Hello All,

This problem has cropped up once or twice on the lists before but with 
no apparent resolution.   The problem is basically this: sometime after 
booting -- could be as little as five minutes, could be as long as five 
hours or more -- my USB mouse becomes very sluggish and jerky. I get the 
impression that events for it are queuing up for some period (a second?) 
before being delivered.   If I have  USB keyboard connected as well then 
using that becomes "interesting" -- keypress events take a long time to 
get through, are sometimes ignored and sometimes doubled.

I've scoured the web and the kernel change-logs for any hint of what 
could be wrong but I've turned nothing up.

Back in January, there was a similar thread which included this possible 
patch http://article.gmane.org/gmane.linux.usb.user/14559 -- (the VIA 
no-shutdown-on-babble-patch, not the one linked to) which I applied to a 
2.6.18-rc7 kernel without much optimism.   My lack of optimism stems 
from the fact that I've tried disabling the ehci-hcd driver to no 
effect, I still get the problem.

The hardware I have I believe is identical, or nearly identical, to the 
same problem machine back in January.  It's a Clevo D900K (actually 
badged as a Rock Extreme 64) normally with 2Gb memory in it.  It 
presently has 1Gb as one of the modules has gone bad and that didn't 
make a scrap of difference to the problem.

lspci shows this:

   00:00.0 Host bridge: VIA Technologies, Inc. K8T890 Host Bridge
   00:00.1 Host bridge: VIA Technologies, Inc. K8T890 Host Bridge
   00:00.2 Host bridge: VIA Technologies, Inc. K8T890 Host Bridge
   00:00.3 Host bridge: VIA Technologies, Inc. K8T890 Host Bridge
   00:00.4 Host bridge: VIA Technologies, Inc. K8T890 Host Bridge
   00:00.5 PIC: VIA Technologies, Inc. K8T890 I/O APIC Interrupt Controller
   00:00.7 Host bridge: VIA Technologies, Inc. K8T890 Host Bridge
   00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI bridge [K8T800/K8T890 
South]
   00:02.0 PCI bridge: VIA Technologies, Inc. K8T890 PCI to PCI Bridge 
Controller
   00:03.0 PCI bridge: VIA Technologies, Inc. K8T890 PCI to PCI Bridge 
Controller
   00:03.2 PCI bridge: VIA Technologies, Inc. K8T890 PCI to PCI Bridge 
Controller
   00:05.0 CardBus bridge: ENE Technology Inc CB1410 Cardbus Controller (rev 01)
   00:06.0 FireWire (IEEE 1394): Texas Instruments TSB43AB22/A IEEE-1394a-2000 
Controller (PHY/Link)
   00:08.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169 
Gigabit Ethernet (rev 10)
   00:0a.0 Network controller: RaLink Ralink RT2500 802.11G Cardbus/mini-PCI 
(rev 01)
   00:0f.0 RAID bus controller: VIA Technologies, Inc. VIA VT6420 SATA RAID 
Controller (rev 80)
   00:0f.1 IDE interface: VIA Technologies, Inc. 
VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
   00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 
Controller (rev 81)
   00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 
Controller (rev 81)
   00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 
Controller (rev 81)
   00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 
Controller (rev 81)
   00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86)
   00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge 
[KT600/K8T800/K8T890 South]
   00:11.5 Multimedia audio controller: VIA Technologies, Inc. 
VT8233/A/8235/8237 AC97 Audio Controller (rev 60)
   00:11.6 Communication controller: VIA Technologies, Inc. AC'97 Modem 
Controller (rev 80)
   00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] 
HyperTransport Technology Configuration
   00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] 
Address Map
   00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM 
Controller
   00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] 
Miscellaneous Control
   02:00.0 VGA compatible controller: nVidia Corporation GE Force Go 7800 GTX 
(rev a1)

and when the problem shows up, I see this in the following dmesg output 
(I've got CONFIG_USB_DEBUG turned on.  I suspect that the first part is 
the most interesting (especially "usb 1-4: usb-storage timed out on 
ep0in len=18/64").  I do have a card-reader in this machine and I've 
tried disabling it in the BIOS and it makes no difference.   The output 
here is with both the ehci-hcd module loaded and the card-reader enabled 
(but not in use).

    ehci_hcd 0000:00:10.4: port 4 high speed
    ehci_hcd 0000:00:10.4: GetStatus port 4 status 001005 POWER sig=se0 PE 
CONNECT
    usb 1-4: reset high speed USB device using ehci_hcd and address 4
    usb 1-4: usb-storage timed out on ep0in len=18/64
    ehci_hcd 0000:00:10.4: port 4 high speed
    ehci_hcd 0000:00:10.4: GetStatus port 4 status 001005 POWER sig=se0 PE 
CONNECT
    usb 1-4: usb-storage timed out on ep0out len=0/0
    usb 1-4: usb-storage timed out on ep0out len=0/0
    usb 1-4: device not accepting address 4, error -110
    ehci_hcd 0000:00:10.4: port 4 high speed
    ehci_hcd 0000:00:10.4: GetStatus port 4 status 001005 POWER sig=se0 PE 
CONNECT
    usb 1-4: reset high speed USB device using ehci_hcd and address 4
    usb 1-4: usb-storage timed out on ep0in len=18/64
    ehci_hcd 0000:00:10.4: port 4 high speed
    ehci_hcd 0000:00:10.4: GetStatus port 4 status 001005 POWER sig=se0 PE 
CONNECT
    usb 1-4: usb-storage timed out on ep0out len=0/0
    usb 1-4: usb-storage timed out on ep0out len=0/0
    usb 1-4: device not accepting address 4, error -110
    ehci_hcd 0000:00:10.4: port 4 high speed
    ehci_hcd 0000:00:10.4: GetStatus port 4 status 001005 POWER sig=se0 PE 
CONNECT
    usb 1-4: reset high speed USB device using ehci_hcd and address 4
    usb 1-4: usb-storage timed out on ep0out len=0/0
    usb 1-4: usb-storage timed out on ep0out len=0/0
    usb 1-4: device not accepting address 4, error -110
    ehci_hcd 0000:00:10.4: port 4 high speed
    ehci_hcd 0000:00:10.4: GetStatus port 4 status 001005 POWER sig=se0 PE 
CONNECT
    usb 1-4: reset high speed USB device using ehci_hcd and address 4
    usb 1-4: usb-storage timed out on ep0out len=0/0
    usb 1-4: usb-storage timed out on ep0out len=0/0
    usb 1-4: device not accepting address 4, error -110
    hub 1-0:1.0: logical disconnect on port 4
    hub 1-0:1.0: state 7 ports 8 chg 0010 evt 0000
    hub 1-0:1.0: port 4, status 0501, change 0000, 480 Mb/s
    sd 2:0:0:1: scsi: Device offlined - not ready after error recovery
    usb 1-4: USB disconnect, address 4
    usb 1-4: usb_disable_device nuking all URBs
    usb 1-4: unregistering interface 1-4:1.0
    PM: Removing info for No Bus:usbdev1.4_ep01
     usbdev1.4_ep01: ep_device_release called for usbdev1.4_ep01
    PM: Removing info for No Bus:usbdev1.4_ep82
     usbdev1.4_ep82: ep_device_release called for usbdev1.4_ep82
    PM: Removing info for scsi:2:0:0:0
    PM: Removing info for scsi:2:0:0:1
    PM: Removing info for scsi:2:0:0:2
    PM: Removing info for scsi:2:0:0:3
    PM: Removing info for No Bus:host2
    PM: Removing info for usb:1-4:1.0
    usb 1-4:1.0: uevent
    usb 1-4: unregistering device
    PM: Removing info for No Bus:usbdev1.4_ep00
     usbdev1.4_ep00: ep_device_release called for usbdev1.4_ep00
    PM: Removing info for usb:1-4
    usb 1-4: uevent
    scsi 2:0:0:1: rejecting I/O to dead device
    scsi 2:0:0:1: rejecting I/O to dead device
    scsi 2:0:0:1: rejecting I/O to dead device
    scsi 2:0:0:1: rejecting I/O to dead device
    sdb : READ CAPACITY failed.
    sdb : status=0, message=00, host=1, driver=00 
    sdb : sense not available. 
    scsi 2:0:0:1: rejecting I/O to dead device
    sdb: Write Protect is off
    sdb: Mode Sense: 00 00 00 00
    sdb: assuming drive cache: write through
    scsi 2:0:0:1: rejecting I/O to dead device
    scsi 2:0:0:1: rejecting I/O to dead device
    scsi 2:0:0:1: rejecting I/O to dead device
    scsi 2:0:0:1: rejecting I/O to dead device
    scsi 2:0:0:1: rejecting I/O to dead device
    sdb : READ CAPACITY failed.
    sdb : status=0, message=00, host=1, driver=00 
    sdb : sense not available. 
    scsi 2:0:0:1: rejecting I/O to dead device
    sdb: Write Protect is off
    sdb: Mode Sense: 00 00 00 00
    sdb: assuming drive cache: write through
     sdb:<3>scsi 2:0:0:1: rejecting I/O to dead device
    Buffer I/O error on device sdb, logical block 0
    scsi 2:0:0:1: rejecting I/O to dead device
    Buffer I/O error on device sdb, logical block 0
    scsi 2:0:0:1: rejecting I/O to dead device
    Buffer I/O error on device sdb, logical block 0
     unable to read partition table
    scsi 2:0:0:1: rejecting I/O to dead device
    scsi 2:0:0:0: rejecting I/O to dead device
    scsi 2:0:0:0: rejecting I/O to dead device
    scsi 2:0:0:0: rejecting I/O to dead device
    sda : READ CAPACITY failed.
    sda : status=0, message=00, host=1, driver=00 
    sda : sense not available. 
    scsi 2:0:0:0: rejecting I/O to dead device
    sda: Write Protect is off
    sda: Mode Sense: 00 00 00 00
    sda: assuming drive cache: write through
    scsi 2:0:0:0: rejecting I/O to dead device
    scsi 2:0:0:0: rejecting I/O to dead device
    scsi 2:0:0:0: rejecting I/O to dead device
    scsi 2:0:0:0: rejecting I/O to dead device
    scsi 2:0:0:0: rejecting I/O to dead device
    sda : READ CAPACITY failed.
    sda : status=0, message=00, host=1, driver=00 
    sda : sense not available. 
    scsi 2:0:0:0: rejecting I/O to dead device
    sda: Write Protect is off
    sda: Mode Sense: 00 00 00 00
    sda: assuming drive cache: write through
     sda:<3>scsi 2:0:0:0: rejecting I/O to dead device
    Buffer I/O error on device sda, logical block 0
    scsi 2:0:0:0: rejecting I/O to dead device
    Buffer I/O error on device sda, logical block 0
    scsi 2:0:0:0: rejecting I/O to dead device
    Buffer I/O error on device sda, logical block 0
     unable to read partition table
    scsi 2:0:0:0: rejecting I/O to dead device
    scsi 2:0:0:2: rejecting I/O to dead device
    scsi 2:0:0:2: rejecting I/O to dead device
    scsi 2:0:0:2: rejecting I/O to dead device
    sdc : READ CAPACITY failed.
    sdc : status=0, message=00, host=1, driver=00 
    sdc : sense not available. 
    scsi 2:0:0:2: rejecting I/O to dead device
    sdc: Write Protect is off
    sdc: Mode Sense: 00 00 00 00
    sdc: assuming drive cache: write through
    scsi 2:0:0:2: rejecting I/O to dead device
    scsi 2:0:0:2: rejecting I/O to dead device
    scsi 2:0:0:2: rejecting I/O to dead device
    scsi 2:0:0:2: rejecting I/O to dead device
    scsi 2:0:0:2: rejecting I/O to dead device
    sdc : READ CAPACITY failed.
    sdc : status=0, message=00, host=1, driver=00 
    sdc : sense not available. 
    scsi 2:0:0:2: rejecting I/O to dead device
    sdc: Write Protect is off
    sdc: Mode Sense: 00 00 00 00
    sdc: assuming drive cache: write through
     sdc:<3>scsi 2:0:0:2: rejecting I/O to dead device
    Buffer I/O error on device sdc, logical block 0
    scsi 2:0:0:2: rejecting I/O to dead device
    Buffer I/O error on device sdc, logical block 0
    scsi 2:0:0:2: rejecting I/O to dead device
    Buffer I/O error on device sdc, logical block 0
     unable to read partition table
    scsi 2:0:0:2: rejecting I/O to dead device
    scsi 2:0:0:3: rejecting I/O to dead device
    scsi 2:0:0:3: rejecting I/O to dead device
    scsi 2:0:0:3: rejecting I/O to dead device
    scsi 2:0:0:3: rejecting I/O to dead device
    sdd : READ CAPACITY failed.
    sdd : status=0, message=00, host=1, driver=00 
    sdd : sense not available. 
    scsi 2:0:0:3: rejecting I/O to dead device
    sdd: Write Protect is off
    sdd: Mode Sense: 00 00 00 00
    sdd: assuming drive cache: write through
    scsi 2:0:0:3: rejecting I/O to dead device
    scsi 2:0:0:3: rejecting I/O to dead device
    scsi 2:0:0:3: rejecting I/O to dead device
    scsi 2:0:0:3: rejecting I/O to dead device
    scsi 2:0:0:3: rejecting I/O to dead device
    sdd : READ CAPACITY failed.
    sdd : status=0, message=00, host=1, driver=00 
    sdd : sense not available. 
    scsi 2:0:0:3: rejecting I/O to dead device
    sdd: Write Protect is off
    sdd: Mode Sense: 00 00 00 00
    sdd: assuming drive cache: write through
     sdd:<3>scsi 2:0:0:3: rejecting I/O to dead device
    Buffer I/O error on device sdd, logical block 0
    scsi 2:0:0:3: rejecting I/O to dead device
    scsi 2:0:0:3: rejecting I/O to dead device
     unable to read partition table
    scsi 2:0:0:3: rejecting I/O to dead device
    PM: Removing info for No Bus:target2:0:0
    ehci_hcd 0000:00:10.4: port 4 high speed
    ehci_hcd 0000:00:10.4: GetStatus port 4 status 001005 POWER sig=se0 PE 
CONNECT
    usb 1-4: new high speed USB device using ehci_hcd and address 6
    usb 1-4: khubd timed out on ep0in len=18/64
    ehci_hcd 0000:00:10.4: port 4 high speed
    ehci_hcd 0000:00:10.4: GetStatus port 4 status 001005 POWER sig=se0 PE 
CONNECT
    usb 1-4: khubd timed out on ep0out len=0/0
    usb 1-4: khubd timed out on ep0out len=0/0
    usb 1-4: device not accepting address 6, error -110
    ehci_hcd 0000:00:10.4: port 4 high speed
    ehci_hcd 0000:00:10.4: GetStatus port 4 status 001005 POWER sig=se0 PE 
CONNECT
    usb 1-4: new high speed USB device using ehci_hcd and address 7
    usb 1-4: khubd timed out on ep0in len=18/64
    ehci_hcd 0000:00:10.4: port 4 high speed
    ehci_hcd 0000:00:10.4: GetStatus port 4 status 001005 POWER sig=se0 PE 
CONNECT
    usb 1-4: khubd timed out on ep0out len=0/0
    usb 1-4: khubd timed out on ep0out len=0/0
    usb 1-4: device not accepting address 7, error -110
    ehci_hcd 0000:00:10.4: port 4 high speed
    ehci_hcd 0000:00:10.4: GetStatus port 4 status 001005 POWER sig=se0 PE 
CONNECT
    usb 1-4: new high speed USB device using ehci_hcd and address 8
    usb 1-4: khubd timed out on ep0out len=0/0
    usb 1-4: khubd timed out on ep0out len=0/0
    usb 1-4: device not accepting address 8, error -110
    ehci_hcd 0000:00:10.4: port 4 high speed
    ehci_hcd 0000:00:10.4: GetStatus port 4 status 001005 POWER sig=se0 PE 
CONNECT
    usb 1-4: new high speed USB device using ehci_hcd and address 9
    usb 1-4: khubd timed out on ep0out len=0/0
    usb 1-4: khubd timed out on ep0out len=0/0
    usb 1-4: device not accepting address 9, error -110
      

Any help gratefully received

jch

-------------------------------------------------------------------------
Using Tomcat but need to do more? Need to support web services, security?
Get stuff done quickly with pre-integrated technology to make your job easier
Download IBM WebSphere Application Server v.1.0.1 based on Apache Geronimo
http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642
_______________________________________________
Linux-usb-users@lists.sourceforge.net
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-users

Reply via email to