No matter what device I try to plug in to this old machine the 2.6 kernels
won't work. The 2.4 works fine. The /proc/interrupt count is increasing
correctly.
Here's the pci info and log with debug from 2.6.11. If you want to see
logs with debug from 2.4.26 that show when it does work, I can provide
that too.
00:0e.2 USB Controller: Compaq Computer Corporation ZFMicro Chipset USB
(rev 11) (prog-if 10 [OHCI])
Subsystem: Compaq Computer Corporation ZFMicro Chipset USB
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR-
Latency: 64, cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 44080000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [e0] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Mar 5 07:47:17 nightshade kernel: usbcore: registered new driver usbfs
Mar 5 07:47:17 nightshade kernel: usbcore: registered new driver hub
Mar 5 07:47:17 nightshade kernel: ohci_hcd: 2004 Nov 08 USB 1.1 'Open'
Host Controller (OHCI) Driver (PCI)
Mar 5 07:47:17 nightshade kernel: ohci_hcd: block sizes: ed 64 td 64
Mar 5 07:47:17 nightshade kernel: ACPI: PCI interrupt 0000:00:0e.2[A] ->
GSI 11 (level, low) -> IRQ 11
Mar 5 07:47:17 nightshade kernel: ohci_hcd 0000:00:0e.2: Compaq Computer
Corporation ZFMicro Chipset USB
Mar 5 07:47:17 nightshade kernel: ohci_hcd 0000:00:0e.2: USB HC TakeOver
from BIOS/SMM
Mar 5 07:47:17 nightshade kernel: ohci_hcd 0000:00:0e.2: irq 11, pci mem
0x44080000
Mar 5 07:47:17 nightshade kernel: ohci_hcd 0000:00:0e.2: new USB bus
registered, assigned bus number 1
Mar 5 07:47:17 nightshade kernel: ohci_hcd 0000:00:0e.2: resetting from
state 'reset', control = 0x0
Mar 5 07:47:17 nightshade kernel: ohci_hcd 0000:00:0e.2: enabling
initreset quirk
Mar 5 07:47:17 nightshade kernel: ohci_hcd 0000:00:0e.2: OHCI controller
state
Mar 5 07:47:17 nightshade kernel: ohci_hcd 0000:00:0e.2: OHCI 1.0, with
legacy support registers
Mar 5 07:47:17 nightshade kernel: ohci_hcd 0000:00:0e.2: control 0x083
HCFS=operational CBSR=3
Mar 5 07:47:17 nightshade kernel: ohci_hcd 0000:00:0e.2: cmdstatus
0x00000 SOC=0
Mar 5 07:47:17 nightshade kernel: ohci_hcd 0000:00:0e.2: intrstatus
0x00000004 SF
Mar 5 07:47:17 nightshade kernel: ohci_hcd 0000:00:0e.2: intrenable
0xc000001a MIE OC UE RD WDH
Mar 5 07:47:17 nightshade kernel: ohci_hcd 0000:00:0e.2: hcca frame #0003
Mar 5 07:47:17 nightshade kernel: ohci_hcd 0000:00:0e.2: roothub.a
01000202 POTPGT=1 NPS NDP=2
Mar 5 07:47:17 nightshade kernel: ohci_hcd 0000:00:0e.2: roothub.b
00000000 PPCM=0000 DR=0000
Mar 5 07:47:17 nightshade kernel: ohci_hcd 0000:00:0e.2: roothub.status
00008000 DRWE
Mar 5 07:47:17 nightshade kernel: ohci_hcd 0000:00:0e.2:
roothub.portstatus [0] 0x00000100 PPS
Mar 5 07:47:17 nightshade kernel: ohci_hcd 0000:00:0e.2:
roothub.portstatus [1] 0x00000100 PPS
Mar 5 07:47:17 nightshade kernel: usb usb1: new device strings: Mfr=3,
Product=2, SerialNumber=1
Mar 5 07:47:17 nightshade kernel: usb usb1: default language 0x0409
Mar 5 07:47:17 nightshade kernel: usb usb1: Product: Compaq Computer
Corporation ZFMicro Chipset USB
Mar 5 07:47:17 nightshade kernel: usb usb1: Manufacturer: Linux 2.6.11
ohci_hcd
Mar 5 07:47:17 nightshade kernel: usb usb1: SerialNumber: 0000:00:0e.2
Mar 5 07:47:17 nightshade kernel: usb usb1: hotplug
Mar 5 07:47:17 nightshade kernel: usb usb1: adding 1-0:1.0 (config #1,
interface 0)
Mar 5 07:47:17 nightshade kernel: usb 1-0:1.0: hotplug
Mar 5 07:47:17 nightshade kernel: hub 1-0:1.0: usb_probe_interface
Mar 5 07:47:17 nightshade kernel: hub 1-0:1.0: usb_probe_interface - got id
Mar 5 07:47:17 nightshade kernel: hub 1-0:1.0: USB hub found
Mar 5 07:47:17 nightshade kernel: hub 1-0:1.0: 2 ports detected
Mar 5 07:47:17 nightshade kernel: hub 1-0:1.0: standalone hub
Mar 5 07:47:17 nightshade kernel: hub 1-0:1.0: no power switching (usb 1.0)
Mar 5 07:47:17 nightshade kernel: hub 1-0:1.0: global over-current
protection
Mar 5 07:47:17 nightshade kernel: hub 1-0:1.0: power on to power good
time: 2ms
Mar 5 07:47:17 nightshade kernel: hub 1-0:1.0: local power source is good
Mar 5 07:47:17 nightshade kernel: hub 1-0:1.0: no over-current condition
exists
Mar 5 07:47:17 nightshade kernel: ohci_hcd 0000:00:0e.2: created debug files
*** From here:
Mar 5 07:47:17 nightshade kernel: hub 1-0:1.0: state 5 ports 2 chg 0006
evt 0007
Mar 5 07:47:17 nightshade kernel: ohci_hcd 0000:00:0e.2: GetStatus
roothub.portstatus [0] = 0x00000100 PPS
Mar 5 07:47:17 nightshade kernel: hub 1-0:1.0: port 1, status 0100,
change 0000, 12 Mb/s
Mar 5 07:47:17 nightshade kernel: ohci_hcd 0000:00:0e.2: GetStatus
roothub.portstatus [1] = 0x00000100 PPS
Mar 5 07:47:17 nightshade kernel: hub 1-0:1.0: port 2, status 0100,
change 0000, 12 Mb/s
Mar 5 07:47:24 nightshade logger: /etc/rc.d/rc.hotplug start (entering
script)
Mar 5 07:47:24 nightshade input.agent[2407]: ... no modules for INPUT
product 0011/0001/0001/ab41
Mar 5 07:47:24 nightshade input.agent[2414]: ... no modules for INPUT
product 0011/0002/0001/0000
Mar 5 07:47:30 nightshade logger: /etc/rc.d/rc.hotplug start (exiting
script)
Mar 5 07:48:12 nightshade kernel: hub 1-0:1.0: state 5 ports 2 chg 0000
evt 0002
Mar 5 07:48:12 nightshade kernel: ohci_hcd 0000:00:0e.2: GetStatus
roothub.portstatus [0] = 0x00010101 CSC PPS CCS
Mar 5 07:48:12 nightshade kernel: hub 1-0:1.0: port 1, status 0101,
change 0001, 12 Mb/s
Mar 5 07:48:12 nightshade kernel: ohci_hcd 0000:00:0e.2: GetStatus
roothub.portstatus [0] = 0x00000101 PPS CCS
Mar 5 07:48:12 nightshade last message repeated 4 times
Mar 5 07:48:12 nightshade kernel: hub 1-0:1.0: debounce: port 1: total
100ms stable 100ms status 0x101
Mar 5 07:48:12 nightshade kernel: ohci_hcd 0000:00:0e.2: GetStatus
roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS
Mar 5 07:48:12 nightshade kernel: usb 1-1: new full speed USB device
using ohci_hcd and address 2
Mar 5 07:48:12 nightshade kernel: drivers/usb/host/ohci-dbg.c: SUB
c51a9bc0 dev=0 ep=0in-ctrl flags=10 len=0/64 stat=-115
Mar 5 07:48:12 nightshade kernel: drivers/usb/host/ohci-dbg.c: RET
c51a9bc0 dev=0 ep=0in-ctrl flags=10 len=18/64 stat=0
Mar 5 07:48:12 nightshade kernel: drivers/usb/host/ohci-dbg.c: setup(8):
80 06 00 01 00 00 40 00
Mar 5 07:48:12 nightshade kernel: drivers/usb/host/ohci-dbg.c:
data(18/64): 12 01 00 02 00 00 00 40 7d 0d 00 16 10 01 01 02... stat:0
Mar 5 07:48:12 nightshade kernel: drivers/usb/host/ohci-dbg.c: SUB
c51a9bc0 dev=0 ep=0in-ctrl flags=10 len=0/64 stat=-115
Mar 5 07:48:12 nightshade kernel: drivers/usb/host/ohci-dbg.c: RET
c51a9bc0 dev=0 ep=0in-ctrl flags=10 len=18/64 stat=0
Mar 5 07:48:12 nightshade kernel: drivers/usb/host/ohci-dbg.c: setup(8):
80 06 00 01 00 00 40 00
Mar 5 07:48:12 nightshade kernel: drivers/usb/host/ohci-dbg.c:
data(18/64): 12 01 00 02 00 00 00 40 7d 0d 00 16 10 01 01 02... stat:0
Mar 5 07:48:12 nightshade kernel: spurious 8259A interrupt: IRQ7.
Mar 5 07:48:12 nightshade kernel: drivers/usb/host/ohci-dbg.c: SUB
c51a9bc0 dev=0 ep=0in-ctrl flags=10 len=0/64 stat=-115
Mar 5 07:48:13 nightshade kernel: drivers/usb/host/ohci-dbg.c: UNLINK
c51a9bc0 dev=0 ep=0in-ctrl flags=10 len=0/64 stat=-104
Mar 5 07:48:13 nightshade kernel: drivers/usb/host/ohci-dbg.c: RET
c51a9bc0 dev=0 ep=0in-ctrl flags=10 len=0/64 stat=-104
Mar 5 07:48:13 nightshade kernel: drivers/usb/host/ohci-dbg.c: setup(8):
80 06 00 01 00 00 40 00
Mar 5 07:48:13 nightshade kernel: drivers/usb/host/ohci-dbg.c:
data(0/64): stat:-104
Mar 5 07:48:13 nightshade kernel: ohci_hcd 0000:00:0e.2: GetStatus
roothub.portstatus [0] = 0x00110103 PRSC CSC PPS PES CCS
Mar 5 07:48:13 nightshade kernel: hub 1-0:1.0: port 1 not enabled, trying
reset again...
Mar 5 07:48:13 nightshade kernel: ohci_hcd 0000:00:0e.2: GetStatus
roothub.portstatus [0] = 0x00110103 PRSC CSC PPS PES CCS
Mar 5 07:48:13 nightshade kernel: hub 1-0:1.0: port 1 not enabled, trying
reset again...
Mar 5 07:48:13 nightshade kernel: ohci_hcd 0000:00:0e.2: GetStatus
roothub.portstatus [0] = 0x00110103 PRSC CSC PPS PES CCS
Mar 5 07:48:13 nightshade kernel: hub 1-0:1.0: port 1 not enabled, trying
reset again...
Mar 5 07:48:14 nightshade kernel: ohci_hcd 0000:00:0e.2: GetStatus
roothub.portstatus [0] = 0x00110103 PRSC CSC PPS PES CCS
Mar 5 07:48:14 nightshade kernel: hub 1-0:1.0: port 1 not enabled, trying
reset again...
Mar 5 07:48:14 nightshade kernel: ohci_hcd 0000:00:0e.2: GetStatus
roothub.portstatus [0] = 0x00110103 PRSC CSC PPS PES CCS
Mar 5 07:48:14 nightshade kernel: hub 1-0:1.0: port 1 not enabled, trying
reset again...
Mar 5 07:48:14 nightshade kernel: hub 1-0:1.0: Cannot enable port 1.
Maybe the USB cable is bad?
Mar 5 07:48:14 nightshade kernel: ohci_hcd 0000:00:0e.2: GetStatus
roothub.portstatus [0] = 0x00110103 PRSC CSC PPS PES CCS
Mar 5 07:48:14 nightshade kernel: hub 1-0:1.0: port 1 not enabled, trying
reset again...
Mar 5 07:48:14 nightshade kernel: ohci_hcd 0000:00:0e.2: GetStatus
roothub.portstatus [0] = 0x00110103 PRSC CSC PPS PES CCS
Mar 5 07:48:14 nightshade kernel: hub 1-0:1.0: port 1 not enabled, trying
reset again...
Mar 5 07:48:14 nightshade kernel: ohci_hcd 0000:00:0e.2: GetStatus
roothub.portstatus [0] = 0x00110103 PRSC CSC PPS PES CCS
Mar 5 07:48:14 nightshade kernel: hub 1-0:1.0: port 1 not enabled, trying
reset again...
Mar 5 07:48:15 nightshade kernel: ohci_hcd 0000:00:0e.2: GetStatus
roothub.portstatus [0] = 0x00110103 PRSC CSC PPS PES CCS
Mar 5 07:48:15 nightshade kernel: hub 1-0:1.0: port 1 not enabled, trying
reset again...
Mar 5 07:48:15 nightshade kernel: ohci_hcd 0000:00:0e.2: GetStatus
roothub.portstatus [0] = 0x00110103 PRSC CSC PPS PES CCS
Mar 5 07:48:15 nightshade kernel: hub 1-0:1.0: port 1 not enabled, trying
reset again...
Mar 5 07:48:15 nightshade kernel: hub 1-0:1.0: Cannot enable port 1.
Maybe the USB cable is bad?
*** To here loops on forever.
-------------------------------------------------------
SF email is sponsored by - The IT Product Guide
Read honest & candid reviews on hundreds of IT Products from real users.
Discover which products truly live up to the hype. Start reading now.
http://ads.osdn.com/?ad_id=6595&alloc_id=14396&op=click
_______________________________________________
[email protected]
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-users
