Hi everyone, I attached a 80-GB-HDD to my server using USB-2. The server runs Debian 3.1 with Kernel 2.8.6.
When I try to copy a very large file (about 4 GB) from the USD-HDD to another pc there is always an error: > SCSI error : <0 0 0 0> return code = 0x70000 > end_request: I/O error, dev sda, sector 28779959 > usb-storage: queuecommand called > usb-storage: *** thread awakened. > usb-storage: Command READ_10 (10 bytes) > usb-storage: 28 00 01 b7 25 bf 00 00 50 00 > usb-storage: Bulk Command S 0x43425355 T 0x40331 L 40960 F 128 Trg 0 LUN 0 CL 10 > usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes > ehci_hcd 0000:00:09.3: devpath 5 ep2out 3strikes > usb-storage: Status code -71; transferred 0/31 > usb-storage: -- unknown error > usb-storage: Bulk command transfer result=4 > usb-storage: -- transport indicates error, resetting > usb-storage: usb_stor_Bulk_reset called > usb-storage: usb_stor_control_msg: rq=ff rqtype=21 value=0000 index=00 len=0 > ehci_hcd 0000:00:09.3: GetStatus port 5 status 001002 POWER sig=se0 CSC After that the device hangs and I have to reboot to unmount. /proc/bus/usb/devices shows this: > T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 6 > B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0 > D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS= 8 #Cfgs= 1 > P: Vendor=0000 ProdID=0000 Rev= 2.06 > S: Manufacturer=Linux 2.6.8 ehci_hcd > S: Product=ALi Corporation USB 2.0 Controller > S: SerialNumber=0000:00:09.3 > C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA > I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub > E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=256ms > > T: Bus=01 Lev=01 Prnt=01 Port=04 Cnt=01 Dev#= 3 Spd=480 MxCh= 0 > D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 > P: Vendor=05e3 ProdID=0702 Rev= 0.02 > S: Product=USB TO IDE > C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 96mA > I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage > E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms > E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=125us This is the internal controller-card which I use to connect the hdd: > 0000:00:09.3 USB Controller: ALi Corporation USB 2.0 Controller (rev 01) (prog-if 20 > [EHCI]) > Subsystem: ALi Corporation USB 2.0 Controller > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- > <MAbort- >SERR- <PERR- > Latency: 64 (20000ns max), Cache Line Size: 0x08 (32 bytes) > Interrupt: pin A routed to IRQ 9 > Region 0: Memory at e3000000 (32-bit, non-prefetchable) [size=256] > Capabilities: [50] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA > PME(D0+,D1-,D2-,D3hot+,D3cold+) > Status: D0 PME-Enable- DSel=0 DScale=0 PME+ > Capabilities: [58] #0a [2090] Is there anything I can do about this? Mit freundlichen Gr�ssen, Heiko Rittelmeier -- www.computerbetrug.de Gegen Straftaten im Internet www.dialerhilfe.de Gegen unseri�se Dialernutzung ------------------------------------------------------- This SF.Net email is sponsored by: YOU BE THE JUDGE. Be one of 170 Project Admins to receive an Apple iPod Mini FREE for your judgement on who ports your project to Linux PPC the best. Sponsored by IBM. Deadline: Sept. 24. Go here: http://sf.net/ppc_contest.php _______________________________________________ [EMAIL PROTECTED] To unsubscribe, use the last form field at: https://lists.sourceforge.net/lists/listinfo/linux-usb-users
