On Wednesday, 31 May 2000, at 16:47:13 (-0700), Matthew Dharm wrote:
> Well, these logs look good so far. Did you try to access the device? Try
> mounting sdb or sdb[1-4].
tried sdb:
/dev/sdb: Input/output error
mount: block device /dev/sdb is write-protected, mounting read-only
/dev/sdb: Input/output error
mount: you must specify the filesystem type
tried sdb[1-4]:
mount: block device /dev/sdb1 is write-protected, mounting read-only
mount: /dev/sdb1 is not a valid block device
i added:
{ 0x54c, 0x10, 0x210,
"Sony DSC-S30", US_SC_RBC, US_PR_CB, US_FL_SINGLE_LUN},
to the top of us_unusual_dev_list[]
also, i'm wondering why i dont have the usb device list and such in /proc/usb,
do i need to mount some /dev/ -t usbdevfs to /proc/usb? and /proc/bus/usb doesnt
contain anything either.
Evan Webb
[EMAIL PROTECTED]
>
> Also, could you send the exact lines you used in the unusual device list?
>
> Matt Dharm
>
> On Wed, May 31, 2000 at 03:34:01PM -0700, Evan Webb wrote:
> > I've just got myself a Sony DSC-S30 and i'm looking to get it working under
> > linux. I've seen the F505 stuff, so i thought that it probably was the same, but
> > the usb-storage driver does not recognize it by default. I tried adding it's id
> > #'s to the unusual_device list, and then the the driver recognized it. I've
> > enclose the logs of what dmesg says on each try.
> >
> > oh, this is the 2.4.0-test1 usb stack.
> >
> > Basic usb-storage w/o my id's patched in:
> >
> > usb.c: registered new driver usb-storage
> > USB Mass Storage support registered.
> > uhci.c: root-hub INT complete: port1: 93 port2: 1a5 data: 2
> > hub.c: port 1 connection change
> > hub.c: portstatus 101, change 1, 12 Mb/s
> > hub.c: portstatus 103, change 0, 12 Mb/s
> > usb.c: USB new device connect, assigned device number 3
> > usb.c: kmalloc IF c4f87f40, numif 1
> > usb.c: new device strings: Mfr=1, Product=2, SerialNumber=0
> > usb.c: USB device number 3 default language ID 0x409
> > Manufacturer: Sony
> > Product: Sony DSC
> > usb-storage.c: Searching unusual device list for (0x54c, 0x10, 0x210)...
> > usb-storage.c: -- did not find a matching device
> > usb.c: unhandled interfaces on device
> > usb.c: This device is not recognized by any installed USB driver.
> > Length = 18
> > DescriptorType = 01
> > USB version = 1.00
> > Vendor:Product = 054c:0010
> > MaxPacketSize0 = 8
> > NumConfigurations = 1
> > Device version = 2.10
> > Device Class:SubClass:Protocol = 00:00:00
> > Per-interface classes
> > Configuration:
> > bLength = 9
> > bDescriptorType = 02
> > wTotalLength = 0027
> > bNumInterfaces = 01
> > bConfigurationValue = 01
> > iConfiguration = 00
> > bmAttributes = 40
> > MaxPower = 2mA
> >
> > Interface: 0
> > Alternate Setting: 0
> > bLength = 9
> > bDescriptorType = 04
> > bInterfaceNumber = 00
> > bAlternateSetting = 00
> > bNumEndpoints = 03
> > bInterface Class:SubClass:Protocol = 08:ff:01
> > iInterface = 00
> > Endpoint:
> > bLength = 7
> > bDescriptorType = 05
> > bEndpointAddress = 01 (out)
> > bmAttributes = 02 (Bulk)
> > wMaxPacketSize = 0040
> > bInterval = 00
> > Endpoint:
> > bLength = 7
> > bDescriptorType = 05
> > bEndpointAddress = 82 (in)
> > bmAttributes = 02 (Bulk)
> > wMaxPacketSize = 0040
> > bInterval = 00
> > Endpoint:
> > bLength = 7
> > bDescriptorType = 05
> > bEndpointAddress = 83 (in)
> > bmAttributes = 03 (Interrupt)
> > wMaxPacketSize = 0008
> > bInterval = ff
> >
> > Now with my id patchs:
> >
> > usb.c: registered new driver usb-storage
> > USB Mass Storage support registered.
> > uhci.c: root-hub INT complete: port1: 93 port2: 1a5 data: 2
> > hub.c: port 1 connection change
> > hub.c: portstatus 101, change 1, 12 Mb/s
> > hub.c: portstatus 103, change 0, 12 Mb/s
> > usb.c: USB new device connect, assigned device number 3
> > usb.c: kmalloc IF c3e52220, numif 1
> > usb.c: new device strings: Mfr=1, Product=2, SerialNumber=0
> > usb.c: USB device number 3 default language ID 0x409
> > Manufacturer: Sony
> > Product: Sony DSC
> > usb-storage.c: Searching unusual device list for (0x54c, 0x10, 0x210)...
> > usb-storage.c: -- found matching device: Sony DSC-S30
> > usb-storage.c: USB Mass Storage device detected
> > usb-storage.c: Endpoints: In: 0xcd6d8f31 Out: 0xcd6d8f20 Int: 0xcd6d8f42 (Period
> > 255)
> > usb-storage.c: Result from usb_set_interface is 0
> > usb-storage.c: New GUID 054c00100000000000000000
> > usb-storage.c: Transport: Control/Bulk
> > usb-storage.c: Protocol: Reduced Block Commands (RBC)
> > usb-storage.c: *** thread sleeping.
> > scsi1 : SCSI emulation for USB Mass Storage devices
> > scsi : 2 hosts.
> > usb-storage.c: us_queuecommand() called
> > usb-storage.c: *** thread awakened.
> > usb-storage.c: Command TEST_UNIT_READY (6 bytes)
> > usb-storage.c: 00 00 00 00 00 00 00 00 e0 45
> > usb-storage.c: Call to usb_stor_control_msg() returned 6
> > usb-storage.c: -- CB transport device requiring auto-sense
> > usb-storage.c: Issuing auto-REQUEST_SENSE
> > usb-storage.c: Call to usb_stor_control_msg() returned 6
> > usb-storage.c: us_transfer_partial(): xfer 18 bytes
> > usb-storage.c: usb_stor_bulk_msg() returned 0 xferred 18/18
> > usb-storage.c: us_transfer_partial(): transfer complete
> > usb-storage.c: CB data stage result is 0x0
> > usb-storage.c: -- Result from auto-sense is 0
> > usb-storage.c: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
> > usb-storage.c: scsi cmd done, result=0x0
> > usb-storage.c: *** thread sleeping.
> > usb-storage.c: us_queuecommand() called
> > usb-storage.c: *** thread awakened.
> > usb-storage.c: Command INQUIRY (6 bytes)
> > usb-storage.c: 12 00 00 00 ff 00 00 00 e0 45
> > usb-storage.c: Call to usb_stor_control_msg() returned 6
> > usb-storage.c: us_transfer_partial(): xfer 256 bytes
> > usb-storage.c: usb_stor_bulk_msg() returned 0 xferred 72/256
> > usb-storage.c: CB data stage result is 0x1
> > usb-storage.c: -- CB transport device requiring auto-sense
> > usb-storage.c: Issuing auto-REQUEST_SENSE
> > usb-storage.c: Call to usb_stor_control_msg() returned 6
> > usb-storage.c: us_transfer_partial(): xfer 18 bytes
> > usb-storage.c: usb_stor_bulk_msg() returned 0 xferred 18/18
> > usb-storage.c: us_transfer_partial(): transfer complete
> > usb-storage.c: CB data stage result is 0x0
> > usb-storage.c: -- Result from auto-sense is 0
> > usb-storage.c: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
> > usb-storage.c: Fixing INQUIRY data, setting SCSI rev to 2
> > usb-storage.c: scsi cmd done, result=0x0
> > usb-storage.c: *** thread sleeping.
> > Vendor: Sony Model: Sony DSC Rev: 2.10
> > Type: Direct-Access ANSI SCSI revision: 02
> > Detected scsi removable disk sdb at scsi1, channel 0, id 0, lun 0
> > usb-storage.c: us_queuecommand() called
> > usb-storage.c: *** thread awakened.
> > usb-storage.c: Bad device number (1/0)
> > usb-storage.c: *** thread sleeping.
> > usb-storage.c: us_queuecommand() called
> > usb-storage.c: *** thread awakened.
> > usb-storage.c: Bad device number (2/0)
> > usb-storage.c: *** thread sleeping.
> > usb-storage.c: us_queuecommand() called
> > usb-storage.c: *** thread awakened.
> > usb-storage.c: Bad device number (3/0)
> > usb-storage.c: *** thread sleeping.
> > usb-storage.c: us_queuecommand() called
> > usb-storage.c: *** thread awakened.
> > usb-storage.c: Bad device number (4/0)
> > usb-storage.c: *** thread sleeping.
> > usb-storage.c: us_queuecommand() called
> > usb-storage.c: *** thread awakened.
> > usb-storage.c: Bad device number (5/0)
> > usb-storage.c: *** thread sleeping.
> > usb-storage.c: us_queuecommand() called
> > usb-storage.c: *** thread awakened.
> > usb-storage.c: Bad device number (6/0)
> > usb-storage.c: *** thread sleeping.
> > usb-storage.c: us_queuecommand() called
> > usb-storage.c: *** thread awakened.
> > usb-storage.c: Bad device number (7/0)
> > usb-storage.c: *** thread sleeping.
> > usb-storage.c: us_queuecommand() called
> > usb-storage.c: *** thread awakened.
> > usb-storage.c: Command TEST_UNIT_READY (6 bytes)
> > usb-storage.c: 00 00 00 00 00 00 00 00 00 00
> > usb-storage.c: Call to usb_stor_control_msg() returned 6
> > usb-storage.c: -- CB transport device requiring auto-sense
> > usb-storage.c: Issuing auto-REQUEST_SENSE
> > usb-storage.c: Call to usb_stor_control_msg() returned 6
> > usb-storage.c: us_transfer_partial(): xfer 18 bytes
> > usb-storage.c: usb_stor_bulk_msg() returned 0 xferred 18/18
> > usb-storage.c: us_transfer_partial(): transfer complete
> > usb-storage.c: CB data stage result is 0x0
> > usb-storage.c: -- Result from auto-sense is 0
> > usb-storage.c: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
> > usb-storage.c: scsi cmd done, result=0x0
> > usb-storage.c: *** thread sleeping.
> > usb-storage.c: us_queuecommand() called
> > usb-storage.c: *** thread awakened.
> > usb-storage.c: Command READ_CAPACITY (10 bytes)
> > usb-storage.c: 25 00 00 00 00 00 00 00 00 00
> > usb-storage.c: Call to usb_stor_control_msg() returned 10
> > usb-storage.c: us_transfer_partial(): xfer 8 bytes
> > usb-storage.c: usb_stor_bulk_msg() returned 0 xferred 8/8
> > usb-storage.c: us_transfer_partial(): transfer complete
> > usb-storage.c: CB data stage result is 0x0
> > usb-storage.c: -- CB transport device requiring auto-sense
> > usb-storage.c: Issuing auto-REQUEST_SENSE
> > usb-storage.c: Call to usb_stor_control_msg() returned 10
> > usb-storage.c: us_transfer_partial(): xfer 18 bytes
> > usb-storage.c: usb_stor_bulk_msg() returned 0 xferred 18/18
> > usb-storage.c: us_transfer_partial(): transfer complete
> > usb-storage.c: CB data stage result is 0x0
> > usb-storage.c: -- Result from auto-sense is 0
> > usb-storage.c: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
> > usb-storage.c: scsi cmd done, result=0x0
> > usb-storage.c: *** thread sleeping.
> > SCSI device sdb: hdwr sector= 512 bytes. Sectors= 7904 [3 MB] [0.0 GB]
> > usb-storage.c: us_queuecommand() called
> > usb-storage.c: *** thread awakened.
> > usb-storage.c: Command MODE_SENSE (6 bytes)
> > usb-storage.c: 1a 00 01 00 0c 00 00 00 00 00
> > usb-storage.c: Call to usb_stor_control_msg() returned -32
> > usb-storage.c: -- Stall on control pipe. Clearing
> > usb-storage.c: -- usb_clear_halt() returns 0
> > usb-storage.c: -- CB transport device requiring auto-sense
> > usb-storage.c: -- transport indicates command failure
> > usb-storage.c: Issuing auto-REQUEST_SENSE
> > usb-storage.c: Call to usb_stor_control_msg() returned 6
> > usb-storage.c: us_transfer_partial(): xfer 18 bytes
> > usb-storage.c: usb_stor_bulk_msg() returned 0 xferred 18/18
> > usb-storage.c: us_transfer_partial(): transfer complete
> > usb-storage.c: CB data stage result is 0x0
> > usb-storage.c: -- Result from auto-sense is 0
> > usb-storage.c: -- code: 0x70, key: 0x5, ASC: 0x24, ASCQ: 0x0
> > usb-storage.c: scsi cmd done, result=0x1
> > usb-storage.c: *** thread sleeping.
> > sdb: test WP failed, assume Write Protected
> > sdb:<7>usb-storage.c: us_queuecommand() called
> > usb-storage.c: *** thread awakened.
> > usb-storage.c: Command READ_10 (10 bytes)
> > usb-storage.c: 28 00 00 00 00 00 00 00 02 00
> > usb-storage.c: Call to usb_stor_control_msg() returned 10
> > usb-storage.c: us_transfer_partial(): xfer 1024 bytes
> > usb-storage.c: usb_stor_bulk_msg() returned 0 xferred 1024/1024
> > usb-storage.c: us_transfer_partial(): transfer complete
> > usb-storage.c: CB data stage result is 0x0
> > usb-storage.c: -- CB transport device requiring auto-sense
> > usb-storage.c: Issuing auto-REQUEST_SENSE
> > usb-storage.c: Call to usb_stor_control_msg() returned 10
> > usb-storage.c: us_transfer_partial(): xfer 18 bytes
> > usb-storage.c: usb_stor_bulk_msg() returned 0 xferred 18/18
> > usb-storage.c: us_transfer_partial(): transfer complete
> > usb-storage.c: CB data stage result is 0x0
> > usb-storage.c: -- Result from auto-sense is 0
> > usb-storage.c: -- code: 0x70, key: 0x0, ASC: 0x0, ASCQ: 0x0
> > usb-storage.c: scsi cmd done, result=0x0
> > usb-storage.c: *** thread sleeping.
> > sdb1
> > WARNING: USB Mass Storage data integrity not assured
> > USB Mass Storage device found at 3
> > usb.c: usb-storage driver claimed interface c3e52220
> >
> >
> > Sorry for all the logs. thanks for any help.
> >
> > Evan Webb
> > [EMAIL PROTECTED]
> >
> > ---------------------------------------------------------------------
> > To unsubscribe, e-mail: [EMAIL PROTECTED]
> > For additional commands, e-mail: [EMAIL PROTECTED]
>
> --
> Matthew Dharm Home: [EMAIL PROTECTED]
> Senior Engineer, QCP Inc. Work: [EMAIL PROTECTED]
>
> G: Money isn't everything, A.J.
> AJ: Who convinced you of that?
> G: The Chief, at my last salary review.
> -- Mike and Greg
> User Friendly, 11/3/1998
>
> ---------------------------------------------------------------------
> To unsubscribe, e-mail: [EMAIL PROTECTED]
> For additional commands, e-mail: [EMAIL PROTECTED]
---------------------------------------------------------------------
To unsubscribe, e-mail: [EMAIL PROTECTED]
For additional commands, e-mail: [EMAIL PROTECTED]
