----- Forwarded message from "Dunlap, Randy" <[EMAIL PROTECTED]> -----
Envelope-to: [EMAIL PROTECTED]
Delivery-date: Mon, 12 Jun 2000 17:56:32 +0200
From: "Dunlap, Randy" <[EMAIL PROTECTED]>
To: "'[EMAIL PROTECTED]'" <[EMAIL PROTECTED]>,
[EMAIL PROTECTED]
Subject: RE: ide broken since 2.3.99-pre9 ?
Date: Mon, 12 Jun 2000 08:50:00 -0700
X-Mailer: Internet Mail Service (5.5.2448.0)
Hi,
> I own a Iwill XA100+ board with a ALI M1541 chipset and a
> 20Go UDMA66 IBM harddisk.
(stuff skipped)
> * i have a new usb trackball, but ti am not able to load
> the usb-ohci
> module, because it don't find an irq for usb (irq 5 under
> windows, the
> module reports irq 0 and suggest using pci=biosirq, which
> don't help.
For USB IRQ assignment problem, please send output of
'lspci -vv' to [EMAIL PROTECTED] and to [EMAIL PROTECTED] .
~Randy
----- End forwarded message -----
Ok, here is the lspci -vv output ...
00:00.0 Host bridge: Acer Laboratories Inc. [ALi] M1541 (rev 04)
Subsystem: Acer Laboratories Inc. [ALi]: Unknown device 1541
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Latency: 32 set
Region 0: Memory at d8000000 (32-bit, non-prefetchable) [size=64M]
Capabilities: [b0] AGP version 1.0
Status: RQ=27 SBA+ 64bit- FW- Rate=21
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=
00:01.0 PCI bridge: Acer Laboratories Inc. [ALi] M5243 (rev 04) (prog-if 00 [Normal
decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 32 set
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
Memory behind bridge: b8000000-d7ffffff
BridgeCtl: Parity- SERR+ NoISA+ VGA+ MAbort- >Reset- FastB2B-
00:02.0 USB Controller: Acer Laboratories Inc. [ALi] M5237 USB (rev 03) (prog-if 10
[OHCI])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 80 max, 32 set, cache line size 08
Interrupt: pin A routed to IRQ 0
Region 0: Memory at dc000000 (32-bit, non-prefetchable) [size=4K]
>>> this is the USB controller, and as you see it is assigned IRQ 0 ...
00:07.0 ISA bridge: Acer Laboratories Inc. [ALi] M1533 PCI to ISA Bridge [Aladdin IV]
(rev c3)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort+
<MAbort+ >SERR- <PERR-
Latency: 0 set
00:0f.0 IDE interface: Acer Laboratories Inc. [ALi] M5229 IDE (rev c1) (prog-if fa)
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 2 min, 4 max, 32 set
Interrupt: pin A routed to IRQ 0
Region 4: I/O ports at f000 [size=16]
00:12.0 SCSI storage controller: Symbios Logic Inc. (formerly NCR) 53c810 (rev 23)
Subsystem: Symbios Logic Inc. (formerly NCR) 8100S
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 8 min, 64 max, 32 set, cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at e000 [size=256]
Region 1: Memory at dc001000 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 1
Flags: PMEClk- AuxPwr- DSI- D1- D2- PME-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 Co-processor: 3DLabs: Unknown device 0008 (rev 01)
Subsystem: Appian Technology: Unknown device 3d32
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 192 min, 192 max, 32 set
Interrupt: pin A routed to IRQ 11
Region 0: Memory at ca020000 (32-bit, non-prefetchable) [size=128K]
Capabilities: [40] AGP version 1.0
Status: RQ=31 SBA+ 64bit- FW- Rate=1
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=
01:00.1 VGA compatible controller: 3DLabs: Unknown device 000a (rev 01) (prog-if 00
[VGA])
Subsystem: Appian Technology: Unknown device 3d32
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 192 min, 192 max, 32 set
Interrupt: pin A routed to IRQ 11
Region 0: Memory at ca000000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at b8000000 (32-bit, non-prefetchable) [size=64M]
Region 2: Memory at bc000000 (32-bit, non-prefetchable) [size=64M]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [4c] Power Management version 1
Flags: PMEClk- AuxPwr- DSI+ D1+ D2- PME-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.2 Display controller: 3DLabs: Unknown device 000a (rev 01)
Subsystem: Appian Technology: Unknown device 3d32
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 192 min, 192 max, 32 set
Interrupt: pin A routed to IRQ 11
Region 0: Memory at ca040000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at c0000000 (32-bit, non-prefetchable) [size=64M]
Region 2: Memory at c4000000 (32-bit, non-prefetchable) [size=64M]
Expansion ROM at c9000000 [disabled] [size=64K]
Capabilities: [4c] Power Management version 1
Flags: PMEClk- AuxPwr- DSI+ D1+ D2- PME-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Friendly,
Sven LUTHER
---------------------------------------------------------------------
To unsubscribe, e-mail: [EMAIL PROTECTED]
For additional commands, e-mail: [EMAIL PROTECTED]
