On Wed, Jan 11, 2017 at 04:29:46PM +0100, Martin Blumenstingl wrote:
> Many SoC platforms have separate devices for the USB PHY which are
> registered through the generic PHY framework. These PHYs have to be
> enabled to make the USB controller actually work. They also have to be
> disabled again on shutdown/suspend.
>
> Currently (at least) the following HCI platform drivers are using custom
> code to obtain all PHYs via devicetree for the roothub/controller and
> disable/enable them when required:
> - ehci-platform.c has ehci_platform_power_{on,off}
> - xhci-mtk.c has xhci_mtk_phy_{init,exit,power_on,power_off}
> - ohci-platform.c has ohci_platform_power_{on,off}
>
> These drivers are not using the generic devicetree USB device bindings
> yet which were only introduced recently (documentation is available in
> devicetree/bindings/usb/usb-device.txt).
> With this new driver the usb2-phy and usb3-phy can be specified directly
> in the child-node of the corresponding port of the roothub via
> devicetree. This can be extended by not just parsing PHYs (some of the
> other drivers listed above are for example also parsing a list of clocks
> as well) when required.
>
> Signed-off-by: Martin Blumenstingl <[email protected]>
> ---
> .../devicetree/bindings/usb/usb-roothub.txt | 41 ++++++
> drivers/usb/host/Kconfig | 3 +
> drivers/usb/host/Makefile | 2 +
> drivers/usb/host/platform-roothub.c | 146
> +++++++++++++++++++++
> drivers/usb/host/platform-roothub.h | 14 ++
> 5 files changed, 206 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/usb/usb-roothub.txt
> create mode 100644 drivers/usb/host/platform-roothub.c
> create mode 100644 drivers/usb/host/platform-roothub.h
>
> diff --git a/Documentation/devicetree/bindings/usb/usb-roothub.txt
> b/Documentation/devicetree/bindings/usb/usb-roothub.txt
> new file mode 100644
> index 000000000000..96e152d3901c
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/usb/usb-roothub.txt
> @@ -0,0 +1,41 @@
> +Generic USB root-hub Properties
> +
> +similar to the USB device bindings (documented in usb-device.txt from the
> +current directory) this provides support for configuring the root-hub.
> +
> +Required properties:
> +- compatible: should be at least one of "usb1d6b,3", "usb1d6b,2"
> +- reg: must be 0.
> +- address-cells: must be 1
> +- size-cells: must be 0
> +- a sub-node per port supports the following properties:
Make this another section with required and optional sections.
> + - reg: the port number on the root-hub (mandatory)
> + - phys: optional, from the *Generic PHY* bindings (mandatory needed when
> + phy-names is given)
> + - phy-names: optional, from the *Generic PHY* bindings; supported names
> + are "usb2-phy" or "usb3-phy"
> +
> +Example:
> + &usb1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + roothub@0 {
> + compatible = "usb1d6b,3", "usb1d6b,2";
Is this discoverable? IIRC, we had decided that ports on the root hub
are just children of the USB controller node (rather than
grandchildren). Why does that not work?
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> +
> + port@1 {
Wouldn't this normally be 0 and 1. This should probably be usb-port
rather than port to avoid OF graph overlap.
> + reg = <1>;
> + usb-phy = <&usb2_phy1>, <&usb3_phy1>;
s/usb-phy/phys/
> + phy-names = "usb2-phy", "usb3-phy";
> + };
> +
> + port@2 {
> + reg = <2>;
> + usb-phy = <&usb2_phy2>, <&usb3_phy2>;
> + phy-names = "usb2-phy", "usb3-phy";
> + };
> + };
> + }
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
