On 11/02/2018 22:15, Martin Blumenstingl wrote:
> Amlogic Meson AXG and GXL SoCs can use the dwc3-of-simple with little
> modifications. These SoCs use:
> - a gate clock for the USB components (DWC3, USB PHYs)
> - a reset line which is shared across all USB components (DWC3, USB2 and
>   USB3 PHYs, OTG detection logic inside the USB3 PHY registers)
> - a reset pulse to trigger the reset
> - depending on the SoC two or more PHYs (AXG: 1x USB2 and 1x USB3 PHY,
>   GXL: 2x USB2 and 1x USB3 PHY)
> This extends the dwc3-of-simple so it supports (depending on the
> platform) shared and level resets. Additionally it adds new bindings
> for the Amlogic Meson AXG and GXL SoCs, along with the documentation
> (dt-bindings).
> NOTE: for full support on Amlogic Meson GXL SoCs my other series called
> "initialize (multiple) PHYs for a HCD" (see [0] for v8 of that series)
> is required. However, there is no direct dependency on that series.
> Especially since Meson AXG doesn't need it (since it only has one USB2
> and one USB3 PHY, which is already supported by the current dwc3 driver,
> unlike the 2x USB2 and 1x USB3 PHYs on Meson GXL).
> So I believe that this series can still be merged, even if the other
> patchset is not ready yet.
> changes since v1 at [1]:
> - use of_device_is_compatible() instead of struct dwc3_of_simple_params
>   as requested by Felipe Balbi (affects PATCH #2 and #3)
> - added Rob's Acked-by to the dt-bindings patch
> - added Yixun Lan's Tested-by to the whole series as he tested this
>   successfully (along with other patches) on the Amlogic Meson AXG SoC
> [0] 
> http://lists.infradead.org/pipermail/linux-amlogic/2018-January/006274.html
> [1] 
> http://lists.infradead.org/pipermail/linux-amlogic/2018-January/006286.html
> Martin Blumenstingl (3):
>   dt-bindings: usb: add support for dwc3 controller on Amlogic Meson GX
>   usb: dwc3: of-simple: add support for shared and pulsed reset lines
>   usb: dwc3: of-simple: add support for the Amlogic Meson GXL and AXG
>     SoCs
>  .../devicetree/bindings/usb/amlogic,dwc3.txt       | 42 
> ++++++++++++++++++++++
>  drivers/usb/dwc3/dwc3-of-simple.c                  | 31 ++++++++++++----
>  2 files changed, 67 insertions(+), 6 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/usb/amlogic,dwc3.txt

Hi Martin,

Successfully tested on Amlogic Q200 Reference Design board with a Meson GXM 
S912 SoC.

Other patchsets included :
- improvements and fixes for the phy-meson-gxl-usb2 driver 
- initialize (multiple) PHYs for a HCD V11 
- Meson GXL USB3 PHY driver V4 

Tested-by: Neil Armstrong <narmstr...@baylibre.con>

To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majord...@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Reply via email to