Ha ha I did the exact same thing before with a zaurus .. I formatted the cf card .... ( mk2fs /dev/hde ) and wondered why the z didn't recognise it :-)
--B On Monday 30 December 2002 02:15, Gareth Williams wrote: > On Monday 30 December 2002 11:55, you wrote: > > Ok, now we're getting somewhere!! I unplugged the device AGAIN and > > rebooted. Went through the steps again and this time it created the > > devfs entry...but with errors in the log: > > > > Dec 30 11:27:17 localhost kernel: hub.c: new USB device 00:04.2-1, > > assigned address 2 > > Dec 30 11:27:17 localhost kernel: usb.c: USB device 2 (vend/prod > > 0xd7d/0x240) is not claimed by any active driver. > > Dec 30 11:27:21 localhost /etc/hotplug/usb.agent: Setup usb-storage for > > USB product d7d/240/100 > > Dec 30 11:27:21 localhost kernel: Initializing USB Mass Storage driver... > > Dec 30 11:27:21 localhost kernel: usb.c: registered new driver > > usb-storage Dec 30 11:27:21 localhost kernel: scsi1 : SCSI emulation for > > USB Mass Storage devices > > Dec 30 11:27:21 localhost kernel: Vendor: Model: USB Card > > Reader Rev: 1.06 > > Dec 30 11:27:21 localhost kernel: Type: > > Direct-Access ANSI SCSI revision: 02 > > Dec 30 11:27:21 localhost kernel: USB Mass Storage support registered. > > Dec 30 11:27:26 localhost kernel: Attached scsi removable disk sda at > > scsi1, channel 0, id 0, lun 0 > > Dec 30 11:27:26 localhost kernel: sda : READ CAPACITY failed. > > Dec 30 11:27:26 localhost kernel: sda : status = 1, message = 00, host = > > 0, driver = 08 > > Dec 30 11:27:26 localhost kernel: Current sd00:00: sense key Not Ready > > Dec 30 11:27:26 localhost kernel: Additional sense indicates Medium not > > present > > Dec 30 11:27:26 localhost kernel: sda : block size assumed to be 512 > > bytes, disk size 1GB. > > Dec 30 11:27:26 localhost kernel: /dev/scsi/host1/bus0/target0/lun0: > > I/O error: dev 08:00, sector 0 > > Dec 30 11:27:26 localhost kernel: I/O error: dev 08:00, sector 0 > > Dec 30 11:27:26 localhost kernel: I/O error: dev 08:00, sector 2097144 > > Dec 30 11:27:26 localhost kernel: I/O error: dev 08:00, sector 2097144 > > Dec 30 11:27:26 localhost kernel: I/O error: dev 08:00, sector 0 > > Dec 30 11:27:26 localhost kernel: I/O error: dev 08:00, sector 0 > > Dec 30 11:27:26 localhost kernel: ldm_validate_partition_table(): Disk > > read failed. > > Dec 30 11:27:26 localhost kernel: I/O error: dev 08:00, sector 0 > > Dec 30 11:27:26 localhost kernel: I/O error: dev 08:00, sector 2 > > Dec 30 11:27:26 localhost kernel: unable to read partition table > > > > Weird is says medium not present since I had a SM card in the reader > > when I mounted it!! I had to do the sd_mod straight away or the usb > > would time out. Anyway, once I did this I tried to mount it: > > > > [root@localhost jason]# modprobe sd_mod > > [root@localhost jason]# mount /dev/sda /mnt/cf > > /dev/sda: Input/output error > > mount: you must specify the filesystem type > > > > So I tried several ways: > > [root@localhost jason]# mount -t vfat /dev/sda /mnt/cf > > mount: wrong fs type, bad option, bad superblock on /dev/sda, > > or too many mounted file systems > > [root@localhost jason]# mount -t auto /dev/sda /mnt/cf > > /dev/sda: Input/output error > > mount: you must specify the filesystem type > > [root@localhost jason]# > > > > I used vfat cause I know these crap readers use fat by default. > > > > Why can't I mount the bugger!!?!@#$%^ =) > > > > Cheers > > > > Jason > > I don't know a lot about these, not owning one myself, but with a regular > HD you have to address a specific partition, such as /dev/hda1 (with the > number), which in turn contains the filesystem. I don't think you can have > a filesystem just on straight /dev/hda, can you? (or can you?..) Would it > be the same with this? > my 2c - I have a feeling I'm way off, but I can't think of anything else at > the moment... > > Cheers, > Gareth -- -- Bryan Hunt Freedom is nothing else but the chance to do better. -- Camus
