On Tue, Aug 27, 2019 at 03:39:18PM +0200, Hans de Goede wrote:
> Hi,
>
> On 26-08-19 16:32, Heikki Krogerus wrote:
> > From: Saranya Gopal <saranya.go...@intel.com>
> >
> > Enable static DRD mode in Intel platforms which guarantees
> > successful role switch all the time. This fixes issues like
> > software role switch failure after cold boot and issue with
> > role switch when USB 3.0 cable is used. But, do not enable
> > static DRD mode for Cherrytrail devices which rely on firmware
> > for role switch.
> >
> > Signed-off-by: Saranya Gopal <saranya.go...@intel.com>
> > Signed-off-by: Balaji Manoharan <m.bal...@intel.com>
> > Signed-off-by: Heikki Krogerus <heikki.kroge...@linux.intel.com>
> > ---
> > .../usb/roles/intel-xhci-usb-role-switch.c | 26 ++++++++++++++++++-
> > 1 file changed, 25 insertions(+), 1 deletion(-)
> >
> > diff --git a/drivers/usb/roles/intel-xhci-usb-role-switch.c
> > b/drivers/usb/roles/intel-xhci-usb-role-switch.c
> > index 7325a84dd1c8..9101ff94c8d2 100644
> > --- a/drivers/usb/roles/intel-xhci-usb-role-switch.c
> > +++ b/drivers/usb/roles/intel-xhci-usb-role-switch.c
> > @@ -19,6 +19,7 @@
> > #include <linux/module.h>
> > #include <linux/platform_device.h>
> > #include <linux/pm_runtime.h>
> > +#include <linux/property.h>
> > #include <linux/usb/role.h>
> > /* register definition */
> > @@ -26,6 +27,9 @@
> > #define SW_VBUS_VALID BIT(24)
> > #define SW_IDPIN_EN BIT(21)
> > #define SW_IDPIN BIT(20)
> > +#define SW_SWITCH_EN_CFG0 BIT(16)
>
> Nitpick: Please drop the _CFG0 postfix, if anything this
> should be a prefix applied to *all* defines for the bits
> in this register
>
> > +#define SW_DRD_STATIC_HOST_CFG0 1
> > +#define SW_DRD_STATIC_DEV_CFG0 2
>
> So bits 0-1 together define the drd-mode. The datasheet
> calls the combination DRD_CONFIG, without a SW_ prefix,
> with the following values being defined:
>
> 00: Dynamic role-switch
> 01: Static Host mode
> 10: Static device mode
> 11: Reserved
>
> Notice this is an enum, so the use of bit-ops to clear the
> other state below is wrong. It happens to work, but this is
> not how a multi-bit setting should be modified.
>
> I suggest using the following defines instead:
>
> #define DRD_CONFIG_DYNAMIC 0
> #define DRD_CONFIG_STATIC_HOST 1
> #define DRD_CONFIG_STATIC_DEVICE 2
> #define DRD_CONFIG_MASK 3
>
> > #define DUAL_ROLE_CFG1 0x6c
> > #define HOST_MODE BIT(29)
> > @@ -37,6 +41,7 @@
> > struct intel_xhci_usb_data {
> > struct usb_role_switch *role_sw;
> > void __iomem *base;
> > + bool disable_sw_switch;
>
> I would prefer for this to be enable_sw_switch and the negation
> when reading the property.
>
> > };
> > static const struct software_node intel_xhci_usb_node = {
> > @@ -63,23 +68,39 @@ static int intel_xhci_usb_set_role(struct device *dev,
> > enum usb_role role)
> > pm_runtime_get_sync(dev);
> > - /* Set idpin value as requested */
> > + /*
> > + * Set idpin value as requested.
> > + * Since some devices rely on firmware setting DRD_CONFIG and
> > + * SW_SWITCH_EN_CFG0 bits to be zero for role switch,
> > + * do not set these bits for those devices.
> > + */
> > val = readl(data->base + DUAL_ROLE_CFG0);
> > switch (role) {
> > case USB_ROLE_NONE:
> > val |= SW_IDPIN;
> > val &= ~SW_VBUS_VALID;
> > + val &= ~(SW_DRD_STATIC_DEV_CFG0 | SW_DRD_STATIC_HOST_CFG0);
> > break;
>
> Right, so this should be:
>
> val &= ~DRD_CONFIG_MASK;
>
> Also ideally this should also have a if (!data->disable_sw_switch)
> for consistency.
>
> > case USB_ROLE_HOST:
> > val &= ~SW_IDPIN;
> > val &= ~SW_VBUS_VALID;
> > + if (!data->disable_sw_switch) {
> > + val &= ~SW_DRD_STATIC_DEV_CFG0;
>
> So this clearing is wrong, it happens to work, but is not
> how modifying a "bit-set" / enum should be done, this should be:
>
> val &= ~DRD_CONFIG_MASK;
>
> > + val |= SW_DRD_STATIC_HOST_CFG0;
> > + }
> > break;
> > case USB_ROLE_DEVICE:
> > val |= SW_IDPIN;
> > val |= SW_VBUS_VALID;
> > + if (!data->disable_sw_switch) {
> > + val &= ~SW_DRD_STATIC_HOST_CFG0;
> > + val |= SW_DRD_STATIC_DEV_CFG0;
> > + }
>
> Idem.
>
>
> > break;
> > }
> > val |= SW_IDPIN_EN;
> > + if (!data->disable_sw_switch)
> > + val |= SW_SWITCH_EN_CFG0;
>
> So we now have a lot of "if (!data->disable_sw_switch)" checks,
>
> IMHO it would be better / cleaner to do this:
>
> u32 glk, val, drd_config;
>
> ...
>
> val = readl(data->base + DUAL_ROLE_CFG0);
> switch (role) {
> case USB_ROLE_NONE:
> val |= SW_IDPIN;
> val &= ~SW_VBUS_VALID;
> drd_config = DRD_CONFIG_DYNAMIC;
> break;
> case USB_ROLE_HOST:
> val &= ~SW_IDPIN;
> val &= ~SW_VBUS_VALID;
> drd_config = DRD_CONFIG_STATIC_HOST;
> break;
> case USB_ROLE_DEVICE:
> val |= SW_IDPIN;
> val |= SW_VBUS_VALID;
> drd_config = DRD_CONFIG_STATIC_DEVICE;
> break;
> }
> val |= SW_IDPIN_EN;
>
> if (!data->disable_sw_switch) {
> val &= ~DRD_CONFIG_MASK;
> val |= SW_SWITCH_EN_CFG0 | drd_config;
> }
That looks good to me. Saranya, Balaji! Can you fix that. I don't
think you need me for this anymore.
thanks,
--
heikki
