On Mon, Nov 05, 2012 at 09:43:32AM +0900, Kuninori Morimoto wrote: > Current rcar-phy driver used iowerite32/ioread32, > but it cause compile error on some architectures. > This patch used writel/readl and HAS_IOMEM to solve this issue. > > drivers/usb/phy/rcar-phy.c: In function 'rcar_usb_phy_init': > drivers/usb/phy/rcar-phy.c:75:3: error: implicit declaration of function\ > 'iowrite32' [-Werror=implicit-function-declaration] > drivers/usb/phy/rcar-phy.c:83:4: error: implicit declaration of function\ > 'ioread32' [-Werror=implicit-function-declaration] > > Signed-off-by: Kuninori Morimoto <[email protected]> > --- > >> Felipe > > Sorry for late response. > Does this patch solve the issue ?
probably, I'll leave this here for a while long and if nobody complains
will apply it.
> drivers/usb/phy/Kconfig | 1 +
> drivers/usb/phy/rcar-phy.c | 26 +++++++++++++-------------
> 2 files changed, 14 insertions(+), 13 deletions(-)
>
> diff --git a/drivers/usb/phy/Kconfig b/drivers/usb/phy/Kconfig
> index 7eb73c5..39f920b 100644
> --- a/drivers/usb/phy/Kconfig
> +++ b/drivers/usb/phy/Kconfig
> @@ -36,6 +36,7 @@ config MV_U3D_PHY
> config USB_RCAR_PHY
> tristate "Renesas R-Car USB phy support"
> depends on USB || USB_GADGET
> + depends on HAS_IOMEM
> select USB_OTG_UTILS
> help
> Say Y here to add support for the Renesas R-Car USB phy driver.
> diff --git a/drivers/usb/phy/rcar-phy.c b/drivers/usb/phy/rcar-phy.c
> index 792f505..0096660c 100644
> --- a/drivers/usb/phy/rcar-phy.c
> +++ b/drivers/usb/phy/rcar-phy.c
> @@ -72,15 +72,15 @@ static int rcar_usb_phy_init(struct usb_phy *phy)
> */
>
> /* (1) USB-PHY standby release */
> - iowrite32(PHY_ENB, (reg0 + USBPCTRL1));
> + writel(PHY_ENB, (reg0 + USBPCTRL1));
>
> /* (2) start USB-PHY internal PLL */
> - iowrite32(PHY_ENB | PLL_ENB, (reg0 + USBPCTRL1));
> + writel(PHY_ENB | PLL_ENB, (reg0 + USBPCTRL1));
>
> /* (3) USB module status check */
> for (i = 0; i < 1024; i++) {
> udelay(10);
> - val = ioread32(reg0 + USBST);
> + val = readl(reg0 + USBST);
> if (val == (ST_ACT | ST_PLL))
> break;
> }
> @@ -91,10 +91,10 @@ static int rcar_usb_phy_init(struct usb_phy *phy)
> }
>
> /* (4) USB-PHY reset clear */
> - iowrite32(PHY_ENB | PLL_ENB | PHY_RST, (reg0 + USBPCTRL1));
> + writel(PHY_ENB | PLL_ENB | PHY_RST, (reg0 + USBPCTRL1));
>
> /* set platform specific port settings */
> - iowrite32(0x00000000, (reg0 + USBPCTRL0));
> + writel(0x00000000, (reg0 + USBPCTRL0));
>
> /*
> * EHCI IP internal buffer setting
> @@ -103,21 +103,21 @@ static int rcar_usb_phy_init(struct usb_phy *phy)
> * These are recommended value of a datasheet
> * see [USB :: EHCI internal buffer setting]
> */
> - iowrite32(0x00ff0040, (reg0 + EIIBC1));
> - iowrite32(0x00ff0040, (reg1 + EIIBC1));
> + writel(0x00ff0040, (reg0 + EIIBC1));
> + writel(0x00ff0040, (reg1 + EIIBC1));
>
> - iowrite32(0x00000001, (reg0 + EIIBC2));
> - iowrite32(0x00000001, (reg1 + EIIBC2));
> + writel(0x00000001, (reg0 + EIIBC2));
> + writel(0x00000001, (reg1 + EIIBC2));
>
> /*
> * Bus alignment settings
> */
>
> /* (1) EHCI bus alignment (little endian) */
> - iowrite32(0x00000000, (reg0 + USBEH0));
> + writel(0x00000000, (reg0 + USBEH0));
>
> /* (1) OHCI bus alignment (little endian) */
> - iowrite32(0x00000000, (reg0 + USBOH0));
> + writel(0x00000000, (reg0 + USBOH0));
> }
>
> phy_init_end:
> @@ -135,8 +135,8 @@ static void rcar_usb_phy_shutdown(struct usb_phy *phy)
> spin_lock_irqsave(&priv->lock, flags);
>
> if (priv->counter-- == 1) { /* last user */
> - iowrite32(0x00000000, (reg0 + USBPCTRL0));
> - iowrite32(0x00000000, (reg0 + USBPCTRL1));
> + writel(0x00000000, (reg0 + USBPCTRL0));
> + writel(0x00000000, (reg0 + USBPCTRL1));
> }
>
> spin_unlock_irqrestore(&priv->lock, flags);
> --
> 1.7.9.5
>
--
balbi
signature.asc
Description: Digital signature
