The SATA adapter has a power input, but it is not used, it is connected to the
PC with Y-type USB cable.
The disk works with my "smart" TV, it works with Windows on the same machine,
it also had worked some time ago with Linux, but now it shows the following:
[ 2192.027213] usb 1-3: new high-speed USB device number 5 using xhci_hcd
[ 2192.042323] ums-cypress 1-3:1.0: USB Mass Storage device detected
[ 2192.042500] scsi9 : usb-storage 1-3:1.0
[ 2193.044219] scsi 9:0:0:0: Direct-Access WDC WD64 00BPVT-00HXZT0
PQ: 0 ANSI: 0
[ 2193.045083] sd 9:0:0:0: [sdb] 1250263728 512-byte logical blocks: (640
GB/596 GiB)
[ 2193.045240] sd 9:0:0:0: [sdb] Write Protect is off
[ 2193.045245] sd 9:0:0:0: [sdb] Mode Sense: 03 00 00 00
[ 2193.045384] sd 9:0:0:0: [sdb] No Caching mode page found
[ 2193.045388] sd 9:0:0:0: [sdb] Assuming drive cache: write through
[ 2193.046259] sd 9:0:0:0: [sdb] No Caching mode page found
[ 2193.046264] sd 9:0:0:0: [sdb] Assuming drive cache: write through
[ 2193.054389] sdb: sdb1
[ 2193.055092] sd 9:0:0:0: [sdb] No Caching mode page found
[ 2193.055095] sd 9:0:0:0: [sdb] Assuming drive cache: write through
[ 2193.055098] sd 9:0:0:0: [sdb] Attached SCSI disk
[ 2200.821345] usb 1-3: reset high-speed USB device number 5 using xhci_hcd
[ 2200.835063] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with
disabled ep ffff8800bc71e480
[ 2200.835068] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with
disabled ep ffff8800bc71e4c0
[ 2267.897715] sd 9:0:0:0: [sdb] Unhandled sense code
[ 2267.897719] sd 9:0:0:0: [sdb]
[ 2267.897721] Result: hostbyte=0x07 driverbyte=0x08
[ 2267.897722] sd 9:0:0:0: [sdb]
[ 2267.897724] Sense Key : 0x4 [current]
[ 2267.897735] sd 9:0:0:0: [sdb]
[ 2267.897736] ASC=0x0 ASCQ=0x0
[ 2267.897738] sd 9:0:0:0: [sdb] CDB:
[ 2267.897740] cdb[0]=0x28: 28 00 4a 85 6e af 00 00 08 00
[ 2267.897746] end_request: I/O error, dev sdb, sector 1250258607
[ 2267.897750] Buffer I/O error on device sdb1, logical block 625129272
[ 2267.897752] Buffer I/O error on device sdb1, logical block 625129273
[ 2267.897753] Buffer I/O error on device sdb1, logical block 625129274
[ 2267.897754] Buffer I/O error on device sdb1, logical block 625129275
[ 2270.884154] usb 1-3: USB disconnect, device number 5
Bus 001 Device 010: ID 14cd:6116 Super Top M6116 SATA Bridge
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x14cd Super Top
idProduct 0x6116 M6116 SATA Bridge
bcdDevice 1.50
iManufacturer 1 Super Top
iProduct 3 USB 2.0 SATA BRIDGE
iSerial 2 M6116018VE15
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 32
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xc0
Self Powered
MaxPower 2mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk-Only
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0001
Self Powered
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
