Alan Stern wrote:
No, the logs have too much irrelevant information and not enough relevant
information.
Instead, do this. First, turn on CONFIG_USB_DEBUG in the kernel
configuration and rebuild the USB drivers. Also, don't use the ub driver;
use usb-storage instead. (It wouldn't hurt to turn on
CONFIG_USB_STORAGE_DEBUG as well.)
Unplug all your USB devices except the card reader, the USB-2.0 hub, and
the mouse attached to the hub. Then after rebooting, do
rmmod uhci-hcd
rmmod ehci-hcd
dmesg -c >/dev/null
modprobe ehci-hcd
After everything settles down, make a copy of the output from dmesg.
Then do something to cause an error on the card reader, and again copy the
output from dmesg. Post both of those logs.
Alan Stern
Here the logs as requested (hopefully correct this time):
==============================================================
Before error occures it looks like this:
==============================================================
ehci_hcd: block sizes: qh 128 qtd 96 itd 192 sitd 96
ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1d.7: Intel Corp. 6300ESB USB2 Enhanced Host Controller
ehci_hcd 0000:00:1d.7: reset hcs_params 0x102204 dbg=1 cc=2 pcc=2 ordered !ppc
ports=4
ehci_hcd 0000:00:1d.7: reset hcc_params 6871 thresh 7 uframes 1024 64 bit addr
ehci_hcd 0000:00:1d.7: capability 0001 at 68
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: irq 23, pci mem 0xdc001400
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: reset command 080002 (park)=0 ithresh=8 period=1024
Reset HALT
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: init command 010001 (park)=0 ithresh=1 period=1024 RUN
ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
ehci_hcd 0000:00:1d.7: supports USB remote wakeup
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: default language 0x0409
usb usb1: Product: Intel Corp. 6300ESB USB2 Enhanced Host Controller
usb usb1: Manufacturer: Linux 2.6.11.3 ehci_hcd
usb usb1: SerialNumber: 0000:00:1d.7
usb usb1: hotplug
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: hotplug
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: ganged power switching
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: Single TT
hub 1-0:1.0: TT requires at most 8 FS bit times
hub 1-0:1.0: power on to power good time: 20ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: enabling power on all ports
hub 1-0:1.0: state 5 ports 4 chg 001e evt 001f
hub 1-0:1.0: port 1, status 0100, change 0000, 12 Mb/s
hub 1-0:1.0: port 2, status 0100, change 0000, 12 Mb/s
ehci_hcd 0000:00:1d.7: GetStatus port 3 status 001803 POWER sig=j CSC CONNECT
hub 1-0:1.0: port 3, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:1d.7: port 3 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 3 status 001005 POWER sig=se0 PE CONNECT
usb 1-3: new high speed USB device using ehci_hcd and address 2
ehci_hcd 0000:00:1d.7: port 3 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 3 status 001005 POWER sig=se0 PE CONNECT
usb 1-3: new device strings: Mfr=0, Product=0, SerialNumber=0
usb 1-3: hotplug
usb 1-3: adding 1-3:1.0 (config #1, interface 0)
usb 1-3:1.0: hotplug
hub 1-3:1.0: usb_probe_interface
hub 1-3:1.0: usb_probe_interface - got id
hub 1-3:1.0: USB hub found
hub 1-3:1.0: 4 ports detected
hub 1-3:1.0: compound device; port removable status: FFFF
hub 1-3:1.0: individual port power switching
hub 1-3:1.0: individual port over-current protection
hub 1-3:1.0: Single TT
hub 1-3:1.0: TT requires at most 16 FS bit times
hub 1-3:1.0: power on to power good time: 100ms
hub 1-3:1.0: local power source is good
hub 1-3:1.0: enabling power on all ports
usb 1-3: link qh256-0001/f5e68100 start 255 [7/0 us]
ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 1-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:1d.7: port 4 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001005 POWER sig=se0 PE CONNECT
usb 1-4: new high speed USB device using ehci_hcd and address 3
ehci_hcd 0000:00:1d.7: port 4 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001005 POWER sig=se0 PE CONNECT
usb 1-4: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-4: default language 0x0409
usb 1-4: Product: Winter Ver1.3
usb 1-4: Manufacturer: Ltd
usb 1-4: SerialNumber: 825917307816
usb 1-4: hotplug
usb 1-4: adding 1-4:1.0 (config #1, interface 0)
usb 1-4:1.0: hotplug
usb-storage 1-4:1.0: usb_probe_interface
usb-storage 1-4:1.0: usb_probe_interface - got id
usb-storage: USB Mass Storage device detected
usb-storage: -- associate_dev
usb-storage: Vendor: 0x07cc, Product: 0x0301, Revision: 0x0005
usb-storage: Interface Subclass: 0x06, Protocol: 0x50
usb-storage: Vendor: Ltd, Product: Winter Ver1.3
usb-storage: Transport: Bulk
usb-storage: Protocol: Transparent SCSI
usb-storage: usb_stor_control_msg: rq=fe rqtype=a1 value=0000 index=00 len=1
usb-storage: GetMaxLUN command result is 1, data is 1
usb-storage: *** thread sleeping.
scsi5 : SCSI emulation for USB Mass Storage devices
hub 1-0:1.0: state 5 ports 4 chg 0000 evt 0000
hub 1-3:1.0: state 5 ports 4 chg 001e evt 0004
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
hub 1-3:1.0: port 1, status 0100, change 0000, 12 Mb/s
hub 1-3:1.0: port 2, status 0301, change 0001, 1.5 Mb/s
hub 1-3:1.0: debounce: port 2: total 100ms stable 100ms status 0x301
usb 1-3.2: new low speed USB device using ehci_hcd and address 4
usb 1-3.2: skipped 1 descriptor after interface
usb 1-3.2: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-3.2: default language 0x0409
usb 1-3.2: Product: USB-PS/2 Optical Mouse
usb 1-3.2: Manufacturer: Logitech
usb 1-3.2: hotplug
usb 1-3.2: adding 1-3.2:1.0 (config #1, interface 0)
usb 1-3.2:1.0: hotplug
usbhid 1-3.2:1.0: usb_probe_interface
usbhid 1-3.2:1.0: usb_probe_interface - got id
usb 1-3.2: link qh8-0601/f5e68280 start 7 [8/15 us]
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on
usb-0000:00:1d.7-3.2
hub 1-3:1.0: port 3, status 0100, change 0000, 12 Mb/s
hub 1-3:1.0: port 4, status 0100, change 0000, 12 Mb/s
hub 1-3:1.0: state 5 ports 4 chg 0000 evt 0004
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command INQUIRY (6 bytes)
usb-storage: 12 00 00 00 24 00
usb-storage: Bulk Command S 0x43425355 T 0x14f1 L 36 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_buf: xfer 36 bytes
usb-storage: Status code 0; transferred 36/36
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x14f1 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
Vendor: USB2.0 Model: CardReader CF RW Rev: 0814
Type: Direct-Access ANSI SCSI revision: 00
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x14f2 L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x14f2 R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x800014f2 L 18 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_buf: xfer 18 bytes
usb-storage: Status code 0; transferred 18/18
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x800014f2 R 0 Stat 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x2, ASC: 0x3a, ASCQ: 0x0
usb-storage: (Unknown Key): (unknown ASC/ASCQ)
usb-storage: scsi cmd done, result=0x2
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x14f3 L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x14f3 R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x800014f3 L 18 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_buf: xfer 18 bytes
usb-storage: Status code 0; transferred 18/18
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x800014f3 R 0 Stat 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x2, ASC: 0x3a, ASCQ: 0x0
usb-storage: (Unknown Key): (unknown ASC/ASCQ)
usb-storage: scsi cmd done, result=0x2
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x14f4 L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x14f4 R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x800014f4 L 18 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_buf: xfer 18 bytes
usb-storage: Status code 0; transferred 18/18
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x800014f4 R 0 Stat 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x2, ASC: 0x3a, ASCQ: 0x0
usb-storage: (Unknown Key): (unknown ASC/ASCQ)
usb-storage: scsi cmd done, result=0x2
usb-storage: *** thread sleeping.
Attached scsi removable disk sdb at scsi5, channel 0, id 0, lun 0
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command INQUIRY (6 bytes)
usb-storage: 12 20 00 00 24 00
usb-storage: Bulk Command S 0x43425355 T 0x14f5 L 36 F 128 Trg 0 LUN 1 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_buf: xfer 36 bytes
usb-storage: Status code 0; transferred 36/36
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x14f5 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
Vendor: USB2.0 Model: CardReader Combo Rev: 0814
Type: Direct-Access ANSI SCSI revision: 00
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 20 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x14f6 L 0 F 0 Trg 0 LUN 1 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x14f6 R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x800014f6 L 18 F 128 Trg 0 LUN 1 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_buf: xfer 18 bytes
usb-storage: Status code 0; transferred 18/18
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x800014f6 R 0 Stat 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x2, ASC: 0x3a, ASCQ: 0x0
usb-storage: (Unknown Key): (unknown ASC/ASCQ)
usb-storage: scsi cmd done, result=0x2
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 20 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x14f7 L 0 F 0 Trg 0 LUN 1 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x14f7 R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x800014f7 L 18 F 128 Trg 0 LUN 1 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_buf: xfer 18 bytes
usb-storage: Status code 0; transferred 18/18
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x800014f7 R 0 Stat 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x2, ASC: 0x3a, ASCQ: 0x0
usb-storage: (Unknown Key): (unknown ASC/ASCQ)
usb-storage: scsi cmd done, result=0x2
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 20 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x14f8 L 0 F 0 Trg 0 LUN 1 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x14f8 R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x800014f8 L 18 F 128 Trg 0 LUN 1 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_buf: xfer 18 bytes
usb-storage: Status code 0; transferred 18/18
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x800014f8 R 0 Stat 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x2, ASC: 0x3a, ASCQ: 0x0
usb-storage: (Unknown Key): (unknown ASC/ASCQ)
usb-storage: scsi cmd done, result=0x2
usb-storage: *** thread sleeping.
Attached scsi removable disk sdc at scsi5, channel 0, id 0, lun 1
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad LUN (0:2)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (1:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (2:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (3:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (4:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (5:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (6:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (7:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: device scan complete
==============================================================
After error dmesg shows the following:
==============================================================
Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 3d 00 00 40 00
usb-storage: Bulk Command S 0x43425355 T 0x1648 L 32768 F 128 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 32768 bytes, 1 entries
usb-storage: Status code 0; transferred 32768/32768
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x1648 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command ALLOW_MEDIUM_REMOVAL (6 bytes)
usb-storage: 1e 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x1649 L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x1649 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x164a L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x164a R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command ALLOW_MEDIUM_REMOVAL (6 bytes)
usb-storage: 1e 00 00 00 01 00
usb-storage: Bulk Command S 0x43425355 T 0x164b L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x164b R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 3f 00 00 02 00
usb-storage: Bulk Command S 0x43425355 T 0x164c L 1024 F 128 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 1024 bytes, 1 entries
usb-storage: Status code 0; transferred 1024/1024
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x164c R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 3d 00 00 08 00
usb-storage: Bulk Command S 0x43425355 T 0x164d L 4096 F 128 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096 bytes, 1 entries
usb-storage: Status code 0; transferred 4096/4096
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x164d R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 45 00 00 08 00
usb-storage: Bulk Command S 0x43425355 T 0x164e L 4096 F 128 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096 bytes, 1 entries
usb-storage: Status code 0; transferred 4096/4096
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x164e R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 5d 00 00 08 00
usb-storage: Bulk Command S 0x43425355 T 0x164f L 4096 F 128 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096 bytes, 1 entries
usb-storage: Status code 0; transferred 4096/4096
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x164f R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 0f fd 00 00 08 00
usb-storage: Bulk Command S 0x43425355 T 0x165f L 4096 F 128 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096 bytes, 1 entries
usb-storage: Status code 0; transferred 4096/4096
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x165f R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 04 00 5d 00 00 08 00
usb-storage: Bulk Command S 0x43425355 T 0x1660 L 4096 F 128 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096 bytes, 1 entries
usb-storage: Status code 0; transferred 4096/4096
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x1660 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command WRITE_10 (10 bytes)
usb-storage: 2a 00 00 00 00 3d 00 00 08 00
usb-storage: Bulk Command S 0x43425355 T 0x1662 L 4096 F 0 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096 bytes, 1 entries
usb-storage: Status code 0; transferred 4096/4096
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x1662 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 10 05 00 00 08 00
usb-storage: Bulk Command S 0x43425355 T 0x16a1 L 4096 F 128 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096 bytes, 1 entries
usb-storage: Status code 0; transferred 4096/4096
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x16a1 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 10 0d 00 00 08 00
usb-storage: Bulk Command S 0x43425355 T 0x16a2 L 4096 F 128 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096 bytes, 1 entries
usb-storage: Status code 0; transferred 4096/4096
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x16a2 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 10 15 00 00 08 00
usb-storage: Bulk Command S 0x43425355 T 0x16a3 L 4096 F 128 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096 bytes, 1 entries
usb-storage: Status code 0; transferred 4096/4096
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x16a3 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 10 1d 00 00 08 00
usb-storage: Bulk Command S 0x43425355 T 0x16a4 L 4096 F 128 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096 bytes, 1 entries
usb-storage: Status code 0; transferred 4096/4096
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x16a4 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 4d 00 00 08 00
usb-storage: Bulk Command S 0x43425355 T 0x16a5 L 4096 F 128 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096 bytes, 1 entries
usb-storage: Status code 0; transferred 4096/4096
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x16a5 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 55 00 00 08 00
usb-storage: Bulk Command S 0x43425355 T 0x16a6 L 4096 F 128 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096 bytes, 1 entries
usb-storage: Status code 0; transferred 4096/4096
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x16a6 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command WRITE_10 (10 bytes)
usb-storage: 2a 00 00 00 00 3d 00 00 28 00
usb-storage: Bulk Command S 0x43425355 T 0x16af L 20480 F 0 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 20480 bytes, 4 entries
usb-storage: Status code 0; transferred 20480/20480
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x16af R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x800016af L 18 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_buf: xfer 18 bytes
usb-storage: Status code 0; transferred 18/18
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x800016af R 0 Stat 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x4, ASC: 0x4b, ASCQ: 0x0
usb-storage: (Unknown Key): (unknown ASC/ASCQ)
usb-storage: scsi cmd done, result=0x2
usb-storage: *** thread sleeping.
SCSI error : <5 0 0 0> return code = 0x8000002
sdb: Current: sense key=0x4
ASC=0x4b ASCQ=0x0
end_request: I/O error, dev sdb, sector 61
Buffer I/O error on device sdb1, logical block 0
lost page write due to I/O error on sdb1
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command WRITE_10 (10 bytes)
usb-storage: 2a 00 00 00 00 45 00 00 20 00
usb-storage: Bulk Command S 0x43425355 T 0x16b0 L 16384 F 0 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 16384 bytes, 4 entries
usb-storage: Status code -32; transferred 1536/16384
usb-storage: clearing endpoint halt for pipe 0xc0010300
usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=02 len=0
usb-storage: usb_stor_clear_halt: result = 0
usb-storage: Bulk data transfer result 0x2
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x16b0 R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: -- unexpectedly short transfer
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x800016b0 L 18 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_buf: xfer 18 bytes
usb-storage: command_abort called
usb-storage: usb_stor_stop_transport called
usb-storage: -- cancelling URB
usb-storage: Status code -104; transferred 0/18
usb-storage: -- transfer cancelled
usb-storage: Bulk data transfer result 0x4
usb-storage: -- auto-sense aborted
usb-storage: usb_stor_Bulk_reset called
usb-storage: usb_stor_control_msg: rq=ff rqtype=21 value=0000 index=00 len=0
usb-storage: Soft reset: clearing bulk-in endpoint halt
usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=81 len=0
usb-storage: usb_stor_clear_halt: result = 0
usb-storage: Soft reset: clearing bulk-out endpoint halt
usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=02 len=0
usb-storage: usb_stor_clear_halt: result = 0
usb-storage: Soft reset done
usb-storage: scsi command aborted
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x16b0 L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: command_abort called
usb-storage: usb_stor_stop_transport called
usb-storage: -- cancelling URB
usb-storage: Status code -104; transferred 0/13
usb-storage: -- transfer cancelled
usb-storage: Bulk status result = 4
usb-storage: -- command was aborted
usb-storage: usb_stor_Bulk_reset called
usb-storage: usb_stor_control_msg: rq=ff rqtype=21 value=0000 index=00 len=0
usb-storage: Soft reset: clearing bulk-in endpoint halt
usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=81 len=0
usb-storage: usb_stor_clear_halt: result = 0
usb-storage: Soft reset: clearing bulk-out endpoint halt
usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=02 len=0
usb-storage: usb_stor_clear_halt: result = 0
usb-storage: Soft reset done
usb-storage: scsi command aborted
usb-storage: *** thread sleeping.
usb-storage: device_reset called
usb-storage: usb_stor_Bulk_reset called
usb-storage: usb_stor_control_msg: rq=ff rqtype=21 value=0000 index=00 len=0
usb-storage: Soft reset: clearing bulk-in endpoint halt
usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=81 len=0
usb-storage: usb_stor_clear_halt: result = 0
usb-storage: Soft reset: clearing bulk-out endpoint halt
usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=02 len=0
usb-storage: usb_stor_clear_halt: result = 0
usb-storage: Soft reset done
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x16b0 L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: command_abort called
usb-storage: usb_stor_stop_transport called
usb-storage: -- cancelling URB
usb-storage: Status code -104; transferred 0/13
usb-storage: -- transfer cancelled
usb-storage: Bulk status result = 4
usb-storage: -- command was aborted
usb-storage: usb_stor_Bulk_reset called
usb-storage: usb_stor_control_msg: rq=ff rqtype=21 value=0000 index=00 len=0
usb-storage: Soft reset: clearing bulk-in endpoint halt
usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=81 len=0
usb-storage: usb_stor_clear_halt: result = 0
usb-storage: Soft reset: clearing bulk-out endpoint halt
usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=02 len=0
usb-storage: usb_stor_clear_halt: result = 0
usb-storage: Soft reset done
usb-storage: scsi command aborted
usb-storage: *** thread sleeping.
usb-storage: bus_reset called
ehci_hcd 0000:00:1d.7: port 4 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001005 POWER sig=se0 PE CONNECT
usb 1-4: reset high speed USB device using ehci_hcd and address 3
ehci_hcd 0000:00:1d.7: port 4 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001005 POWER sig=se0 PE CONNECT
usb-storage: usb_reset_device returns 0
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x16b0 L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x16b0 R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x800016b0 L 18 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_buf: xfer 18 bytes
usb-storage: Status code 0; transferred 18/18
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x800016b0 R 0 Stat 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x2, ASC: 0x3a, ASCQ: 0x0
usb-storage: (Unknown Key): (unknown ASC/ASCQ)
usb-storage: scsi cmd done, result=0x2
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x16b0 L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x16b0 R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x800016b0 L 18 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_buf: xfer 18 bytes
usb-storage: Status code 0; transferred 18/18
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x800016b0 R 0 Stat 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x2, ASC: 0x3a, ASCQ: 0x0
usb-storage: (Unknown Key): (unknown ASC/ASCQ)
usb-storage: scsi cmd done, result=0x2
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command ALLOW_MEDIUM_REMOVAL (6 bytes)
usb-storage: 1e 00 00 00 01 00
usb-storage: Bulk Command S 0x43425355 T 0x16ff L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x16ff R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x800016ff L 18 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_buf: xfer 18 bytes
usb-storage: Status code 0; transferred 18/18
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x800016ff R 0 Stat 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x2, ASC: 0x3a, ASCQ: 0x0
usb-storage: (Unknown Key): (unknown ASC/ASCQ)
usb-storage: scsi cmd done, result=0x2
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command WRITE_10 (10 bytes)
usb-storage: 2a 00 00 00 00 45 00 00 20 00
usb-storage: Bulk Command S 0x43425355 T 0x1700 L 16384 F 0 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 16384 bytes, 4 entries
usb-storage: Status code -32; transferred 512/16384
usb-storage: clearing endpoint halt for pipe 0xc0010300
usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=02 len=0
usb-storage: usb_stor_clear_halt: result = 0
usb-storage: Bulk data transfer result 0x2
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x1700 R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: -- unexpectedly short transfer
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x80001700 L 18 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_buf: xfer 18 bytes
usb-storage: Status code -32; transferred 0/18
usb-storage: clearing endpoint halt for pipe 0xc0008380
usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=81 len=0
usb-storage: usb_stor_clear_halt: result = 0
usb-storage: Bulk data transfer result 0x2
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code -32; transferred 0/13
usb-storage: clearing endpoint halt for pipe 0xc0008380
usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=81 len=0
usb-storage: usb_stor_clear_halt: result = 0
usb-storage: Attempting to get CSW (2nd try)...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
=========================================================================
dmesg logfile seems to be truncated in error case somehow, I think this is
regular behaviour?
Another think I can definitely exclude from possible error list is cabling and
hardware (besides motherboard). We checked different USB2.0 cabling, card
readers, mice, and hubs. The error stayed always the same. When looking at
USB2.0 signaling with an high end oscilloscope signal quality is definitely
within limits.
I still think we have an EHCI hardware or driver timing issue here. We can see
a correlation between low speed bandwidth an error frequency. And error
occures only when writing to device.
Another interesting aspect just occured today: when testing exactly same setup
but with external USB2.0 harddisk instead of card reader, *no* such errors
occured!
Is there a general "card reader issue" with USB2.0? Because meanwhile we have
tested about 6 different internal and external card readers, having all the
same problem. Those different card readers definitely had at least 4 different
chip sets.
Thomas
--
Thomas Thanner
Manager System Development
Citron GmbH
Anwaltinger Str. 14
D-86165 Augsburg
Tel. : ++49-821-74945-0
Fax. : ++49-821-74945-99
Email: [EMAIL PROTECTED]
http://www.citron.de
-------------------------------------------------------
This SF.net email is sponsored by: Splunk Inc. Do you grep through log files
for problems? Stop! Download the new AJAX search engine that makes
searching your log files as easy as surfing the web. DOWNLOAD SPLUNK!
http://sel.as-us.falkag.net/sel?cmd=lnk&kid=103432&bid=230486&dat=121642
_______________________________________________
[email protected]
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-users
