hallo to everyone, I've a pen drive that I can't mount with kernel 2.6.5. same drive is ok with 2.4
My drive is so defined by lsusb: #lsusb Bus 004 Device 002: ID 08ec:0834 M-Systems Flash Disk Pioneers I use these modules: - uhci-hcd (VIA chipset) - usbcore - hid - usb-storage - sd_mod - scsi_mod After connect I can't remove usb-storage module; I've noticed that in kernel 2.4 I could see in /var/log/messages this line: - Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0 - Nothing of this I've seen with 2.6 kernel...... This is dmesg after connecting pen drive (usb-storage verbose debug): #dmesg usb 4-1: new full speed USB device using address 2 SCSI subsystem initialized Initializing USB Mass Storage driver... usb-storage: USB Mass Storage device detected usb-storage: altsetting is 0, id_index is 119 usb-storage: -- associate_dev usb-storage: Transport: Bulk usb-storage: Protocol: Transparent SCSI usb-storage: Endpoints: In: 0xc47114c0 Out: 0xc47114d4 Int: 0x00000000 (Period 0) usb-storage: usb_stor_control_msg: rq=fe rqtype=a1 value=0000 index=00 len=1 usb-storage: GetMaxLUN command result is 1, data is 0 usb-storage: *** thread sleeping. scsi0 : SCSI emulation for USB Mass Storage devices usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Command INQUIRY (6 bytes) usb-storage: 12 00 00 00 24 00 usb-storage: Bulk Command S 0x43425355 T 0x1 L 36 F 128 Trg 0 LUN 0 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: usb_stor_bulk_transfer_buf: xfer 36 bytes usb-storage: Status code 0; transferred 36/36 usb-storage: -- transfer complete usb-storage: Bulk data transfer result 0x0 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code 0; transferred 13/13 usb-storage: -- transfer complete usb-storage: Bulk status result = 0 usb-storage: Bulk Status S 0x53425355 T 0x1 R 0 Stat 0x0 usb-storage: scsi cmd done, result=0x0 usb-storage: *** thread sleeping. Vendor: Generic Model: Rev: Type: Direct-Access ANSI SCSI revision: 02 usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Command TEST_UNIT_READY (6 bytes) usb-storage: 00 00 00 00 00 00 usb-storage: Bulk Command S 0x43425355 T 0x2 L 0 F 0 Trg 0 LUN 0 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code 0; transferred 13/13 usb-storage: -- transfer complete usb-storage: Bulk status result = 0 usb-storage: Bulk Status S 0x53425355 T 0x2 R 0 Stat 0x0 usb-storage: scsi cmd done, result=0x0 usb-storage: *** thread sleeping. usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Command READ_CAPACITY (10 bytes) usb-storage: 25 00 00 00 00 00 00 00 00 00 usb-storage: Bulk Command S 0x43425355 T 0x3 L 8 F 128 Trg 0 LUN 0 CL 10 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: usb_stor_bulk_transfer_buf: xfer 8 bytes usb-storage: Status code 0; transferred 8/8 usb-storage: -- transfer complete usb-storage: Bulk data transfer result 0x0 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code 0; transferred 13/13 usb-storage: -- transfer complete usb-storage: Bulk status result = 0 usb-storage: Bulk Status S 0x53425355 T 0x3 R 0 Stat 0x0 usb-storage: scsi cmd done, result=0x0 usb-storage: *** thread sleeping. SCSI device sda: 503808 512-byte hdwr sectors (258 MB) usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Command MODE_SENSE (6 bytes) usb-storage: 1a 00 3f 00 04 00 usb-storage: Bulk Command S 0x43425355 T 0x4 L 4 F 128 Trg 0 LUN 0 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: usb_stor_bulk_transfer_buf: xfer 4 bytes usb-storage: Status code 0; transferred 4/4 usb-storage: -- transfer complete usb-storage: Bulk data transfer result 0x0 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code 0; transferred 13/13 usb-storage: -- transfer complete usb-storage: Bulk status result = 0 usb-storage: Bulk Status S 0x53425355 T 0x4 R 0 Stat 0x0 usb-storage: scsi cmd done, result=0x0 usb-storage: *** thread sleeping. sda: Write Protect is off sda: Mode Sense: 03 00 00 00 usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Command MODE_SENSE (6 bytes) usb-storage: 1a 00 08 00 04 00 usb-storage: Bulk Command S 0x43425355 T 0x5 L 4 F 128 Trg 0 LUN 0 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: usb_stor_bulk_transfer_buf: xfer 4 bytes bttv0: skipped frame. no signal? high irq latency? [main=1bbec000,o_vbi=1bbec018,o_field=18b17000,rc=18b1701c] usb-storage: command_abort called usb-storage: usb_stor_stop_transport called usb-storage: -- cancelling URB usb-storage: Status code -104; transferred 0/4 usb-storage: -- transfer cancelled usb-storage: Bulk data transfer result 0x4 usb-storage: -- command was aborted usb-storage: usb_stor_Bulk_reset called usb-storage: usb_stor_control_msg: rq=ff rqtype=21 value=0000 index=00 len=0 usb-storage: Soft reset failed: -32 usb-storage: scsi command aborted usb-storage: queuecommand called usb-storage: *** thread sleeping. usb-storage: *** thread awakened. usb-storage: Command TEST_UNIT_READY (6 bytes) usb-storage: 00 00 00 00 00 00 usb-storage: Bulk Command S 0x43425355 T 0x5 L 0 F 0 Trg 0 LUN 0 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes Thanx to all scido ------------------------------------------------------- This SF.Net email is sponsored by: SourceForge.net Broadband Sign-up now for SourceForge Broadband and get the fastest 6.0/768 connection for only $19.95/mo for the first 3 months! http://ads.osdn.com/?ad_id=2562&alloc_id=6184&op=click _______________________________________________ [EMAIL PROTECTED] To unsubscribe, use the last form field at: https://lists.sourceforge.net/lists/listinfo/linux-usb-users
