Quoting Alan Stern <[EMAIL PROTECTED]>:
[...]
Any thoughts on how to go forward from here? I'm running out of disk space
badly!
Post the logs showing what happened.
Ok below is the full log, from it finding the USB controllers through
to the end
of boot in single user mode. The last lines are it finding my USB
CompactFlash
card reader.
I noticed a bit starting with:
uhci_hcd 0000:00:1d.2: uhci_result_control: failed with status 440000
which only sometimes seems to come up, through the uhci_hcd driver will
eventually recognise and let me use the Maxtor drive if I get rid of ehci_hcd,
or unplug it and plug it in enough. WIth just ehci_hcd, it never recognises
it, and in fact after a couple of goes at unplugging and plugging, it ignores
this event completely.
Here are the logs:
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.3
PCI: Found IRQ 11 for device 0000:00:1d.0
PCI: Sharing IRQ 11 with 0000:00:1d.3
PCI: Sharing IRQ 11 with 0000:03:00.0
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: detected 2 ports
uhci_hcd 0000:00:1d.0: check_and_reset_hc: legsup = 0x2f00
uhci_hcd 0000:00:1d.0: Performing full reset
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 11, io base 0x0000e000
usb usb1: default language 0x0409
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: UHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.14 uhci_hcd
usb usb1: SerialNumber: 0000:00:1d.0
usb usb1: hotplug
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: hotplug
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: power on to power good time: 2ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: state 5 ports 2 chg 0000 evt 0000
PCI: Found IRQ 10 for device 0000:00:1d.1
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: detected 2 ports
uhci_hcd 0000:00:1d.1: check_and_reset_hc: legsup = 0x2400
uhci_hcd 0000:00:1d.1: Performing full reset
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 10, io base 0x0000e400
usb usb2: default language 0x0409
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.14 uhci_hcd
usb usb2: SerialNumber: 0000:00:1d.1
usb usb2: hotplug
usb usb2: adding 2-0:1.0 (config #1, interface 0)
usb 2-0:1.0: hotplug
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: individual port over-current protection
hub 2-0:1.0: power on to power good time: 2ms
hub 2-0:1.0: local power source is good
hub 2-0:1.0: state 5 ports 2 chg 0000 evt 0000
PCI: Found IRQ 10 for device 0000:00:1d.2
PCI: Sharing IRQ 10 with 0000:00:1f.1
PCI: Sharing IRQ 10 with 0000:03:02.0
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: detected 2 ports
uhci_hcd 0000:00:1d.2: check_and_reset_hc: legsup = 0x2400
uhci_hcd 0000:00:1d.2: Performing full reset
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 10, io base 0x0000e800
usb usb3: default language 0x0409
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.14 uhci_hcd
usb usb3: SerialNumber: 0000:00:1d.2
usb usb3: hotplug
usb usb3: adding 3-0:1.0 (config #1, interface 0)
usb 3-0:1.0: hotplug
hub 3-0:1.0: usb_probe_interface
hub 3-0:1.0: usb_probe_interface - got id
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
hub 3-0:1.0: standalone hub
hub 3-0:1.0: no power switching (usb 1.0)
hub 3-0:1.0: individual port over-current protection
hub 3-0:1.0: power on to power good time: 2ms
hub 3-0:1.0: local power source is good
hub 3-0:1.0: state 5 ports 2 chg 0000 evt 0000
uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
hub 3-0:1.0: port 2, status 0101, change 0001, 12 Mb/s
PCI: Found IRQ 11 for device 0000:00:1d.3
PCI: Sharing IRQ 11 with 0000:00:1d.0
PCI: Sharing IRQ 11 with 0000:03:00.0
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: detected 2 ports
uhci_hcd 0000:00:1d.3: check_and_reset_hc: legsup = 0x2400
uhci_hcd 0000:00:1d.3: Performing full reset
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 11, io base 0x0000ec00
usb usb4: default language 0x0409
usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.14 uhci_hcd
usb usb4: SerialNumber: 0000:00:1d.3
usb usb4: hotplug
usb usb4: adding 4-0:1.0 (config #1, interface 0)
usb 4-0:1.0: hotplug
hub 4-0:1.0: usb_probe_interface
hub 4-0:1.0: usb_probe_interface - got id
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
hub 4-0:1.0: standalone hub
hub 4-0:1.0: no power switching (usb 1.0)
hub 4-0:1.0: individual port over-current protection
hub 4-0:1.0: power on to power good time: 2ms
hub 4-0:1.0: local power source is good
hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x101
ehci_hcd: block sizes: qh 128 qtd 96 itd 192 sitd 96
PCI: Found IRQ 10 for device 0000:00:1d.7
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: reset hcs_params 0x104208 dbg=1 cc=4 pcc=2 ordered !ppc
ports=8
ehci_hcd 0000:00:1d.7: reset hcc_params 6871 thresh 7 uframes 1024 64 bit addr
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: capability 0001 at 68
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: irq 10, io mem 0xfebffc00
ehci_hcd 0000:00:1d.7: reset command 080002 (park)=0 ithresh=8
period=1024 Reset
HALT
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: unable to enable MWI - not fatal.
ehci_hcd 0000:00:1d.7: init command 010001 (park)=0 ithresh=1 period=1024 RUN
ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
ehci_hcd 0000:00:1d.7: supports USB remote wakeup
usb usb5: default language 0x0409
usb usb5: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: EHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.14 ehci_hcd
usb usb5: SerialNumber: 0000:00:1d.7
usb usb5: hotplug
usb usb5: adding 5-0:1.0 (config #1, interface 0)
usb 5-0:1.0: hotplug
usb 3-2: new full speed USB device using uhci_hcd and address 2
uhci_hcd 0000:00:1d.2: uhci_result_control: failed with status 440000
[f7dc3180] link (37dc3122) element (37dc2040)
0: [f7dc2040] link (37dc2080) e0 Stalled CRC/Timeo Length=7 MaxLen=7 DT0
EndPt=0 Dev=0, PID=2d(SETUP) (buf=37d32600)
1: [f7dc2080] link (37dc20c0) e3 SPD Active Length=0 MaxLen=3f DT1 EndPt=0
Dev=0, PID=69(IN) (buf=023b9180)
2: [f7dc20c0] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1 EndPt=0
Dev=0, PID=e1(OUT) (buf=00000000)
uhci_hcd 0000:00:1d.2: uhci_result_control: failed with status 440000
[f7dc31a0] link (37dc3122) element (37dc2100)
0: [f7dc2100] link (37dc2140) e0 Stalled CRC/Timeo Length=7 MaxLen=7 DT0
EndPt=0 Dev=0, PID=2d(SETUP) (buf=37d32600)
1: [f7dc2140] link (37dc2180) e3 SPD Active Length=0 MaxLen=3f DT1 EndPt=0
Dev=0, PID=69(IN) (buf=023b9180)
2: [f7dc2180] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1 EndPt=0
Dev=0, PID=e1(OUT) (buf=00000000)
uhci_hcd 0000:00:1d.2: uhci_result_control: failed with status 440000
[f7dc3180] link (37dc3122) element (37dc2040)
0: [f7dc2040] link (37dc2080) e0 Stalled CRC/Timeo Length=7 MaxLen=7 DT0
EndPt=0 Dev=0, PID=2d(SETUP) (buf=37d32600)
1: [f7dc2080] link (37dc20c0) e3 SPD Active Length=0 MaxLen=3f DT1 EndPt=0
Dev=0, PID=69(IN) (buf=023b9180)
2: [f7dc20c0] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1 EndPt=0
Dev=0, PID=e1(OUT) (buf=00000000)
hub 5-0:1.0: usb_probe_interface
hub 5-0:1.0: usb_probe_interface - got id
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
hub 5-0:1.0: standalone hub
hub 5-0:1.0: no power switching (usb 1.0)
hub 5-0:1.0: individual port over-current protection
hub 5-0:1.0: Single TT
hub 5-0:1.0: TT requires at most 8 FS bit times (666 ns)
hub 5-0:1.0: power on to power good time: 20ms
hub 5-0:1.0: local power source is good
hub 4-0:1.0: state 5 ports 2 chg 0000 evt 0004
uhci_hcd 0000:00:1d.3: port 2 portsc 0082,00
hub 4-0:1.0: port 2, status 0100, change 0001, 12 Mb/s
hub 4-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100
hub 3-0:1.0: state 5 ports 2 chg 0000 evt 0004
hub 5-0:1.0: state 5 ports 8 chg 0000 evt 0000
ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803 POWER sig=j CSC CONNECT
hub 5-0:1.0: port 6, status 0501, change 0001, 480 Mb/s
hub 5-0:1.0: debounce: port 6: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:1d.7: port 6 full speed --> companion
ehci_hcd 0000:00:1d.7: GetStatus port 6 status 003801 POWER OWNER sig=j
CONNECT
ehci_hcd 0000:00:1d.7: GetStatus port 8 status 001803 POWER sig=j CSC CONNECT
hub 5-0:1.0: port 8, status 0501, change 0001, 480 Mb/s
hub 5-0:1.0: debounce: port 8: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:1d.7: port 8 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 8 status 001005 POWER sig=se0 PE CONNECT
uhci_hcd 0000:00:1d.0: suspend_rh (auto-stop)
usb 5-8: new high speed USB device using ehci_hcd and address 3
ehci_hcd 0000:00:1d.7: devpath 8 ep0in 3strikes
ehci_hcd 0000:00:1d.7: devpath 8 ep0in 3strikes
ehci_hcd 0000:00:1d.7: devpath 8 ep0in 3strikes
ehci_hcd 0000:00:1d.7: port 8 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 8 status 001005 POWER sig=se0 PE CONNECT
usb 5-8: device descriptor read/64, error -71
uhci_hcd 0000:00:1d.1: suspend_rh (auto-stop)
ehci_hcd 0000:00:1d.7: devpath 8 ep0in 3strikes
ehci_hcd 0000:00:1d.7: devpath 8 ep0in 3strikes
ehci_hcd 0000:00:1d.7: devpath 8 ep0in 3strikes
ehci_hcd 0000:00:1d.7: port 8 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 8 status 001005 POWER sig=se0 PE CONNECT
usb 5-8: device descriptor read/64, error -71
ehci_hcd 0000:00:1d.7: port 8 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 8 status 001005 POWER sig=se0 PE CONNECT
usb 5-8: new high speed USB device using ehci_hcd and address 4
ehci_hcd 0000:00:1d.7: devpath 8 ep0in 3strikes
ehci_hcd 0000:00:1d.7: devpath 8 ep0in 3strikes
ehci_hcd 0000:00:1d.7: devpath 8 ep0in 3strikes
ehci_hcd 0000:00:1d.7: port 8 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 8 status 001005 POWER sig=se0 PE CONNECT
usb 5-8: device descriptor read/64, error -71
uhci_hcd 0000:00:1d.3: suspend_rh (auto-stop)
ehci_hcd 0000:00:1d.7: devpath 8 ep0in 3strikes
ehci_hcd 0000:00:1d.7: devpath 8 ep0in 3strikes
ehci_hcd 0000:00:1d.7: devpath 8 ep0in 3strikes
ehci_hcd 0000:00:1d.7: port 8 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 8 status 001005 POWER sig=se0 PE CONNECT
usb 5-8: device descriptor read/64, error -71
ehci_hcd 0000:00:1d.7: port 8 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 8 status 001005 POWER sig=se0 PE CONNECT
usb 5-8: new high speed USB device using ehci_hcd and address 5
ehci_hcd 0000:00:1d.7: devpath 8 ep0in 3strikes
usb 5-8: device descriptor read/all, error -71
ehci_hcd 0000:00:1d.7: port 8 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 8 status 001005 POWER sig=se0 PE CONNECT
usb 5-8: new high speed USB device using ehci_hcd and address 6
ehci_hcd 0000:00:1d.7: devpath 8 ep0in 3strikes
usb 5-8: device descriptor read/all, error -71
hub 3-0:1.0: state 5 ports 2 chg 0000 evt 0004
uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
hub 3-0:1.0: port 2, status 0101, change 0001, 12 Mb/s
hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x101
usb 3-2: new full speed USB device using uhci_hcd and address 3
usb 3-2: ep0 maxpacket = 8
usb 3-2: default language 0x0409
usb 3-2: new device strings: Mfr=2, Product=3, SerialNumber=0
usb 3-2: Product: Mass Storage
usb 3-2: Manufacturer: USB
usb 3-2: hotplug
usb 3-2: adding 3-2:1.0 (config #1, interface 0)
usb 3-2:1.0: hotplug
EXT3 FS on hda1, internal journal
Adding 3389704k swap on /dev/hda2. Priority:-1 extents:1 across:3389704k
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdc1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SCSI subsystem initialized
Initializing USB Mass Storage driver...
usb-storage 3-2:1.0: usb_probe_interface
usb-storage 3-2:1.0: usb_probe_interface - got id
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1313 $ Ben Collins <[EMAIL PROTECTED]>
PCI: Found IRQ 10 for device 0000:03:0a.0
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[10]
MMIO=[feafd800-feafdfff] Max
Packet=[2048]
ieee1394: Host added: ID:BUS[0-00:1023] GUID[000010dc002a2719]
Vendor: Datafab Model: KECF-USB Rev: 0113
Type: Direct-Access ANSI SCSI revision: 02
usb-storage: device scan complete
Thanks
-Matthew
--
+--------------------------------------------------------------------------+
| Matthew Donaldson http://www.datadeliverance.com |
| Data Deliverance Pty. Ltd. Email: [EMAIL PROTECTED] |
| 30 Musgrave Ave. Phone: +61 8 8265 7976 _ |
| Banksia Park Fax: +61 8 8265 0032 John / \/ |
| South Australia 5091 3:16 \_/\ |
+--------------------------------------------------------------------------+
--------------------------------------------------
This message was sent using Adam Internet Webmail.
-------------------------------------------------------
This SF.Net email is sponsored by the JBoss Inc. Get Certified Today
Register for a JBoss Training Course. Free Certification Exam
for All Training Attendees Through End of 2005. For more info visit:
http://ads.osdn.com/?ad_id=7628&alloc_id=16845&op=click
_______________________________________________
[email protected]
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-users
