This driver is no longer needed and can be removed. The reason why
it's safe to remove this driver is that most omap devices don't have a
USB low-speed or full-speed compatible PHY installed and configured
with drivers/mfd/omap-usb-host.c. This means that devices like
beagleboard and pandaboard need to use a high-speed USB hub in order
to use devices like keyboard and mice.
Currently the only known configured for a full-speed PHY is the
mdm6600 modem on droid 4 and I've verified it works just fine with
ohci-platform.
Acked-by: Alan Stern <st...@rowland.harvard.edu>
Acked-by: Roger Quadros <rog...@ti.com>
Reviewed-by: Sebastian Reichel <sebastian.reic...@collabora.co.uk>
Signed-off-by: Tony Lindgren <t...@atomide.com>
---
drivers/usb/host/Kconfig | 6 +-
drivers/usb/host/Makefile | 1 -
drivers/usb/host/ohci-omap3.c | 211 ------------------------------------------
3 files changed, 5 insertions(+), 213 deletions(-)
delete mode 100644 drivers/usb/host/ohci-omap3.c
diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
--- a/drivers/usb/host/Kconfig
+++ b/drivers/usb/host/Kconfig
@@ -473,8 +473,12 @@ config USB_OHCI_HCD_AT91
config USB_OHCI_HCD_OMAP3
tristate "OHCI support for OMAP3 and later chips"
depends on (ARCH_OMAP3 || ARCH_OMAP4 || SOC_OMAP5)
+ select USB_OHCI_HCD_PLATFORM
default y
- ---help---
+ help
+ This option is deprecated now and the driver was removed, use
+ USB_OHCI_HCD_PLATFORM instead.
+
Enables support for the on-chip OHCI controller on
OMAP3 and later chips.
diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile
--- a/drivers/usb/host/Makefile
+++ b/drivers/usb/host/Makefile
@@ -52,7 +52,6 @@ obj-$(CONFIG_USB_OHCI_HCD_PCI) += ohci-pci.o
obj-$(CONFIG_USB_OHCI_HCD_PLATFORM) += ohci-platform.o
obj-$(CONFIG_USB_OHCI_EXYNOS) += ohci-exynos.o
obj-$(CONFIG_USB_OHCI_HCD_OMAP1) += ohci-omap.o
-obj-$(CONFIG_USB_OHCI_HCD_OMAP3) += ohci-omap3.o
obj-$(CONFIG_USB_OHCI_HCD_SPEAR) += ohci-spear.o
obj-$(CONFIG_USB_OHCI_HCD_STI) += ohci-st.o
obj-$(CONFIG_USB_OHCI_HCD_AT91) += ohci-at91.o
diff --git a/drivers/usb/host/ohci-omap3.c b/drivers/usb/host/ohci-omap3.c
deleted file mode 100644
--- a/drivers/usb/host/ohci-omap3.c
+++ /dev/null
@@ -1,211 +0,0 @@
-/*
- * ohci-omap3.c - driver for OHCI on OMAP3 and later processors
- *
- * Bus Glue for OMAP3 USBHOST 3 port OHCI controller
- * This controller is also used in later OMAPs and AM35x chips
- *
- * Copyright (C) 2007-2010 Texas Instruments, Inc.
- * Author: Vikram Pandita <vikram.pand...@ti.com>
- * Author: Anand Gadiyar <gadi...@ti.com>
- * Author: Keshava Munegowda <keshava_mgo...@ti.com>
- *
- * Based on ehci-omap.c and some other ohci glue layers
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- * TODO (last updated Feb 27, 2011):
- * - add kernel-doc
- */
-
-#include <linux/dma-mapping.h>
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/of.h>
-#include <linux/usb/otg.h>
-#include <linux/platform_device.h>
-#include <linux/pm_runtime.h>
-#include <linux/usb.h>
-#include <linux/usb/hcd.h>
-
-#include "ohci.h"
-
-#define DRIVER_DESC "OHCI OMAP3 driver"
-
-static const char hcd_name[] = "ohci-omap3";
-static struct hc_driver __read_mostly ohci_omap3_hc_driver;
-
-/*
- * configure so an HC device and id are always provided
- * always called with process context; sleeping is OK
- */
-
-/**
- * ohci_hcd_omap3_probe - initialize OMAP-based HCDs
- *
- * Allocates basic resources for this USB host controller, and
- * then invokes the start() method for the HCD associated with it
- * through the hotplug entry's driver_data.
- */
-static int ohci_hcd_omap3_probe(struct platform_device *pdev)
-{
- struct device *dev = &pdev->dev;
- struct ohci_hcd *ohci;
- struct usb_hcd *hcd = NULL;
- void __iomem *regs = NULL;
- struct resource *res;
- int ret;
- int irq;
-
- if (usb_disabled())
- return -ENODEV;
-
- if (!dev->parent) {
- dev_err(dev, "Missing parent device\n");
- return -ENODEV;
- }
-
- irq = platform_get_irq(pdev, 0);
- if (irq < 0) {
- dev_err(dev, "OHCI irq failed\n");
- return -ENODEV;
- }
-
- res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- if (!res) {
- dev_err(dev, "UHH OHCI get resource failed\n");
- return -ENOMEM;
- }
-
- regs = ioremap(res->start, resource_size(res));
- if (!regs) {
- dev_err(dev, "UHH OHCI ioremap failed\n");
- return -ENOMEM;
- }
-
- /*
- * Right now device-tree probed devices don't get dma_mask set.
- * Since shared usb code relies on it, set it here for now.
- * Once we have dma capability bindings this can go away.
- */
- ret = dma_coerce_mask_and_coherent(dev, DMA_BIT_MASK(32));
- if (ret)
- goto err_io;
-
- ret = -ENODEV;
- hcd = usb_create_hcd(&ohci_omap3_hc_driver, dev,
- dev_name(dev));
- if (!hcd) {
- dev_err(dev, "usb_create_hcd failed\n");
- goto err_io;
- }
-
- hcd->rsrc_start = res->start;
- hcd->rsrc_len = resource_size(res);
- hcd->regs = regs;
-
- pm_runtime_enable(dev);
- pm_runtime_get_sync(dev);
-
- ohci = hcd_to_ohci(hcd);
- /*
- * RemoteWakeupConnected has to be set explicitly before
- * calling ohci_run. The reset value of RWC is 0.
- */
- ohci->hc_control = OHCI_CTRL_RWC;
-
- ret = usb_add_hcd(hcd, irq, 0);
- if (ret) {
- dev_dbg(dev, "failed to add hcd with err %d\n", ret);
- goto err_add_hcd;
- }
- device_wakeup_enable(hcd->self.controller);
-
- return 0;
-
-err_add_hcd:
- pm_runtime_put_sync(dev);
- usb_put_hcd(hcd);
-
-err_io:
- iounmap(regs);
-
- return ret;
-}
-
-/*
- * may be called without controller electrically present
- * may be called with controller, bus, and devices active
- */
-
-/**
- * ohci_hcd_omap3_remove - shutdown processing for OHCI HCDs
- * @pdev: USB Host Controller being removed
- *
- * Reverses the effect of ohci_hcd_omap3_probe(), first invoking
- * the HCD's stop() method. It is always called from a thread
- * context, normally "rmmod", "apmd", or something similar.
- */
-static int ohci_hcd_omap3_remove(struct platform_device *pdev)
-{
- struct device *dev = &pdev->dev;
- struct usb_hcd *hcd = dev_get_drvdata(dev);
-
- iounmap(hcd->regs);
- usb_remove_hcd(hcd);
- pm_runtime_put_sync(dev);
- pm_runtime_disable(dev);
- usb_put_hcd(hcd);
- return 0;
-}
-
-static const struct of_device_id omap_ohci_dt_ids[] = {
- { .compatible = "ti,ohci-omap3" },
- { }
-};
-
-MODULE_DEVICE_TABLE(of, omap_ohci_dt_ids);
-
-static struct platform_driver ohci_hcd_omap3_driver = {
- .probe = ohci_hcd_omap3_probe,
- .remove = ohci_hcd_omap3_remove,
- .shutdown = usb_hcd_platform_shutdown,
- .driver = {
- .name = "ohci-omap3",
- .of_match_table = omap_ohci_dt_ids,
- },
-};
-
-static int __init ohci_omap3_init(void)
-{
- if (usb_disabled())
- return -ENODEV;
-
- pr_info("%s: " DRIVER_DESC "\n", hcd_name);
-
- ohci_init_driver(&ohci_omap3_hc_driver, NULL);
- return platform_driver_register(&ohci_hcd_omap3_driver);
-}
-module_init(ohci_omap3_init);
-
-static void __exit ohci_omap3_cleanup(void)
-{
- platform_driver_unregister(&ohci_hcd_omap3_driver);
-}
-module_exit(ohci_omap3_cleanup);
-
-MODULE_DESCRIPTION(DRIVER_DESC);
-MODULE_ALIAS("platform:ohci-omap3");
-MODULE_AUTHOR("Anand Gadiyar <gadi...@ti.com>");
-MODULE_LICENSE("GPL");
--
2.13.0
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
