SETUP) (buf=0f1d10a0)
1: [cf82e140] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=3,
PID=69(IN) (buf=00000000)
usb-storage: Soft reset failed: -110
usb-storage: scsi cmd done, result=0x70000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command INQUIRY (6 bytes)
usb-storage: 12 00 00 00 24 00
usb-storage: Bulk Command S 0x43425355 T 0x2 L 36 F 128 Trg 0 LUN 0 CL 12
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code -32; transferred 31/31
usb-storage: clearing endpoint halt for pipe 0xc0008300
usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=01 len=0
drivers/usb/host/uhci-hcd.c: uhci_result_control() failed with status 440000
[cf3a9270] link (0f3a91e2) element (0f82e080)
0: [cf82e080] link (0f82e100) e0 Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0
Dev=3, PID=2d(SETUP) (buf=0f1d10a0)
1: [cf82e100] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=3,
PID=69(IN) (buf=00000000)
usb-storage: usb_stor_clear_halt: result = -110
usb-storage: Bulk command transfer result=4
usb-storage: -- transport indicates error, resetting
usb-storage: usb_stor_Bulk_reset called
usb-storage: usb_stor_control_msg: rq=ff rqtype=21 value=0000 index=00 len=0
drivers/usb/host/uhci-hcd.c: uhci_result_control() failed with status 440000
[cf3a92a0] link (0f3a91e2) element (0f82e0c0)
0: [cf82e0c0] link (0f82e140) e0 Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0
Dev=3, PID=2d(SETUP) (buf=0f1d10a0)
1: [cf82e140] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=3,
PID=69(IN) (buf=00000000)
usb-storage: Soft reset failed: -110
usb-storage: scsi cmd done, result=0x70000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command INQUIRY (6 bytes)
usb-storage: 12 00 00 00 24 00
usb-storage: Bulk Command S 0x43425355 T 0x3 L 36 F 128 Trg 0 LUN 0 CL 12
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code -32; transferred 31/31
usb-storage: clearing endpoint halt for pipe 0xc0008300
usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=01 len=0
drivers/usb/host/uhci-hcd.c: uhci_result_control() failed with status 440000
[cf3a92a0] link (0f3a91e2) element (0f82e0c0)
0: [cf82e0c0] link (0f82e100) e0 Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0
Dev=3, PID=2d(SETUP) (buf=0f1d10a0)
1: [cf82e100] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=3,
PID=69(IN) (buf=00000000)
usb-storage: usb_stor_clear_halt: result = -110
usb-storage: Bulk command transfer result=4
usb-storage: -- transport indicates error, resetting
usb-storage: usb_stor_Bulk_reset called
usb-storage: usb_stor_control_msg: rq=ff rqtype=21 value=0000 index=00 len=0
drivers/usb/host/uhci-hcd.c: uhci_result_control() failed with status 440000
[cf3a9270] link (0f3a91e2) element (0f82e080)
0: [cf82e080] link (0f82e140) e0 Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0
Dev=3, PID=2d(SETUP) (buf=0f1d10a0)
1: [cf82e140] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=3,
PID=69(IN) (buf=00000000)
usb-storage: Soft reset failed: -110
usb-storage: scsi cmd done, result=0x70000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (1:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (2:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (3:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (4:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (5:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (6:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (7:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 3
drivers/usb/core/usb.c: registered new driver usb-storage
USB Mass Storage support registered.
--- end dmesg ---
--- begin /var/log/messages ---
Mar 6 13:07:46 localhost kernel: atkbd.c: Unknown key released (translated set 2,
code 0x7a on isa0060/serio0).
Mar 6 13:07:46 localhost kernel: atkbd.c: This is an XFree86 bug. It shouldn't access
hardware directly.
Mar 6 13:07:46 localhost kernel: atkbd.c: Unknown key released (translated set 2,
code 0x7a on isa0060/serio0).
Mar 6 13:07:46 localhost kernel: atkbd.c: This is an XFree86 bug. It shouldn't access
hardware directly.
Mar 6 13:09:10 localhost gconfd (kipp-1625): GConf server is not in use, shutting
down.
Mar 6 13:09:10 localhost gconfd (kipp-1625): Exiting
Mar 6 13:09:50 localhost gconfd (kipp-1812): starting (version 2.4.0.1), pid 1812
user 'kipp'
Mar 6 13:09:50 localhost gconfd (kipp-1812): Resolved address
"xml:readonly:/etc/gconf/gconf.xml.mandatory" to a read-only config source at position 0
Mar 6 13:09:50 localhost gconfd (kipp-1812): Resolved address
"xml:readwrite:/home/kipp/.gconf" to a writable config source at position 1
Mar 6 13:09:50 localhost gconfd (kipp-1812): Resolved address
"xml:readonly:/etc/gconf/gconf.xml.defaults" to a read-only config source at position 2
Mar 6 13:10:21 localhost kernel: usb 1-1: new full speed USB device using address 3
Mar 6 13:10:21 localhost kernel: usb 1-1: Product: eUSB ATA / ATAPI Adapter
Mar 6 13:10:21 localhost kernel: usb 1-1: Manufacturer: SCM Microsystems Inc.
Mar 6 13:10:22 localhost kernel: SCSI subsystem initialized
Mar 6 13:10:22 localhost kernel: Initializing USB Mass Storage driver...
Mar 6 13:10:22 localhost kernel: scsi0 : SCSI emulation for USB Mass Storage devices
Mar 6 13:10:22 localhost kernel: [cf3a92a0] link (0f3a91e2) element (0f82e0c0)
Mar 6 13:10:22 localhost kernel: 0: [cf82e0c0] link (0f82e100) e0 Stalled CRC/Timeo
Length=7 MaxLen=7 DT0 EndPt=0 Dev=3, PID=2d(SETUP) (buf=0f1d10a0)
Mar 6 13:10:22 localhost kernel: 1: [cf82e100] link (00000001) e3 IOC Active
Length=0 MaxLen=7ff DT1 EndPt=0 Dev=3, PID=69(IN) (buf=00000000)
Mar 6 13:10:22 localhost kernel:
Mar 6 13:10:22 localhost kernel: [cf3a9270] link (0f3a91e2) element (0f82e080)
Mar 6 13:10:22 localhost kernel: 0: [cf82e080] link (0f82e140) e0 Stalled CRC/Timeo
Length=7 MaxLen=7 DT0 EndPt=0 Dev=3, PID=2d(SETUP) (buf=0f1d10a0)
Mar 6 13:10:22 localhost kernel: 1: [cf82e140] link (00000001) e3 IOC Active
Length=0 MaxLen=7ff DT1 EndPt=0 Dev=3, PID=69(IN) (buf=00000000)
Mar 6 13:10:22 localhost kernel:
Mar 6 13:10:22 localhost kernel: [cf3a9270] link (0f3a91e2) element (0f82e080)
Mar 6 13:10:22 localhost kernel: 0: [cf82e080] link (0f82e100) e0 Stalled CRC/Timeo
Length=7 MaxLen=7 DT0 EndPt=0 Dev=3, PID=2d(SETUP) (buf=0f1d10a0)
Mar 6 13:10:22 localhost kernel: 1: [cf82e100] link (00000001) e3 IOC Active
Length=0 MaxLen=7ff DT1 EndPt=0 Dev=3, PID=69(IN) (buf=00000000)
Mar 6 13:10:22 localhost kernel:
Mar 6 13:10:22 localhost kernel: [cf3a92a0] link (0f3a91e2) element (0f82e0c0)
Mar 6 13:10:22 localhost kernel: 0: [cf82e0c0] link (0f82e140) e0 Stalled CRC/Timeo
Length=7 MaxLen=7 DT0 EndPt=0 Dev=3, PID=2d(SETUP) (buf=0f1d10a0)
Mar 6 13:10:22 localhost kernel: 1: [cf82e140] link (00000001) e3 IOC Active
Length=0 MaxLen=7ff DT1 EndPt=0 Dev=3, PID=69(IN) (buf=00000000)
Mar 6 13:10:22 localhost kernel:
Mar 6 13:10:22 localhost kernel: [cf3a92a0] link (0f3a91e2) element (0f82e0c0)
Mar 6 13:10:22 localhost kernel: 0: [cf82e0c0] link (0f82e100) e0 Stalled CRC/Timeo
Length=7 MaxLen=7 DT0 EndPt=0 Dev=3, PID=2d(SETUP) (buf=0f1d10a0)
Mar 6 13:10:22 localhost kernel: 1: [cf82e100] link (00000001) e3 IOC Active
Length=0 MaxLen=7ff DT1 EndPt=0 Dev=3, PID=69(IN) (buf=00000000)
Mar 6 13:10:22 localhost kernel:
Mar 6 13:10:22 localhost kernel: [cf3a9270] link (0f3a91e2) element (0f82e080)
Mar 6 13:10:22 localhost kernel: 0: [cf82e080] link (0f82e140) e0 Stalled CRC/Timeo
Length=7 MaxLen=7 DT0 EndPt=0 Dev=3, PID=2d(SETUP) (buf=0f1d10a0)
Mar 6 13:10:22 localhost kernel: 1: [cf82e140] link (00000001) e3 IOC Active
Length=0 MaxLen=7ff DT1 EndPt=0 Dev=3, PID=69(IN) (buf=00000000)
Mar 6 13:10:22 localhost kernel:
Mar 6 13:10:22 localhost kernel: drivers/usb/core/usb.c: registered new driver
usb-storage
Mar 6 13:10:22 localhost kernel: USB Mass Storage support registered.
--- end /var/log/messages ---
On Wed, 3 Mar 2004, Matthew Dharm wrote:
> About the only thing I can suggest is this:
>
> Located the entry for 0x4e6/0x0101 in drivers/usb/storage/unusual_devs.h
> and change the US_PR_CB to US_PR_BULK and see if that makes a difference.
>
> Other than that, I don't know what else to say...
>
> Matt
>
> On Tue, Mar 02, 2004 at 10:50:42PM -0500, Kipp Cannon wrote:
> > Oooo... sounds bad :-P. Here's /proc/usb/devices
> >
> > -Kipp
> >
> > --- begin devices ---
> >
> > T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
> > B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
> > D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
> > P: Vendor=0000 ProdID=0000 Rev= 2.06
> > S: Manufacturer=Linux 2.6.3 uhci_hcd
> > S: Product=UHCI Host Controller
> > S: SerialNumber=0000:00:1d.1
> > C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA
> > I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
> > E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
> >
> > T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
> > B: Alloc= 93/900 us (10%), #Int= 1, #Iso= 0
> > D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
> > P: Vendor=0000 ProdID=0000 Rev= 2.06
> > S: Manufacturer=Linux 2.6.3 uhci_hcd
> > S: Product=UHCI Host Controller
> > S: SerialNumber=0000:00:1d.0
> > C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA
> > I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
> > E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
> >
> > T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
> > D: Ver= 1.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
> > P: Vendor=04e6 ProdID=0101 Rev= 2.00
> > S: Manufacturer=SCM Microsystems Inc.
> > S: Product=eUSB ATA / ATAPI Adapter
> > C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA
> > I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=usb-storage
> > E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
> > E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
> > E: Ad=83(I) Atr=03(Int.) MxPS= 2 Ivl=32ms
> >
> > T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 2 Spd=1.5 MxCh= 0
> > D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
> > P: Vendor=046d ProdID=c00e Rev=11.10
> > S: Manufacturer=Logitech
> > S: Product=USB-PS/2 Optical Mouse
> > C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr= 98mA
> > I: If#= 0 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=01 Prot=02 Driver=hid
> > E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=10ms
> > --- end devices ---
> >
> > On Tue, 2 Mar 2004, Matthew Dharm wrote:
> >
> > > Wow... there isn't a single command in here which actually worked.
> > >
> > > Tho, it's nice to see that the code we've got is pretty bulletproof with
> > > really bogus devices (many thanks to Alan Stern who really worked on a lot
> > > of that).
> > >
> > > What does /proc/bus/usb/devices show when the unit is attached?
> > >
> > > Matt
> > >
> > > On Tue, Mar 02, 2004 at 01:24:04PM -0500, Kipp Cannon wrote:
> > > > Hi,
> > > >
> > > > OK, I've recompiled with verbose debugging enabled, rebooted the system,
> > > > plugged in the drive and attempted to mount the disk that's in it. The
> > > > following is the entire output of dmesg following the (failed) mount
> > > > attempt. I decided not to second guess what it is that you need from
> > > > this, so I've just included the whole thing. (/var/log/messages has the
> > > > same stuff as before in it)
> > > >
> > > > -Kipp
> > > >
> > > > --- begin dmesg.log ---
> > > > TCP: Hash tables configured (established 16384 bind 32768)
> > > > NET: Registered protocol family 1
> > > > NET: Registered protocol family 17
> > > > ACPI: (supports S0 S3 S4 S5)
> > > > kjournald starting. Commit interval 5 seconds
> > > > EXT3-fs: mounted filesystem with ordered data mode.
> > > > VFS: Mounted root (ext3 filesystem) readonly.
> > > > Freeing unused kernel memory: 140k freed
> > > > Adding 2096472k swap on /dev/hda2. Priority:-1 extents:1
> > > > EXT3 FS on hda1, internal journal
> > > > Linux Kernel Card Services
> > > > options: [pci] [cardbus] [pm]
> > > > Yenta: CardBus bridge found at 0000:01:05.0 [107b:1450]
> > > > Yenta: ISA IRQ mask 0x0898, PCI irq 10
> > > > Socket status: 30000007
> > > > hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
> > > > Uniform CD-ROM driver Revision: 3.20
> > > > inserting floppy driver for 2.6.3
> > > > Floppy drive(s): fd0 is 1.44M
> > > > FDC 0 is a National Semiconductor PC87306
> > > > Linux agpgart interface v0.100 (c) Dave Jones
> > > > agpgart: Detected an Intel 830M Chipset.
> > > > agpgart: Maximum main memory to use for agp memory: 202M
> > > > agpgart: Detected 892K stolen memory.
> > > > agpgart: AGP aperture is 128M @ 0xe8000000
> > > > mtrr: 0xe8000000,0x8000000 overlaps existing 0xe8000000,0x80000
> > > > [drm] Initialized i830 1.3.2 20021108 on minor 0
> > > > parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
> > > > parport0: irq 7 detected
> > > > parport0: cpp_daisy: aa5500ff(38)
> > > > parport0: assign_addrs: aa5500ff(38)
> > > > parport0: cpp_daisy: aa5500ff(38)
> > > > parport0: assign_addrs: aa5500ff(38)
> > > > lp0: using parport0 (polling).
> > > > Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
> > > > ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> > > > PCI: Enabling device 0000:00:1f.6 (0000 -> 0001)
> > > > input: PS/2 Generic Mouse on isa0060/serio1
> > > > input: PC Speaker
> > > > PCI: Setting latency timer of device 0000:01:03.0 to 64
> > > > Intel(R) PRO/100 Network Driver - version 2.3.36-k1
> > > > Copyright (c) 2003 Intel Corporation
> > > >
> > > > PCI: Setting latency timer of device 0000:01:08.0 to 64
> > > > e100: selftest OK.
> > > > e100: eth0: Intel(R) PRO/100 Network Connection
> > > > Hardware receive checksums enabled
> > > >
> > > > drivers/usb/core/usb.c: registered new driver usbfs
> > > > drivers/usb/core/usb.c: registered new driver hub
> > > > drivers/usb/host/uhci-hcd.c: USB Universal Host Controller Interface driver
> > > > v2.1
> > > > uhci_hcd 0000:00:1d.0: UHCI Host Controller
> > > > PCI: Setting latency timer of device 0000:00:1d.0 to 64
> > > > uhci_hcd 0000:00:1d.0: irq 10, io base 00001840
> > > > uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
> > > > drivers/usb/host/uhci-hcd.c: detected 2 ports
> > > > uhci_hcd 0000:00:1d.0: root hub device address 1
> > > > usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
> > > > drivers/usb/core/message.c: USB device number 1 default language ID 0x409
> > > > usb usb1: Product: UHCI Host Controller
> > > > usb usb1: Manufacturer: Linux 2.6.3 uhci_hcd
> > > > usb usb1: SerialNumber: 0000:00:1d.0
> > > > drivers/usb/core/usb.c: usb_hotplug
> > > > usb usb1: registering 1-0:1.0 (config #1, interface 0)
> > > > drivers/usb/core/usb.c: usb_hotplug
> > > > hub 1-0:1.0: usb_probe_interface
> > > > hub 1-0:1.0: usb_probe_interface - got id
> > > > hub 1-0:1.0: USB hub found
> > > > hub 1-0:1.0: 2 ports detected
> > > > hub 1-0:1.0: standalone hub
> > > > hub 1-0:1.0: ganged power switching
> > > > hub 1-0:1.0: global over-current protection
> > > > hub 1-0:1.0: Port indicators are not supported
> > > > hub 1-0:1.0: power on to power good time: 2ms
> > > > hub 1-0:1.0: hub controller current requirement: 0mA
> > > > hub 1-0:1.0: local power source is good
> > > > hub 1-0:1.0: no over-current condition exists
> > > > hub 1-0:1.0: enabling power on all ports
> > > > uhci_hcd 0000:00:1d.1: UHCI Host Controller
> > > > PCI: Setting latency timer of device 0000:00:1d.1 to 64
> > > > uhci_hcd 0000:00:1d.1: irq 10, io base 00001860
> > > > uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
> > > > drivers/usb/host/uhci-hcd.c: detected 2 ports
> > > > uhci_hcd 0000:00:1d.1: root hub device address 1
> > > > usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
> > > > drivers/usb/core/message.c: USB device number 1 default language ID 0x409
> > > > usb usb2: Product: UHCI Host Controller
> > > > usb usb2: Manufacturer: Linux 2.6.3 uhci_hcd
> > > > usb usb2: SerialNumber: 0000:00:1d.1
> > > > drivers/usb/core/usb.c: usb_hotplug
> > > > usb usb2: registering 2-0:1.0 (config #1, interface 0)
> > > > drivers/usb/core/usb.c: usb_hotplug
> > > > hub 2-0:1.0: usb_probe_interface
> > > > hub 2-0:1.0: usb_probe_interface - got id
> > > > hub 2-0:1.0: USB hub found
> > > > hub 2-0:1.0: 2 ports detected
> > > > hub 2-0:1.0: standalone hub
> > > > hub 2-0:1.0: ganged power switching
> > > > hub 2-0:1.0: global over-current protection
> > > > hub 2-0:1.0: Port indicators are not supported
> > > > hub 2-0:1.0: power on to power good time: 2ms
> > > > hub 2-0:1.0: hub controller current requirement: 0mA
> > > > hub 2-0:1.0: local power source is good
> > > > hub 2-0:1.0: no over-current condition exists
> > > > hub 2-0:1.0: enabling power on all ports
> > > > hub 1-0:1.0: port 2, status 301, change 1, 1.5 Mb/s
> > > > hub 1-0:1.0: debounce: port 2: delay 100ms stable 4 status 0x301
> > > > usb 1-2: new low speed USB device using address 2
> > > > usb 1-2: new device strings: Mfr=1, Product=2, SerialNumber=0
> > > > drivers/usb/core/message.c: USB device number 2 default language ID 0x409
> > > > usb 1-2: Product: USB-PS/2 Optical Mouse
> > > > usb 1-2: Manufacturer: Logitech
> > > > drivers/usb/core/usb.c: usb_hotplug
> > > > usb 1-2: registering 1-2:1.0 (config #1, interface 0)
> > > > drivers/usb/core/usb.c: usb_hotplug
> > > > drivers/usb/host/uhci-hcd.c: 1860: suspend_hc
> > > > e100: eth0 NIC Link is Up 10 Mbps Half duplex
> > > > cs: IO port probe 0x0c00-0x0cff: clean.
> > > > cs: IO port probe 0x0800-0x08ff: excluding 0x800-0x80f
> > > > cs: IO port probe 0x0100-0x04ff: excluding 0x200-0x207 0x4d0-0x4d7
> > > > cs: IO port probe 0x0a00-0x0aff: clean.
> > > > NET: Registered protocol family 10
> > > > Disabled Privacy Extensions on device c02f7fe0(lo)
> > > > IPv6 over IPv4 tunneling driver
> > > > drivers/usb/core/usb.c: registered new driver hiddev
> > > > hid 1-2:1.0: usb_probe_interface
> > > > hid 1-2:1.0: usb_probe_interface - got id
> > > > input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on
> > > > usb-0000:00:1d.0-2
> > > > drivers/usb/core/usb.c: registered new driver hid
> > > > drivers/usb/input/hid-core.c: v2.0:USB HID core driver
> > > > mtrr: 0xe8000000,0x8000000 overlaps existing 0xe8000000,0x80000
> > > > atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0).
> > > > atkbd.c: This is an XFree86 bug. It shouldn't access hardware directly.
> > > > atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0).
> > > > atkbd.c: This is an XFree86 bug. It shouldn't access hardware directly.
> > > > eth0: no IPv6 routers present
> > > > hub 1-0:1.0: port 1, status 101, change 1, 12 Mb/s
> > > > hub 1-0:1.0: debounce: port 1: delay 100ms stable 4 status 0x101
> > > > usb 1-1: new full speed USB device using address 3
> > > > usb 1-1: new device strings: Mfr=1, Product=2, SerialNumber=0
> > > > drivers/usb/core/message.c: USB device number 3 default language ID 0x409
> > > > usb 1-1: Product: eUSB ATA / ATAPI Adapter
> > > > usb 1-1: Manufacturer: SCM Microsystems Inc.
> > > > drivers/usb/core/usb.c: usb_hotplug
> > > > usb 1-1: registering 1-1:1.0 (config #1, interface 0)
> > > > drivers/usb/core/usb.c: usb_hotplug
> > > > SCSI subsystem initialized
> > > > Initializing USB Mass Storage driver...
> > > > usb-storage 1-1:1.0: usb_probe_interface
> > > > usb-storage 1-1:1.0: usb_probe_interface - got id
> > > > usb-storage: USB Mass Storage device detected
> > > > usb-storage: act_altsetting is 0, id_index is 27
> > > > usb-storage: -- associate_dev
> > > > usb-storage: Vendor: Shuttle
> > > > usb-storage: Product: CD-RW Device
> > > > usb-storage: Transport: Control/Bulk
> > > > usb-storage: Protocol: 8020i
> > > > usb-storage: Endpoints: In: 0xc9d2e8f4 Out: 0xc9d2e8e0 Int: 0xc9d2e908 (Period
> > > > 32)
> > > > usb-storage: *** thread sleeping.
> > > > scsi0 : SCSI emulation for USB Mass Storage devices
> > > > usb-storage: queuecommand called
> > > > usb-storage: *** thread awakened.
> > > > usb-storage: Command INQUIRY (6 bytes)
> > > > usb-storage: 12 00 00 00 24 00
> > > > usb-storage: usb_stor_ctrl_transfer: rq=00 rqtype=21 value=0000 index=00 len=12
> > > > usb-storage: Status code 0; transferred 12/12
> > > > usb-storage: -- transfer complete
> > > > usb-storage: Call to usb_stor_ctrl_transfer() returned 0
> > > > usb-storage: usb_stor_bulk_transfer_buf: xfer 36 bytes
> > > > usb-storage: Status code -32; transferred 0/36
> > > > usb-storage: clearing endpoint halt for pipe 0xc0010380
> > > > usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=82 len=0
> > > > usb-storage: usb_stor_clear_halt: result = 0
> > > > usb-storage: CB data stage result is 0x2
> > > > usb-storage: -- CB transport device requiring auto-sense
> > > > usb-storage: Issuing auto-REQUEST_SENSE
> > > > usb-storage: usb_stor_ctrl_transfer: rq=00 rqtype=21 value=0000 index=00 len=12
> > > > usb-storage: Status code 0; transferred 12/12
> > > > usb-storage: -- transfer complete
> > > > usb-storage: Call to usb_stor_ctrl_transfer() returned 0
> > > > usb-storage: usb_stor_bulk_transfer_buf: xfer 18 bytes
> > > > usb-storage: Status code -32; transferred 0/18
> > > > usb-storage: clearing endpoint halt for pipe 0xc0010380
> > > > usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=82 len=0
> > > > usb-storage: usb_stor_clear_halt: result = 0
> > > > usb-storage: CB data stage result is 0x2
> > > > usb-storage: -- Result from auto-sense is 0
> > > > usb-storage: -- code: 0x0, key: 0x0, ASC: 0x0, ASCQ: 0x0
> > > > usb-storage: (Unknown Key): (unknown ASC/ASCQ)
> > > > usb-storage: Fixing INQUIRY data to show SCSI rev 2 - was 0
> > > > usb-storage: scsi cmd done, result=0x0
> > > > usb-storage: *** thread sleeping.
> > > > Vendor: Model: Rev:
> > > > Type: Direct-Access ANSI SCSI revision: 02
> > > > usb-storage: queuecommand called
> > > > usb-storage: *** thread awakened.
> > > > usb-storage: Bad LUN (0:1)
> > > > usb-storage: scsi cmd done, result=0x40000
> > > > usb-storage: *** thread sleeping.
> > > > usb-storage: queuecommand called
> > > > usb-storage: *** thread awakened.
> > > > usb-storage: Bad target number (1:0)
> > > > usb-storage: scsi cmd done, result=0x40000
> > > > usb-storage: *** thread sleeping.
> > > > usb-storage: queuecommand called
> > > > usb-storage: *** thread awakened.
> > > > usb-storage: Bad target number (2:0)
> > > > usb-storage: scsi cmd done, result=0x40000
> > > > usb-storage: *** thread sleeping.
> > > > usb-storage: queuecommand called
> > > > usb-storage: *** thread awakened.
> > > > usb-storage: Bad target number (3:0)
> > > > usb-storage: scsi cmd done, result=0x40000
> > > > usb-storage: *** thread sleeping.
> > > > usb-storage: queuecommand called
> > > > usb-storage: *** thread awakened.
> > > > usb-storage: Bad target number (4:0)
> > > > usb-storage: scsi cmd done, result=0x40000
> > > > usb-storage: *** thread sleeping.
> > > > usb-storage: queuecommand called
> > > > usb-storage: *** thread awakened.
> > > > usb-storage: Bad target number (5:0)
> > > > usb-storage: scsi cmd done, result=0x40000
> > > > usb-storage: *** thread sleeping.
> > > > usb-storage: queuecommand called
> > > > usb-storage: *** thread awakened.
> > > > usb-storage: Bad target number (6:0)
> > > > usb-storage: scsi cmd done, result=0x40000
> > > > usb-storage: *** thread sleeping.
> > > > usb-storage: queuecommand called
> > > > usb-storage: *** thread awakened.
> > > > usb-storage: Bad target number (7:0)
> > > > usb-storage: scsi cmd done, result=0x40000
> > > > usb-storage: *** thread sleeping.
> > > > WARNING: USB Mass Storage data integrity not assured
> > > > USB Mass Storage device found at 3
> > > > drivers/usb/core/usb.c: registered new driver usb-storage
> > > > USB Mass Storage support registered.
> > > > usb-storage: queuecommand called
> > > > usb-storage: *** thread awakened.
> > > > usb-storage: Command TEST_UNIT_READY (6 bytes)
> > > > usb-storage: 00 00 00 00 00 00
> > > > usb-storage: usb_stor_ctrl_transfer: rq=00 rqtype=21 value=0000 index=00 len=12
> > > > usb-storage: Status code 0; transferred 12/12
> > > > usb-storage: -- transfer complete
> > > > usb-storage: Call to usb_stor_ctrl_transfer() returned 0
> > > > usb-storage: -- CB transport device requiring auto-sense
> > > > usb-storage: Issuing auto-REQUEST_SENSE
> > > > usb-storage: usb_stor_ctrl_transfer: rq=00 rqtype=21 value=0000 index=00 len=12
> > > > usb-storage: Status code 0; transferred 12/12
> > > > usb-storage: -- transfer complete
> > > > usb-storage: Call to usb_stor_ctrl_transfer() returned 0
> > > > usb-storage: usb_stor_bulk_transfer_buf: xfer 18 bytes
> > > > usb-storage: Status code -32; transferred 0/18
> > > > usb-storage: clearing endpoint halt for pipe 0xc0010380
> > > > usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=82 len=0
> > > > usb-storage: usb_stor_clear_halt: result = 0
> > > > usb-storage: CB data stage result is 0x2
> > > > usb-storage: -- Result from auto-sense is 0
> > > > usb-storage: -- code: 0x0, key: 0x0, ASC: 0x0, ASCQ: 0x0
> > > > usb-storage: (Unknown Key): (unknown ASC/ASCQ)
> > > > usb-storage: scsi cmd done, result=0x0
> > > > usb-storage: *** thread sleeping.
> > > > usb-storage: queuecommand called
> > > > usb-storage: *** thread awakened.
> > > > usb-storage: Command READ_CAPACITY (10 bytes)
> > > > usb-storage: 25 00 00 00 00 00 00 00 00 00
> > > > usb-storage: usb_stor_ctrl_transfer: rq=00 rqtype=21 value=0000 index=00 len=12
> > > > usb-storage: Status code 0; transferred 12/12
> > > > usb-storage: -- transfer complete
> > > > usb-storage: Call to usb_stor_ctrl_transfer() returned 0
> > > > usb-storage: usb_stor_bulk_transfer_buf: xfer 8 bytes
> > > > usb-storage: Status code -32; transferred 0/8
> > > > usb-storage: clearing endpoint halt for pipe 0xc0010380
> > > > usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=82 len=0
> > > > usb-storage: usb_stor_clear_halt: result = 0
> > > > usb-storage: CB data stage result is 0x2
> > > > usb-storage: -- CB transport device requiring auto-sense
> > > > usb-storage: -- unexpectedly short transfer
> > > > usb-storage: Issuing auto-REQUEST_SENSE
> > > > usb-storage: usb_stor_ctrl_transfer: rq=00 rqtype=21 value=0000 index=00 len=12
> > > > usb-storage: Status code 0; transferred 12/12
> > > > usb-storage: -- transfer complete
> > > > usb-storage: Call to usb_stor_ctrl_transfer() returned 0
> > > > usb-storage: usb_stor_bulk_transfer_buf: xfer 18 bytes
> > > > usb-storage: Status code -32; transferred 0/18
> > > > usb-storage: clearing endpoint halt for pipe 0xc0010380
> > > > usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=82 len=0
> > > > usb-storage: usb_stor_clear_halt: result = 0
> > > > usb-storage: CB data stage result is 0x2
> > > > usb-storage: -- Result from auto-sense is 0
> > > > usb-storage: -- code: 0x0, key: 0x0, ASC: 0x0, ASCQ: 0x0
> > > > usb-storage: (Unknown Key): (unknown ASC/ASCQ)
> > > > usb-storage: scsi cmd done, result=0x0
> > > > usb-storage: *** thread sleeping.
> > > > sda : sector size 0 reported, assuming 512.
> > > > SCSI device sda: 1 512-byte hdwr sectors (0 MB)
> > > > sda: assuming drive cache: write through
> > > > sda:<7>usb-storage: queuecommand called
> > > > usb-storage: *** thread awakened.
> > > > usb-storage: Command READ_10 (10 bytes)
> > > > usb-storage: 28 00 00 00 00 00 00 00 01 00
> > > > usb-storage: usb_stor_ctrl_transfer: rq=00 rqtype=21 value=0000 index=00 len=12
> > > > usb-storage: Status code 0; transferred 12/12
> > > > usb-storage: -- transfer complete
> > > > usb-storage: Call to usb_stor_ctrl_transfer() returned 0
> > > > usb-storage: usb_stor_bulk_transfer_sglist: xfer 512 bytes, 1 entries
> > > > usb-storage: Status code -32; transferred 0/512
> > > > usb-storage: clearing endpoint halt for pipe 0xc0010380
> > > > usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=82 len=0
> > > > usb-storage: usb_stor_clear_halt: result = 0
> > > > usb-storage: CB data stage result is 0x2
> > > > usb-storage: -- CB transport device requiring auto-sense
> > > > usb-storage: -- unexpectedly short transfer
> > > > usb-storage: Issuing auto-REQUEST_SENSE
> > > > usb-storage: usb_stor_ctrl_transfer: rq=00 rqtype=21 value=0000 index=00 len=12
> > > > usb-storage: Status code 0; transferred 12/12
> > > > usb-storage: -- transfer complete
> > > > usb-storage: Call to usb_stor_ctrl_transfer() returned 0
> > > > usb-storage: usb_stor_bulk_transfer_buf: xfer 18 bytes
> > > > usb-storage: Status code -32; transferred 0/18
> > > > usb-storage: clearing endpoint halt for pipe 0xc0010380
> > > > usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=82 len=0
> > > > usb-storage: usb_stor_clear_halt: result = 0
> > > > usb-storage: CB data stage result is 0x2
> > > > usb-storage: -- Result from auto-sense is 0
> > > > usb-storage: -- code: 0x0, key: 0x0, ASC: 0x0, ASCQ: 0x0
> > > > usb-storage: (Unknown Key): (unknown ASC/ASCQ)
> > > > usb-storage: scsi cmd done, result=0x0
> > > > usb-storage: *** thread sleeping.
> > > > unknown partition table
> > > > Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
> > > > attempt to access beyond end of device
> > > > sda: rw=0, want=66, limit=1
> > > > isofs_fill_super: bread failed, dev=sda, iso_blknum=16, block=32
> > > > --- end dmesg.log ---
> > > >
> > > >
> > > > On Tue, 2 Mar 2004, Matthew Dharm wrote:
> > > >
> > > > > The device is reporting Direct-Access type, when it should be reporting
> > > > > CD-ROM type.
> > > > >
> > > > > Looking at the logs you provided, actually, it looks like it barely can
> > > > > answer an INQUIRY at all.
> > > > >
> > > > > To get something like this working, you'd have to rewrite the INQUIRY
> > > > > response data to set the type to CD-ROM. Before we go down that path,
> > > > > rebuild the driver with USB Mass Storage Verbose Debug turned on so we can
> > > > > see if something is going wrong with the INQUIRY or (more likely) the
> > > > > device is just busted.
> > > > >
> > > > > Matt
> > > > >
> > > > > On Tue, Mar 02, 2004 at 01:18:29AM -0500, Kipp Cannon wrote:
> > > > > > Hi,
> > > > > >
> > > > > > I've got an external cd-rom drive branded a "Microtech MicroCD" that I'm
> > > > > > having trouble getting to work with Linux 2.6.3 (the only version I've
> > > > > > tried it with). The drive attaches to a USB port on the host machine
> > > > > > through a cable that, at the drive end, has what looks like a "VHDCI"
> > > > > > high-density SCSI connector but is only about half the size.
> > > > > >
> > > > > > usbview reports the drive as a "eUSB ATA/ATAPI adapter" manufactured by
> > > > > > "SCM Microsystems Inc." (vendor/product/rev = 04e6/0101/2.00). Some
> > > > > > searching on Google revealed that SCM Microsystems manufactured a
> > > > > > USB-ATAPI bridge cable that has been used to attach various ATAPI drives
> > > > > > to USB ports, in particular the HP 8200e/8210e CD-Writer Plus.
> > > > > >
> > > > > > I suppose that's what I've got: a parallel-port ATAPI drive that's been
> > > > > > retrofitted to work with USB ports.
> > > > > >
> > > > > > Anyway...
> > > > > >
> > > > > > When I plug in the drive, the usb subsystem loads a bunch of stuff and
> > > > > > sets the drive up on /dev/sda with the following being put in
> > > > > > /var/log/messages
> > > > > >
> > > > > > --- begin /var/log/messages ---
> > > > > > Feb 26 19:44:45 localhost kernel: usb 1-1: new full speed USB device using
> > > > > > address 3
> > > > > > Feb 26 19:44:45 localhost kernel: SCSI subsystem initialized
> > > > > > Feb 26 19:44:45 localhost kernel: Initializing USB Mass Storage driver...
> > > > > > Feb 26 19:44:45 localhost kernel: scsi0 : SCSI emulation for USB Mass
> > > > > > Storage devices
> > > > > > Feb 26 19:44:45 localhost kernel: Vendor: Model:
> > > > > > Rev:
> > > > > > Feb 26 19:44:45 localhost kernel: Type: Direct-Access
> > > > > > ANSI SCSI revision: 02
> > > > > > Feb 26 19:44:45 localhost kernel: drivers/usb/core/usb.c: registered new
> > > > > > driver usb-storage
> > > > > > Feb 26 19:44:45 localhost kernel: USB Mass Storage support registered.
> > > > > > Feb 26 19:44:45 localhost scsi.agent[4486]: disk at
> > > > > > /devices/pci0000:00/0000:00:1d.0/usb1/1-1/1-1:1.0/host0/0:0:0:0
> > > > > > Feb 26 19:44:45 localhost kernel: sda : sector size 0 reported, assuming
> > > > > > 512.
> > > > > > Feb 26 19:44:45 localhost kernel: SCSI device sda: 1 512-byte hdwr sectors
> > > > > > (0 MB)
> > > > > > Feb 26 19:44:45 localhost kernel: sda:<7>usb-storage: queuecommand called
> > > > > > Feb 26 19:44:45 localhost kernel: unknown partition table
> > > > > > Feb 26 19:44:45 localhost kernel: Attached scsi disk sda at scsi0, channel
> > > > > > 0, id 0, lun 0
> > > > > > --- end /var/log/messages ---
> > > > > >
> > > > > > If I place a disk in the drive, when I try to mount it the attempt fails
> > > > > > with the following being placed in /var/log/messages:
> > > > > >
> > > > > > --- begin /var/log/messages ---
> > > > > > Feb 26 19:46:58 localhost kernel: attempt to access beyond end of device
> > > > > > Feb 26 19:46:58 localhost kernel: sda: rw=0, want=66, limit=1
> > > > > > Feb 26 19:46:58 localhost kernel: isofs_fill_super: bread failed, dev=sda,
> > > > > > iso_blknum=16, block=32
> > > > > > --- end /var/log/messages ---
> > > > > >
> > > > > > Does somewhat have some idea how to get this drive working? Thanks.
> > > > > >
> > > > > > -Kipp
> > > > > >
> > > > > >
> > > > > >
> > > > > > -------------------------------------------------------
> > > > > > SF.Net is sponsored by: Speed Start Your Linux Apps Now.
> > > > > > Build and deploy apps & Web services for Linux with
> > > > > > a free DVD software kit from IBM. Click Now!
> > > > > > http://ads.osdn.com/?ad_id=1356&alloc_id=3438&op=click
> > > > > > _______________________________________________
> > > > > > [EMAIL PROTECTED]
> > > > > > To unsubscribe, use the last form field at:
> > > > > > https://lists.sourceforge.net/lists/listinfo/linux-usb-users
> > > > >
> > > > > --
> > > > > Matthew Dharm Home: [EMAIL PROTECTED]
> > > > > Maintainer, Linux USB Mass Storage Driver
> > > > >
> > > > > A: The most ironic oxymoron wins ...
> > > > > DP: "Microsoft Works"
> > > > > A: Uh, okay, you win.
> > > > > -- A.J. & Dust Puppy
> > > > > User Friendly, 1/18/1998
> > > > >
> > >
> > > --
> > > Matthew Dharm Home: [EMAIL PROTECTED]
> > > Maintainer, Linux USB Mass Storage Driver
> > >
> > > Okay, this isn't funny anymore! Let me down! I'll tell Bill on you!!
> > > -- Microsoft Salesman
> > > User Friendly, 4/1/1998
> > >
>
> --
> Matthew Dharm Home: [EMAIL PROTECTED]
> Maintainer, Linux USB Mass Storage Driver
>
> It's monday. It must be monday.
> -- Greg
> User Friendly, 5/4/1998
>
-------------------------------------------------------
This SF.Net email is sponsored by: IBM Linux Tutorials
Free Linux tutorial presented by Daniel Robbins, President and CEO of
GenToo technologies. Learn everything from fundamentals to system
administration.http://ads.osdn.com/?ad_id=1470&alloc_id=3638&op=click
_______________________________________________
[EMAIL PROTECTED]
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-users
