Add platform device for 'nop-usb-xceiv'. This will be used as a PHY for HS USB Port 2, so provide binding information for it.
Use usbhs_init_phys() to register the PHY's RESET regulator. VAUX2 supplies the PHY's VCC. Signed-off-by: Roger Quadros <[email protected]> --- arch/arm/mach-omap2/board-omap3evm.c | 41 ++++++++++++++++++++++++---------- 1 files changed, 29 insertions(+), 12 deletions(-) diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c index 48789e0..aaa01ae 100644 --- a/arch/arm/mach-omap2/board-omap3evm.c +++ b/arch/arm/mach-omap2/board-omap3evm.c @@ -34,6 +34,7 @@ #include <linux/usb/otg.h> #include <linux/usb/musb.h> #include <linux/usb/nop-usb-xceiv.h> +#include <linux/usb/phy.h> #include <linux/smsc911x.h> #include <linux/wl12xx.h> @@ -496,7 +497,7 @@ struct wl12xx_platform_data omap3evm_wlan_data __initdata = { static struct regulator_consumer_supply omap3evm_vaux2_supplies[] = { REGULATOR_SUPPLY("VDD_CSIPHY1", "omap3isp"), /* OMAP ISP */ REGULATOR_SUPPLY("VDD_CSIPHY2", "omap3isp"), /* OMAP ISP */ - REGULATOR_SUPPLY("hsusb1", "ehci-omap.0"), + REGULATOR_SUPPLY("vcc", "nop_usb_xceiv.2"), /* hsusb port 2 */ REGULATOR_SUPPLY("vaux2", NULL), }; @@ -539,17 +540,27 @@ static int __init omap3_evm_i2c_init(void) return 0; } -static struct usbhs_omap_platform_data usbhs_bdata __initdata = { +/* PHY device on HS USB Port 2 i.e. nop_usb_xceiv.2 */ +static struct platform_device hsusb2_phy_device = { + .name = "nop_usb_xceiv", + .id = 2, +}; - .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED, - .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY, - .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED, +static struct usbhs_phy_data phy_data[] __initdata = { + { + .port = 2, + .reset_gpio = -1, /* set at runtime */ + .vcc_gpio = -EINVAL, + .phy_id = "nop_usb_xceiv.2", + }, +}; - .phy_reset = true, - /* PHY reset GPIO will be runtime programmed based on EVM version */ - .reset_gpio_port[0] = -EINVAL, - .reset_gpio_port[1] = -EINVAL, - .reset_gpio_port[2] = -EINVAL +static struct platform_device *omap3evm_devices[] __initdata = { + &hsusb2_phy_device, +}; + +static struct usbhs_omap_platform_data usbhs_bdata __initdata = { + .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY, }; #ifdef CONFIG_OMAP_MUX @@ -725,7 +736,7 @@ static void __init omap3_evm_init(void) /* setup EHCI phy reset config */ omap_mux_init_gpio(21, OMAP_PIN_INPUT_PULLUP); - usbhs_bdata.reset_gpio_port[1] = 21; + phy_data[0].reset_gpio = 21; /* EVM REV >= E can supply 500mA with EXTVBUS programming */ musb_board_data.power = 500; @@ -733,10 +744,16 @@ static void __init omap3_evm_init(void) } else { /* setup EHCI phy reset on MDC */ omap_mux_init_gpio(135, OMAP_PIN_OUTPUT); - usbhs_bdata.reset_gpio_port[1] = 135; + phy_data[0].reset_gpio = 135; } usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb"); usb_musb_init(&musb_board_data); + + platform_add_devices(omap3evm_devices, ARRAY_SIZE(omap3evm_devices)); + /* PHY on HSUSB Port 2 i.e. index 1 */ + usb_bind_phy("ehci-omap.0", 1, "nop_usb_xceiv.2"); + + usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data)); usbhs_init(&usbhs_bdata); board_nand_init(omap3evm_nand_partitions, ARRAY_SIZE(omap3evm_nand_partitions), NAND_CS, -- 1.7.4.1 -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
