Hi,
I have a problem with sdhc and sd-cards. I cannot access the cards because
I always get I/O errors according to dmesg.
I tried 2 types of card readers and 3 types of sdhc cards. I also tried the
sdhc cards with sd-card adapters.
Interesting is, that i both cases, sdhc card directly and with a sdcard
adapter, there is no accessibility. But, dmesg output with the I/O error
only comes with sdhc directly.
I also tried some usb-storage quirks. Nothing worked.
Approximately a year ago, as I can recall with kernel 3.*, the cards worked
proper.
I cannot access the cards with dd and so on. I only register, that I can
open den device with gdisk, a least it looks this way. You can even
recognice the size of the card. More Output below.
###lsusb Output:
[root@Rechner ~]# lsusb
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 004: ID 05e3:0745 Genesys Logic, Inc. Logilink CR0012
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 002: ID 046d:c52e Logitech, Inc. MK260 Wireless Combo
Receiver
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
###Detail lsusb Output:
[root@Rechner ~]# lsusb -v
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0001 1.1 root hub
bcdDevice 4.03
iManufacturer 3 Linux 4.3.3-1-ARCH ohci_hcd
iProduct 2 OHCI PCI host controller
iSerial 1 0000:00:14.5
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x0012
No power switching (usb 1.0)
No overcurrent protection
bPwrOn2PwrGood 2 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
can't get debug descriptor: Resource temporarily unavailable
Device Status: 0x0001
Self Powered
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0002 2.0 root hub
bcdDevice 4.03
iManufacturer 3 Linux 4.3.3-1-ARCH ehci_hcd
iProduct 2 EHCI Host Controller
iSerial 1 0000:00:13.2
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 6
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Port 3: 0000.0100 power
Port 4: 0000.0100 power
Port 5: 0000.0100 power
Port 6: 0000.0100 power
can't get device qualifier: Resource temporarily unavailable
can't get debug descriptor: Resource temporarily unavailable
Device Status: 0x0001
Self Powered
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0001 1.1 root hub
bcdDevice 4.03
iManufacturer 3 Linux 4.3.3-1-ARCH ohci_hcd
iProduct 2 OHCI PCI host controller
iSerial 1 0000:00:13.1
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 3
wHubCharacteristic 0x0012
No power switching (usb 1.0)
No overcurrent protection
bPwrOn2PwrGood 2 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Port 3: 0000.0100 power
can't get debug descriptor: Resource temporarily unavailable
Device Status: 0x0001
Self Powered
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0001 1.1 root hub
bcdDevice 4.03
iManufacturer 3 Linux 4.3.3-1-ARCH ohci_hcd
iProduct 2 OHCI PCI host controller
iSerial 1 0000:00:13.0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 3
wHubCharacteristic 0x0012
No power switching (usb 1.0)
No overcurrent protection
bPwrOn2PwrGood 2 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Port 3: 0000.0100 power
can't get debug descriptor: Resource temporarily unavailable
Device Status: 0x0001
Self Powered
Bus 003 Device 004: ID 05e3:0745 Genesys Logic, Inc. Logilink CR0012
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x05e3 Genesys Logic, Inc.
idProduct 0x0745 Logilink CR0012
bcdDevice 9.02
iManufacturer 0
iProduct 1 USB Storage
iSerial 2 000000000902
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 32
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk-Only
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
can't get debug descriptor: Resource temporarily unavailable
Device Status: 0x0000
(Bus Powered)
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0002 2.0 root hub
bcdDevice 4.03
iManufacturer 3 Linux 4.3.3-1-ARCH ehci_hcd
iProduct 2 EHCI Host Controller
iSerial 1 0000:00:12.2
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 6
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0503 highspeed power enable connect
Port 3: 0000.0100 power
Port 4: 0000.0100 power
Port 5: 0000.0100 power
Port 6: 0000.0100 power
can't get device qualifier: Resource temporarily unavailable
can't get debug descriptor: Resource temporarily unavailable
Device Status: 0x0001
Self Powered
Bus 002 Device 002: ID 046d:c52e Logitech, Inc. MK260 Wireless Combo
Receiver
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x046d Logitech, Inc.
idProduct 0xc52e MK260 Wireless Combo Receiver
bcdDevice 23.01
iManufacturer 1 Logitech
iProduct 2 USB Receiver
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 59
bNumInterfaces 2
bConfigurationValue 1
iConfiguration 4 RQR23.01_B0006
bmAttributes 0xa0
(Bus Powered)
Remote Wakeup
MaxPower 98mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 3 Human Interface Device
bInterfaceSubClass 1 Boot Interface Subclass
bInterfaceProtocol 1 Keyboard
iInterface 0
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.11
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 59
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 8
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 3 Human Interface Device
bInterfaceSubClass 1 Boot Interface Subclass
bInterfaceProtocol 2 Mouse
iInterface 0
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.11
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 177
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0014 1x 20 bytes
bInterval 2
can't get device qualifier: Resource temporarily unavailable
can't get debug descriptor: Resource temporarily unavailable
Device Status: 0x0000
(Bus Powered)
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0001 1.1 root hub
bcdDevice 4.03
iManufacturer 3 Linux 4.3.3-1-ARCH ohci_hcd
iProduct 2 OHCI PCI host controller
iSerial 1 0000:00:12.1
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 3
wHubCharacteristic 0x0012
No power switching (usb 1.0)
No overcurrent protection
bPwrOn2PwrGood 2 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Port 3: 0000.0103 power enable connect
can't get debug descriptor: Resource temporarily unavailable
Device Status: 0x0001
Self Powered
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0001 1.1 root hub
bcdDevice 4.03
iManufacturer 3 Linux 4.3.3-1-ARCH ohci_hcd
iProduct 2 OHCI PCI host controller
iSerial 1 0000:00:12.0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 3
wHubCharacteristic 0x0012
No power switching (usb 1.0)
No overcurrent protection
bPwrOn2PwrGood 2 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Port 3: 0000.0100 power
can't get debug descriptor: Resource temporarily unavailable
Device Status: 0x0001
Self Powered
[root@Rechner ~]#
###Dmesg after inserting the sdhc card
[ 37.700261] usb 3-2: USB disconnect, device number 2
[ 37.961023] usb 3-2: new high-speed USB device number 4 using ehci-pci
[ 38.097427] usb-storage 3-2:1.0: USB Mass Storage device detected
[ 38.098596] scsi host7: usb-storage 3-2:1.0
[ 39.099025] scsi 7:0:0:0: Direct-Access Generic STORAGE DEVICE
0902 PQ: 0 ANSI: 6
[ 39.331856] sd 7:0:0:0: [sdc] 15564800 512-byte logical blocks: (7.96
GB/7.42 GiB)
[ 39.333349] sd 7:0:0:0: [sdc] Write Protect is off
[ 39.333363] sd 7:0:0:0: [sdc] Mode Sense: 21 00 00 00
[ 39.334991] sd 7:0:0:0: [sdc] Write cache: disabled, read cache:
enabled, doesn't support DPO or FUA
[ 41.094909] sd 7:0:0:0: [sdc] UNKNOWN(0x2003) Result: hostbyte=0x00
driverbyte=0x08
[ 41.094923] sd 7:0:0:0: [sdc] Sense Key : 0xb [current]
[ 41.094931] sd 7:0:0:0: [sdc] ASC=0x47 ASCQ=0x1
[ 41.094939] sd 7:0:0:0: [sdc] CDB: opcode=0x28 28 00 00 00 00 00 00 00
08 00
[ 41.094946] blk_update_request: I/O error, dev sdc, sector 0
[ 41.094955] Buffer I/O error on dev sdc, logical block 0, async page read
[ 42.846495] sd 7:0:0:0: [sdc] UNKNOWN(0x2003) Result: hostbyte=0x00
driverbyte=0x08
[ 42.846509] sd 7:0:0:0: [sdc] Sense Key : 0xb [current]
[ 42.846517] sd 7:0:0:0: [sdc] ASC=0x47 ASCQ=0x1
[ 42.846525] sd 7:0:0:0: [sdc] CDB: opcode=0x28 28 00 00 00 00 00 00 00
08 00
[ 42.846531] blk_update_request: I/O error, dev sdc, sector 0
[ 42.846541] Buffer I/O error on dev sdc, logical block 0, async page read
[ 42.846597] ldm_validate_partition_table(): Disk read failed.
[ 44.595789] sd 7:0:0:0: [sdc] UNKNOWN(0x2003) Result: hostbyte=0x00
driverbyte=0x08
[ 44.595804] sd 7:0:0:0: [sdc] Sense Key : 0xb [current]
[ 44.595811] sd 7:0:0:0: [sdc] ASC=0x47 ASCQ=0x1
[ 44.595819] sd 7:0:0:0: [sdc] CDB: opcode=0x28 28 00 00 00 00 00 00 00
08 00
[ 44.595825] blk_update_request: I/O error, dev sdc, sector 0
[ 44.595834] Buffer I/O error on dev sdc, logical block 0, async page read
[ 46.346338] sd 7:0:0:0: [sdc] UNKNOWN(0x2003) Result: hostbyte=0x00
driverbyte=0x08
[ 46.346353] sd 7:0:0:0: [sdc] Sense Key : 0xb [current]
[ 46.346360] sd 7:0:0:0: [sdc] ASC=0x47 ASCQ=0x1
[ 46.346369] sd 7:0:0:0: [sdc] CDB: opcode=0x28 28 00 00 00 00 00 00 00
08 00
[ 46.346376] blk_update_request: I/O error, dev sdc, sector 0
[ 46.346386] Buffer I/O error on dev sdc, logical block 0, async page read
[ 48.094779] sd 7:0:0:0: [sdc] UNKNOWN(0x2003) Result: hostbyte=0x00
driverbyte=0x08
[ 48.094794] sd 7:0:0:0: [sdc] Sense Key : 0xb [current]
[ 48.094801] sd 7:0:0:0: [sdc] ASC=0x47 ASCQ=0x1
[ 48.094809] sd 7:0:0:0: [sdc] CDB: opcode=0x28 28 00 00 00 00 00 00 00
08 00
[ 48.094816] blk_update_request: I/O error, dev sdc, sector 0
[ 48.094825] Buffer I/O error on dev sdc, logical block 0, async page read
[ 48.094880] sdc: unable to read partition table
[ 48.100667] sd 7:0:0:0: [sdc] Attached SCSI removable disk
[ 49.856376] sd 7:0:0:0: [sdc] UNKNOWN(0x2003) Result: hostbyte=0x00
driverbyte=0x08
[ 49.856391] sd 7:0:0:0: [sdc] Sense Key : 0xb [current]
[ 49.856398] sd 7:0:0:0: [sdc] ASC=0x47 ASCQ=0x1
[ 49.856407] sd 7:0:0:0: [sdc] CDB: opcode=0x28 28 00 00 ed 7f 80 00 00
08 00
[ 49.856414] blk_update_request: I/O error, dev sdc, sector 15564672
[ 51.607715] sd 7:0:0:0: [sdc] UNKNOWN(0x2003) Result: hostbyte=0x00
driverbyte=0x08
[ 51.607729] sd 7:0:0:0: [sdc] Sense Key : 0xb [current]
[ 51.607737] sd 7:0:0:0: [sdc] ASC=0x47 ASCQ=0x1
[ 51.607745] sd 7:0:0:0: [sdc] CDB: opcode=0x28 28 00 00 ed 7f 80 00 00
08 00
[ 51.607752] blk_update_request: I/O error, dev sdc, sector 15564672
[ 51.607761] Buffer I/O error on dev sdc, logical block 1945584, async
page read
###I can open the card with gdisk. I looks like I can partition the sdhc.
[root@Rechner ~]# gdisk /dev/sdc
GPT fdisk (gdisk) version 1.0.1
Warning! Read error 5; strange behavior now likely!
Warning! Read error 5; strange behavior now likely!
Partition table scan:
MBR: not present
BSD: not present
APM: not present
GPT: not present
Creating new GPT entries.
Command (? for help): p
Disk /dev/sdc: 15564800 sectors, 7.4 GiB
Logical sector size: 512 bytes
Disk identifier (GUID): 9601E190-5896-4BD1-8633-DEA9EFA7E116
Partition table holds up to 128 entries
First usable sector is 34, last usable sector is 15564766
Partitions will be aligned on 2048-sector boundaries
Total free space is 15564733 sectors (7.4 GiB)
Number Start (sector) End (sector) Size Code Name
Command (? for help): n
Partition number (1-128, default 1):
First sector (34-15564766, default = 2048) or {+-}size{KMGTP}:
Last sector (2048-15564766, default = 15564766) or {+-}size{KMGTP}:
Current type is 'Linux filesystem'
Hex code or GUID (L to show codes, Enter = 8300):
Changed type of partition to 'Linux filesystem'
Command (? for help): p
Disk /dev/sdc: 15564800 sectors, 7.4 GiB
Logical sector size: 512 bytes
Disk identifier (GUID): 9601E190-5896-4BD1-8633-DEA9EFA7E116
Partition table holds up to 128 entries
First usable sector is 34, last usable sector is 15564766
Partitions will be aligned on 2048-sector boundaries
Total free space is 2014 sectors (1007.0 KiB)
Number Start (sector) End (sector) Size Code Name
1 2048 15564766 7.4 GiB 8300 Linux filesystem
Command (? for help): w
Final checks complete. About to write GPT data. THIS WILL OVERWRITE EXISTING
PARTITIONS!!
Do you want to proceed? (Y/N): y
OK; writing new GUID partition table (GPT) to /dev/sdc.
Unable to save backup partition table! Perhaps the 'e' option on the
experts'
menu will resolve this problem.
Warning! An error was reported when writing the partition table! This error
MIGHT be harmless, or the disk might be damaged! Checking it is advisable.
Command (? for help):
###After partition the disk more dmesg output:
[ 91.164748] sd 7:0:0:0: [sdc] UNKNOWN(0x2003) Result: hostbyte=0x00
driverbyte=0x08
[ 91.164762] sd 7:0:0:0: [sdc] Sense Key : 0xb [current]
[ 91.164770] sd 7:0:0:0: [sdc] ASC=0x47 ASCQ=0x1
[ 91.164778] sd 7:0:0:0: [sdc] CDB: opcode=0x28 28 00 00 00 00 00 00 00
20 00
[ 91.164784] blk_update_request: I/O error, dev sdc, sector 0
[ 92.914049] sd 7:0:0:0: [sdc] UNKNOWN(0x2003) Result: hostbyte=0x00
driverbyte=0x08
[ 92.914062] sd 7:0:0:0: [sdc] Sense Key : 0xb [current]
[ 92.914068] sd 7:0:0:0: [sdc] ASC=0x47 ASCQ=0x1
[ 92.914076] sd 7:0:0:0: [sdc] CDB: opcode=0x28 28 00 00 00 00 00 00 00
08 00
[ 92.914081] blk_update_request: I/O error, dev sdc, sector 0
[ 92.914089] Buffer I/O error on dev sdc, logical block 0, async page read
[ 94.666849] sd 7:0:0:0: [sdc] UNKNOWN(0x2003) Result: hostbyte=0x00
driverbyte=0x08
[ 94.666862] sd 7:0:0:0: [sdc] Sense Key : 0xb [current]
[ 94.666868] sd 7:0:0:0: [sdc] ASC=0x47 ASCQ=0x1
[ 94.666875] sd 7:0:0:0: [sdc] CDB: opcode=0x28 28 00 00 00 00 00 00 00
08 00
[ 94.666881] blk_update_request: I/O error, dev sdc, sector 0
[ 94.666889] Buffer I/O error on dev sdc, logical block 0, async page read
[ 96.417321] sd 7:0:0:0: [sdc] UNKNOWN(0x2003) Result: hostbyte=0x00
driverbyte=0x08
[ 96.417335] sd 7:0:0:0: [sdc] Sense Key : 0xb [current]
[ 96.417341] sd 7:0:0:0: [sdc] ASC=0x47 ASCQ=0x1
[ 96.417349] sd 7:0:0:0: [sdc] CDB: opcode=0x28 28 00 00 00 00 00 00 00
08 00
[ 96.417355] blk_update_request: I/O error, dev sdc, sector 0
[ 96.417363] Buffer I/O error on dev sdc, logical block 0, async page read
[ 98.165583] sd 7:0:0:0: [sdc] UNKNOWN(0x2003) Result: hostbyte=0x00
driverbyte=0x08
[ 98.165597] sd 7:0:0:0: [sdc] Sense Key : 0xb [current]
[ 98.165603] sd 7:0:0:0: [sdc] ASC=0x47 ASCQ=0x1
[ 98.165611] sd 7:0:0:0: [sdc] CDB: opcode=0x28 28 00 00 00 00 00 00 00
08 00
[ 98.165617] blk_update_request: I/O error, dev sdc, sector 0
[ 98.165625] Buffer I/O error on dev sdc, logical block 0, async page read
[ 99.910641] sd 7:0:0:0: [sdc] UNKNOWN(0x2003) Result: hostbyte=0x00
driverbyte=0x08
[ 99.910654] sd 7:0:0:0: [sdc] Sense Key : 0xb [current]
[ 99.910661] sd 7:0:0:0: [sdc] ASC=0x47 ASCQ=0x1
[ 99.910668] sd 7:0:0:0: [sdc] CDB: opcode=0x28 28 00 00 00 00 00 00 00
08 00
[ 99.910674] blk_update_request: I/O error, dev sdc, sector 0
[ 99.910683] Buffer I/O error on dev sdc, logical block 0, async page read
[ 101.658822] sd 7:0:0:0: [sdc] UNKNOWN(0x2003) Result: hostbyte=0x00
driverbyte=0x08
[ 101.658834] sd 7:0:0:0: [sdc] Sense Key : 0xb [current]
[ 101.658841] sd 7:0:0:0: [sdc] ASC=0x47 ASCQ=0x1
[ 101.658849] sd 7:0:0:0: [sdc] CDB: opcode=0x28 28 00 00 00 00 00 00 00
08 00
[ 101.658855] blk_update_request: I/O error, dev sdc, sector 0
[ 101.658863] Buffer I/O error on dev sdc, logical block 0, async page read
[ 103.403756] sd 7:0:0:0: [sdc] UNKNOWN(0x2003) Result: hostbyte=0x00
driverbyte=0x08
[ 103.403769] sd 7:0:0:0: [sdc] Sense Key : 0xb [current]
[ 103.403776] sd 7:0:0:0: [sdc] ASC=0x47 ASCQ=0x1
[ 103.403784] sd 7:0:0:0: [sdc] CDB: opcode=0x28 28 00 00 00 00 00 00 00
08 00
[ 103.403790] blk_update_request: I/O error, dev sdc, sector 0
[ 103.403799] Buffer I/O error on dev sdc, logical block 0, async page read
[ 103.403863] ldm_validate_partition_table(): Disk read failed.
[ 105.156930] sd 7:0:0:0: [sdc] UNKNOWN(0x2003) Result: hostbyte=0x00
driverbyte=0x08
[ 105.156944] sd 7:0:0:0: [sdc] Sense Key : 0xb [current]
[ 105.156950] sd 7:0:0:0: [sdc] ASC=0x47 ASCQ=0x1
[ 105.156958] sd 7:0:0:0: [sdc] CDB: opcode=0x28 28 00 00 ed 7f f8 00 00
01 00
[ 105.156964] blk_update_request: I/O error, dev sdc, sector 15564792
[ 105.156974] Buffer I/O error on dev sdc, logical block 1945599, async
page read
[ 106.913502] sd 7:0:0:0: [sdc] UNKNOWN(0x2003) Result: hostbyte=0x00
driverbyte=0x08
[ 106.913516] sd 7:0:0:0: [sdc] Sense Key : 0xb [current]
[ 106.913522] sd 7:0:0:0: [sdc] ASC=0x47 ASCQ=0x1
[ 106.913530] sd 7:0:0:0: [sdc] CDB: opcode=0x28 28 00 00 00 00 00 00 00
08 00
[ 106.913536] blk_update_request: I/O error, dev sdc, sector 0
[ 106.913545] Buffer I/O error on dev sdc, logical block 0, async page read
[ 108.663070] sd 7:0:0:0: [sdc] UNKNOWN(0x2003) Result: hostbyte=0x00
driverbyte=0x08
[ 108.663084] sd 7:0:0:0: [sdc] Sense Key : 0xb [current]
[ 108.663092] sd 7:0:0:0: [sdc] ASC=0x47 ASCQ=0x1
[ 108.663100] sd 7:0:0:0: [sdc] CDB: opcode=0x28 28 00 00 00 00 00 00 00
08 00
[ 108.663107] blk_update_request: I/O error, dev sdc, sector 0
[ 108.663116] Buffer I/O error on dev sdc, logical block 0, async page read
[ 110.413625] sd 7:0:0:0: [sdc] UNKNOWN(0x2003) Result: hostbyte=0x00
driverbyte=0x08
[ 110.413638] sd 7:0:0:0: [sdc] Sense Key : 0xb [current]
[ 110.413644] sd 7:0:0:0: [sdc] ASC=0x47 ASCQ=0x1
[ 110.413652] sd 7:0:0:0: [sdc] CDB: opcode=0x28 28 00 00 00 00 00 00 00
08 00
[ 110.413658] blk_update_request: I/O error, dev sdc, sector 0
[ 110.413666] Buffer I/O error on dev sdc, logical block 0, async page read
[ 110.413727] sdc: unable to read partition table
[ 112.175660] sd 7:0:0:0: [sdc] UNKNOWN(0x2003) Result: hostbyte=0x00
driverbyte=0x08
[ 112.175674] sd 7:0:0:0: [sdc] Sense Key : 0xb [current]
[ 112.175681] sd 7:0:0:0: [sdc] ASC=0x47 ASCQ=0x1
[ 112.175688] sd 7:0:0:0: [sdc] CDB: opcode=0x28 28 00 00 ed 7f 80 00 00
08 00
[ 112.175695] blk_update_request: I/O error, dev sdc, sector 15564672
[ 113.926928] sd 7:0:0:0: [sdc] UNKNOWN(0x2003) Result: hostbyte=0x00
driverbyte=0x08
[ 113.926942] sd 7:0:0:0: [sdc] Sense Key : 0xb [current]
[ 113.926950] sd 7:0:0:0: [sdc] ASC=0x47 ASCQ=0x1
[ 113.926958] sd 7:0:0:0: [sdc] CDB: opcode=0x28 28 00 00 ed 7f 80 00 00
08 00
[ 113.926965] blk_update_request: I/O error, dev sdc, sector 15564672
[ 113.926974] Buffer I/O error on dev sdc, logical block 1945584, async
page read
[ 127.996779] sd 7:0:0:0: [sdc] UNKNOWN(0x2003) Result: hostbyte=0x00
driverbyte=0x08
[ 127.996793] sd 7:0:0:0: [sdc] Sense Key : 0xb [current]
[ 127.996800] sd 7:0:0:0: [sdc] ASC=0x47 ASCQ=0x1
[ 127.996809] sd 7:0:0:0: [sdc] CDB: opcode=0x28 28 00 00 ed 7f d8 00 00
08 00
[ 127.996815] blk_update_request: I/O error, dev sdc, sector 15564760
[ 129.751457] sd 7:0:0:0: [sdc] UNKNOWN(0x2003) Result: hostbyte=0x00
driverbyte=0x08
[ 129.751471] sd 7:0:0:0: [sdc] Sense Key : 0xb [current]
[ 129.751479] sd 7:0:0:0: [sdc] ASC=0x47 ASCQ=0x1
[ 129.751487] sd 7:0:0:0: [sdc] CDB: opcode=0x28 28 00 00 00 00 00 00 00
08 00
[ 129.751493] blk_update_request: I/O error, dev sdc, sector 0
[ 129.751502] Buffer I/O error on dev sdc, logical block 0, async page read
[ 131.503084] sd 7:0:0:0: [sdc] UNKNOWN(0x2003) Result: hostbyte=0x00
driverbyte=0x08
[ 131.503101] sd 7:0:0:0: [sdc] Sense Key : 0xb [current]
[ 131.503110] sd 7:0:0:0: [sdc] ASC=0x47 ASCQ=0x1
[ 131.503118] sd 7:0:0:0: [sdc] CDB: opcode=0x28 28 00 00 00 00 00 00 00
08 00
[ 131.503125] blk_update_request: I/O error, dev sdc, sector 0
[ 131.503134] Buffer I/O error on dev sdc, logical block 0, async page read
[ 131.503176] ldm_validate_partition_table(): Disk read failed.
[ 133.251368] sd 7:0:0:0: [sdc] UNKNOWN(0x2003) Result: hostbyte=0x00
driverbyte=0x08
[ 133.251384] sd 7:0:0:0: [sdc] Sense Key : 0xb [current]
[ 133.251392] sd 7:0:0:0: [sdc] ASC=0x47 ASCQ=0x1
[ 133.251400] sd 7:0:0:0: [sdc] CDB: opcode=0x28 28 00 00 00 00 00 00 00
08 00
[ 133.251407] blk_update_request: I/O error, dev sdc, sector 0
[ 133.251416] Buffer I/O error on dev sdc, logical block 0, async page read
[ 135.002936] sd 7:0:0:0: [sdc] UNKNOWN(0x2003) Result: hostbyte=0x00
driverbyte=0x08
[ 135.002951] sd 7:0:0:0: [sdc] Sense Key : 0xb [current]
[ 135.002959] sd 7:0:0:0: [sdc] ASC=0x47 ASCQ=0x1
[ 135.002967] sd 7:0:0:0: [sdc] CDB: opcode=0x28 28 00 00 00 00 00 00 00
08 00
[ 135.002974] blk_update_request: I/O error, dev sdc, sector 0
[ 135.002983] Buffer I/O error on dev sdc, logical block 0, async page read
[ 136.755618] sd 7:0:0:0: [sdc] UNKNOWN(0x2003) Result: hostbyte=0x00
driverbyte=0x08
[ 136.755633] sd 7:0:0:0: [sdc] Sense Key : 0xb [current]
[ 136.755641] sd 7:0:0:0: [sdc] ASC=0x47 ASCQ=0x1
[ 136.755650] sd 7:0:0:0: [sdc] CDB: opcode=0x28 28 00 00 00 00 00 00 00
08 00
[ 136.755657] blk_update_request: I/O error, dev sdc, sector 0
[ 136.755667] Buffer I/O error on dev sdc, logical block 0, async page read
[ 136.755727] sdc: unable to read partition table
[ 138.514619] sd 7:0:0:0: [sdc] UNKNOWN(0x2003) Result: hostbyte=0x00
driverbyte=0x08
[ 138.514634] sd 7:0:0:0: [sdc] Sense Key : 0xb [current]
[ 138.514642] sd 7:0:0:0: [sdc] ASC=0x47 ASCQ=0x1
[ 138.514650] sd 7:0:0:0: [sdc] CDB: opcode=0x28 28 00 00 ed 7f 80 00 00
08 00
[ 138.514657] blk_update_request: I/O error, dev sdc, sector 15564672
[ 140.264795] sd 7:0:0:0: [sdc] UNKNOWN(0x2003) Result: hostbyte=0x00
driverbyte=0x08
[ 140.264809] sd 7:0:0:0: [sdc] Sense Key : 0xb [current]
[ 140.264816] sd 7:0:0:0: [sdc] ASC=0x47 ASCQ=0x1
[ 140.264824] sd 7:0:0:0: [sdc] CDB: opcode=0x28 28 00 00 ed 7f 80 00 00
08 00
[ 140.264831] blk_update_request: I/O error, dev sdc, sector 15564672
[ 140.264840] Buffer I/O error on dev sdc, logical block 1945584, async
page read
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
