I didn't remove it, at least not on purpose. But I was in a hurry, don't know what I did wrong, sorry. Should I post it again with the correct CC?
Andre Am Montag, 15. M�rz 2004 17:25 schrieb Matthew Dharm: > Is there a reason you removed [EMAIL PROTECTED] from the > CC? The point is that I was trying to move the discussion to that list. > > Matt > > On Mon, Mar 15, 2004 at 11:27:38AM +0100, Andr? Welter wrote: > > Ok, here are the requested logs: > > > > first first for the not working 2.6.4: > > > > usb 3-2: new full speed USB device using address 3 > > usb-storage: USB Mass Storage device detected > > usb-storage: act_altsetting is 0, id_index is 91 > > usb-storage: -- associate_dev > > usb-storage: Transport: Bulk > > usb-storage: Protocol: Transparent SCSI > > usb-storage: Endpoints: In: 0xd8521f94 Out: 0xd8521f80 Int: 0xd8521fa8 > > (Period 32) > > usb-storage: usb_stor_control_msg: rq=fe rqtype=a1 value=0000 index=00 > > len=1 usb-storage: GetMaxLUN command result is -32, data is 0 > > usb-storage: *** thread sleeping. > > scsi0 : SCSI emulation for USB Mass Storage devices > > usb-storage: queuecommand called > > usb-storage: *** thread awakened. > > usb-storage: Command INQUIRY (6 bytes) > > usb-storage: 12 00 00 00 24 00 > > usb-storage: Bulk Command S 0x43425355 T 0x1 L 36 F 128 Trg 0 LUN 0 CL 6 > > usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes > > usb-storage: Status code -32; transferred 31/31 > > usb-storage: clearing endpoint halt for pipe 0xc0008300 > > usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=01 > > len=0 usb-storage: usb_stor_clear_halt: result = 0 > > usb-storage: Bulk command transfer result=2 > > usb-storage: -- transport indicates error, resetting > > usb-storage: usb_stor_Bulk_reset called > > usb-storage: usb_stor_control_msg: rq=ff rqtype=21 value=0000 index=00 > > len=0 usb-storage: command_abort called > > usb-storage: usb_stor_stop_transport called > > usb-storage: -- cancelling URB > > usb-storage: Soft reset failed: -104 > > usb-storage: scsi cmd done, result=0x70000 > > usb-storage: *** thread sleeping. > > usb-storage: queuecommand called > > usb-storage: *** thread awakened. > > usb-storage: Command TEST_UNIT_READY (6 bytes) > > usb-storage: 00 00 00 00 00 00 > > usb-storage: Bulk Command S 0x43425355 T 0x1 L 0 F 0 Trg 0 LUN 0 CL 6 > > usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes > > usb-storage: Status code 0; transferred 31/31 > > usb-storage: -- transfer complete > > usb-storage: Bulk command transfer result=0 > > usb-storage: Attempting to get CSW... > > usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes > > usb-storage: command_abort called > > usb-storage: usb_stor_stop_transport called > > usb-storage: -- cancelling URB > > usb-storage: Status code -104; transferred 0/13 > > usb-storage: -- transfer cancelled > > usb-storage: Bulk status result = 4 > > usb-storage: -- command was aborted > > usb-storage: usb_stor_Bulk_reset called > > usb-storage: usb_stor_control_msg: rq=ff rqtype=21 value=0000 index=00 > > len=0 usb-storage: Soft reset: clearing bulk-in endpoint halt > > usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=82 > > len=0 usb-storage: usb_stor_clear_halt: result = 0 > > usb-storage: Soft reset: clearing bulk-out endpoint halt > > usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=01 > > len=0 usb-storage: usb_stor_clear_halt: result = 0 > > usb-storage: Soft reset done > > usb-storage: scsi command aborted > > usb-storage: *** thread sleeping. > > usb-storage: device_reset called > > usb-storage: usb_stor_Bulk_reset called > > usb-storage: usb_stor_control_msg: rq=ff rqtype=21 value=0000 index=00 > > len=0 usb-storage: Timeout -- cancelling URB > > usb-storage: Soft reset failed: -104 > > usb-storage: bus_reset called > > > > > > > > now for the working 2.4.25: > > > > hub.c: new USB device 00:10.1-2, assigned address 3 > > usb.c: kmalloc IF cfd8e140, numif 1 > > usb.c: new device strings: Mfr=1, Product=2, SerialNumber=5 > > usb.c: USB device number 3 default language ID 0x409 > > Manufacturer: Iomega > > Product: USB Zip 100 > > SerialNumber: 0000000000F44DEC > > usb.c: unhandled interfaces on device > > usb.c: USB device 3 (vend/prod 0x59b/0x1) is not claimed by any active > > driver. Length = 18 > > DescriptorType = 01 > > USB version = 1.00 > > Vendor:Product = 059b:0001 > > MaxPacketSize0 = 64 > > NumConfigurations = 1 > > Device version = 1.00 > > Device Class:SubClass:Protocol = 00:00:00 > > Per-interface classes > > Configuration: > > bLength = 9 > > bDescriptorType = 02 > > wTotalLength = 0027 > > bNumInterfaces = 01 > > bConfigurationValue = 01 > > iConfiguration = 03 > > bmAttributes = 40 > > MaxPower = 0mA > > > > Interface: 0 > > Alternate Setting: 0 > > bLength = 9 > > bDescriptorType = 04 > > bInterfaceNumber = 00 > > bAlternateSetting = 00 > > bNumEndpoints = 03 > > bInterface Class:SubClass:Protocol = 08:06:50 > > iInterface = 04 > > Endpoint: > > bLength = 7 > > bDescriptorType = 05 > > bEndpointAddress = 01 (out) > > bmAttributes = 02 (Bulk) > > wMaxPacketSize = 0040 > > bInterval = 00 > > Endpoint: > > bLength = 7 > > bDescriptorType = 05 > > bEndpointAddress = 82 (in) > > bmAttributes = 02 (Bulk) > > wMaxPacketSize = 0040 > > bInterval = 00 > > Endpoint: > > bLength = 7 > > bDescriptorType = 05 > > bEndpointAddress = 83 (in) > > bmAttributes = 03 (Interrupt) > > wMaxPacketSize = 0002 > > bInterval = 20 > > usb.c: kusbd: /sbin/hotplug add 3 > > hub.c: port 1, portstatus 103, change 0, 12 Mb/s > > hub.c: port 2, portstatus 103, change 0, 12 Mb/s > > Initializing USB Mass Storage driver... > > usb.c: registered new driver usb-storage > > usb-storage: act_altsettting is 0 > > usb-storage: id_index calculated to be: 89 > > usb-storage: Array length appears to be: 91 > > usb-storage: USB Mass Storage device detected > > usb-storage: Endpoints: In: 0xcf8b1b94 Out: 0xcf8b1b80 Int: 0xcf8b1ba8 > > (Period 32) > > usb-storage: New GUID 059b00010000000000f44dec > > usb-uhci.c: interrupt, status 2, frame# 1620 > > usb-storage: GetMaxLUN command result is 0, data is 128 > > usb-storage: Transport: Bulk > > usb-storage: Protocol: Transparent SCSI > > usb-storage: *** thread sleeping. > > scsi1 : SCSI emulation for USB Mass Storage devices > > usb-storage: queuecommand() called > > usb-storage: *** thread awakened. > > usb-storage: Command INQUIRY (6 bytes) > > usb-storage: 12 00 00 00 ff 00 ab d5 21 ac 1e c0 > > usb-storage: Bulk command S 0x43425355 T 0x1 Trg 0 LUN 0 L 255 F 128 CL 6 > > usb-storage: Bulk command transfer result=0 > > usb-storage: usb_stor_transfer_partial(): xfer 255 bytes > > usb-storage: usb_stor_bulk_msg() returned 0 xferred 122/255 > > usb-storage: Bulk data transfer result 0x1 > > usb-storage: Attempting to get CSW... > > usb-storage: clearing endpoint halt for pipe 0xc0010380 > > usb-storage: usb_stor_clear_halt: result=0 > > usb-storage: Attempting to get CSW (2nd try)... > > usb-storage: Bulk status result = 0 > > usb-storage: Bulk status Sig 0x53425355 T 0x1 R 133 Stat 0x0 > > usb-storage: Fixing INQUIRY data to show SCSI rev 2 - was 0 > > usb-storage: scsi cmd done, result=0x0 > > usb-storage: *** thread sleeping. > > Vendor: IOMEGA Model: ZIP 100 Rev: 02.U > > Type: Direct-Access ANSI SCSI revision: 02 > > usb-storage: queuecommand() called > > usb-storage: *** thread awakened. > > usb-storage: Bad target number (1/0) > > usb-storage: *** thread sleeping. > > usb-storage: queuecommand() called > > usb-storage: *** thread awakened. > > usb-storage: Bad target number (2/0) > > usb-storage: *** thread sleeping. > > usb-storage: queuecommand() called > > usb-storage: *** thread awakened. > > usb-storage: Bad target number (3/0) > > usb-storage: *** thread sleeping. > > usb-storage: queuecommand() called > > usb-storage: *** thread awakened. > > usb-storage: Bad target number (4/0) > > usb-storage: *** thread sleeping. > > usb-storage: queuecommand() called > > usb-storage: *** thread awakened. > > usb-storage: Bad target number (5/0) > > usb-storage: *** thread sleeping. > > usb-storage: queuecommand() called > > usb-storage: *** thread awakened. > > usb-storage: Bad target number (6/0) > > usb-storage: *** thread sleeping. > > usb-storage: queuecommand() called > > usb-storage: *** thread awakened. > > usb-storage: Bad target number (7/0) > > usb-storage: *** thread sleeping. > > Attached scsi removable disk sdb at scsi1, channel 0, id 0, lun 0 > > usb-storage: queuecommand() called > > usb-storage: *** thread awakened. > > usb-storage: Command TEST_UNIT_READY (6 bytes) > > usb-storage: 00 00 00 00 00 00 00 00 00 00 00 00 > > usb-storage: Bulk command S 0x43425355 T 0x2 Trg 0 LUN 0 L 0 F 0 CL 6 > > usb-storage: Bulk command transfer result=0 > > usb-storage: Attempting to get CSW... > > usb-storage: Bulk status result = 0 > > usb-storage: Bulk status Sig 0x53425355 T 0x2 R 0 Stat 0x1 > > usb-storage: -- transport indicates command failure > > usb-storage: Issuing auto-REQUEST_SENSE > > usb-storage: Bulk command S 0x43425355 T 0x3 Trg 0 LUN 0 L 18 F 128 CL 6 > > usb-storage: Bulk command transfer result=0 > > usb-storage: usb_stor_transfer_partial(): xfer 18 bytes > > usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18 > > usb-storage: usb_stor_transfer_partial(): transfer complete > > usb-storage: Bulk data transfer result 0x0 > > usb-storage: Attempting to get CSW... > > usb-storage: Bulk status result = 0 > > usb-storage: Bulk status Sig 0x53425355 T 0x3 R 0 Stat 0x0 > > usb-storage: -- Result from auto-sense is 0 > > usb-storage: -- code: 0x70, key: 0x6, ASC: 0x29, ASCQ: 0x0 > > usb-storage: Unit Attention: device reset occurred > > usb-storage: scsi cmd done, result=0x2 > > usb-storage: *** thread sleeping. > > usb-storage: queuecommand() called > > usb-storage: *** thread awakened. > > usb-storage: Command TEST_UNIT_READY (6 bytes) > > usb-storage: 00 00 00 00 00 00 00 00 00 00 00 00 > > usb-storage: Bulk command S 0x43425355 T 0x4 Trg 0 LUN 0 L 0 F 0 CL 6 > > usb-storage: Bulk command transfer result=0 > > usb-storage: Attempting to get CSW... > > usb-storage: Bulk status result = 0 > > usb-storage: Bulk status Sig 0x53425355 T 0x4 R 0 Stat 0x1 > > usb-storage: -- transport indicates command failure > > usb-storage: Issuing auto-REQUEST_SENSE > > usb-storage: Bulk command S 0x43425355 T 0x5 Trg 0 LUN 0 L 18 F 128 CL 6 > > usb-storage: Bulk command transfer result=0 > > usb-storage: usb_stor_transfer_partial(): xfer 18 bytes > > usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18 > > usb-storage: usb_stor_transfer_partial(): transfer complete > > usb-storage: Bulk data transfer result 0x0 > > usb-storage: Attempting to get CSW... > > usb-storage: Bulk status result = 0 > > usb-storage: Bulk status Sig 0x53425355 T 0x5 R 0 Stat 0x0 > > usb-storage: -- Result from auto-sense is 0 > > usb-storage: -- code: 0x70, key: 0x6, ASC: 0x28, ASCQ: 0x0 > > usb-storage: Unit Attention: not ready to ready transition > > usb-storage: scsi cmd done, result=0x2 > > usb-storage: *** thread sleeping. > > usb-storage: queuecommand() called > > usb-storage: *** thread awakened. > > usb-storage: Command TEST_UNIT_READY (6 bytes) > > usb-storage: 00 00 00 00 00 00 00 00 00 00 00 00 > > usb-storage: Bulk command S 0x43425355 T 0x6 Trg 0 LUN 0 L 0 F 0 CL 6 > > usb-storage: Bulk command transfer result=0 > > usb-storage: Attempting to get CSW... > > usb-storage: Bulk status result = 0 > > usb-storage: Bulk status Sig 0x53425355 T 0x6 R 0 Stat 0x0 > > usb-storage: scsi cmd done, result=0x0 > > usb-storage: *** thread sleeping. > > usb-storage: queuecommand() called > > usb-storage: *** thread awakened. > > usb-storage: Command READ_CAPACITY (10 bytes) > > usb-storage: 25 00 00 00 00 00 00 00 00 00 00 00 > > usb-storage: Bulk command S 0x43425355 T 0x7 Trg 0 LUN 0 L 8 F 128 CL 10 > > usb-storage: Bulk command transfer result=0 > > usb-storage: usb_stor_transfer_partial(): xfer 8 bytes > > usb-storage: usb_stor_bulk_msg() returned 0 xferred 8/8 > > usb-storage: usb_stor_transfer_partial(): transfer complete > > usb-storage: Bulk data transfer result 0x0 > > usb-storage: Attempting to get CSW... > > usb-storage: Bulk status result = 0 > > usb-storage: Bulk status Sig 0x53425355 T 0x7 R 0 Stat 0x0 > > usb-storage: scsi cmd done, result=0x0 > > usb-storage: *** thread sleeping. > > SCSI device sdb: 196608 512-byte hdwr sectors (101 MB) > > usb-storage: queuecommand() called > > usb-storage: *** thread awakened. > > usb-storage: Command MODE_SENSE (6 bytes) > > usb-storage: 1a 00 3f 00 ff 00 00 00 00 00 00 00 > > usb-storage: Bulk command S 0x43425355 T 0x8 Trg 0 LUN 0 L 255 F 128 CL 6 > > usb-storage: Bulk command transfer result=0 > > usb-storage: usb_stor_transfer_partial(): xfer 255 bytes > > usb-storage: usb_stor_bulk_msg() returned 0 xferred 58/255 > > usb-storage: Bulk data transfer result 0x1 > > usb-storage: Attempting to get CSW... > > usb-storage: clearing endpoint halt for pipe 0xc0010380 > > usb-storage: usb_stor_clear_halt: result=0 > > usb-storage: Attempting to get CSW (2nd try)... > > usb-storage: Bulk status result = 0 > > usb-storage: Bulk status Sig 0x53425355 T 0x8 R 197 Stat 0x0 > > usb-storage: scsi cmd done, result=0x0 > > usb-storage: *** thread sleeping. > > sdb: Write Protect is off > > sdb:<7>usb-storage: queuecommand() called > > usb-storage: *** thread awakened. > > usb-storage: Command READ_10 (10 bytes) > > usb-storage: 28 00 00 00 00 00 00 00 08 00 00 00 > > usb-storage: Bulk command S 0x43425355 T 0x9 Trg 0 LUN 0 L 4096 F 128 CL > > 10 usb-storage: Bulk command transfer result=0 > > usb-storage: usb_stor_transfer_partial(): xfer 4096 bytes > > usb-storage: usb_stor_bulk_msg() returned 0 xferred 4096/4096 > > usb-storage: usb_stor_transfer_partial(): transfer complete > > usb-storage: Bulk data transfer result 0x0 > > usb-storage: Attempting to get CSW... > > usb-storage: Bulk status result = 0 > > usb-storage: Bulk status Sig 0x53425355 T 0x9 R 0 Stat 0x0 > > usb-storage: scsi cmd done, result=0x0 > > usb-storage: *** thread sleeping. > > sdb4 > > WARNING: USB Mass Storage data integrity not assured > > USB Mass Storage device found at 3 > > usb.c: usb-storage driver claimed interface cfd8e140 > > USB Mass Storage support registered. > > > > Hope they're helpful. > > > > Andre > > > > Am Montag, 15. M�rz 2004 05:03 schrieb Matthew Dharm: > > > I see similar results. Tho, sometimes it does work (the error & reset > > > recovery eventuall get us back to a working state). > > > > > > This is an interesting failure, because I don't think we're really > > > doing anything different here than under 2.4.x -- it's just an INQUIRY > > > command. > > > > > > One problem (it looks like) is that usb_device_reset() isn't returning > > > when we request that the device get reset. That's pretty messed up, in > > > and of itself. > > > > > > Doing a quick test, my Zip250 (self-powered) works just fine. So does > > > my Zip750. > > > > > > Doing some tests with my Zip100, I can see that the system gets into a > > > state where I can send a CBW, but not get a CSW. It almost looks like > > > the data toggles are screwed up or something, but those sorts of HCD > > > bugs were purged a long time ago. > > > > > > As Ged points out, I am pretty busy. So if you could generate a log > > > similar to what you gave, but for a working 2.4 kernel, that would be > > > helpful. Actually, send both as I'm also CC'ing the usb-storage > > > development list on this. > > > > > > Matt > > > > > > On Sun, Mar 14, 2004 at 11:59:34AM +0000, Ged Haywood wrote: > > > > Hi there, > > > > > > > > According to > > > > > > > > http://www2.one-eyed-alien.net/~mdharm/linux-usb/ > > > > > > > > your drive is one of those that M. Dharm has available to him, so I > > > > guess he'll be looking at it. You might have to be patient, this USB > > > > stuff keeps him pretty busy when he's not otherwise occupied. :) > > > > > > > > On Fri, 12 Mar 2004, [iso-8859-15] Andr� Welter wrote: > > > > > I'm trying to get my USB Zip100 working with kernel 2.6. It works > > > > > just fine under 2.4. > > > > > > > > 73, > > > > Ged. > > > > ------------------------------------------------------- > > This SF.Net email is sponsored by: IBM Linux Tutorials > > Free Linux tutorial presented by Daniel Robbins, President and CEO of > > GenToo technologies. Learn everything from fundamentals to system > > administration.http://ads.osdn.com/?ad_id70&alloc_id638&op�k > > _______________________________________________ > > [EMAIL PROTECTED] > > To unsubscribe, use the last form field at: > > https://lists.sourceforge.net/lists/listinfo/linux-usb-users ------------------------------------------------------- This SF.Net email is sponsored by: IBM Linux Tutorials Free Linux tutorial presented by Daniel Robbins, President and CEO of GenToo technologies. Learn everything from fundamentals to system administration.http://ads.osdn.com/?ad_id70&alloc_id638&op=click _______________________________________________ [EMAIL PROTECTED] To unsubscribe, use the last form field at: https://lists.sourceforge.net/lists/listinfo/linux-usb-users
