HI I have been working with the webcam Logitech Webcam C300 Device ID 046d:0805 for some days on Beagle board but I can not make it works
I have tested it on my Ubuntu 10.04 desktop and it works fine here is the logfile when I plug it Nov 24 09:42:08 victor-desktop kernel: [ 1914.457565] usb 1-4: USB disconnect, address 3 Nov 24 09:42:12 victor-desktop kernel: [ 1918.936020] usb 4-1: new full speed USB device using uhci_hcd and address 7 Nov 24 09:42:13 victor-desktop kernel: [ 1920.116027] usb 1-4: new high speed USB device using ehci_hcd and address 7 Nov 24 09:42:14 victor-desktop kernel: [ 1920.415046] usb 1-4: configuration #1 chosen from 1 choice Nov 24 09:42:14 victor-desktop kernel: [ 1920.415683] uvcvideo: Found UVC 1.00 device <unnamed> (046d:0805) Nov 24 09:42:14 victor-desktop kernel: [ 1920.453579] input: UVC Camera (046d:0805) as /devices/pci0000:00/0000:00:1a.7/usb1/1-4/1-4:1.0/input/input7 Then i clone the repo from git http://www.ideasonboard.org/uvc/ git clone git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git uvcvideo cd uvcvideo git remote add uvcvideo git://linuxtv.org/pinchartl/uvcvideo.git git remote update git checkout -b uvcvideo-master uvcvideo/uvcvideo-next then i make make -j5 ARCH=arm CROSS_COMPILE=arm-none-linux-gnueabi- omap3_beagle_defconfig make -j5 ARCH=arm CROSS_COMPILE=arm-none-linux-gnueabi- menuconfig And then I go to <*> Multimedia support ---> Video For Linux Video capture adapters V4L USB devices But there I can not find the module that I should enable for my webcam On the other hand with another webcam Microsoft Lifecam VX-3000 The which is not on the list works fine because the log file on my Ubuntu 10.04 desktop is Nov 24 09:53:13 victor-desktop kernel: [ 2579.616292] gspca: disconnect complete Nov 24 09:53:19 victor-desktop kernel: [ 2585.996025] usb 4-1: new full speed USB device using uhci_hcd and address 9 Nov 24 09:53:19 victor-desktop kernel: [ 2586.154201] usb 4-1: configuration #1 chosen from 1 choice Nov 24 09:53:19 victor-desktop kernel: [ 2586.157516] gspca: probing 045e:00f5 Nov 24 09:53:19 victor-desktop kernel: [ 2586.162257] sonixj: Sonix chip id: 11 Nov 24 09:53:19 victor-desktop kernel: [ 2586.164157] gspca: probe ok So I make the same that before make -j5 ARCH=arm CROSS_COMPILE=arm-none-linux-gnueabi- omap3_beagle_defconfig make -j5 ARCH=arm CROSS_COMPILE=arm-none-linux-gnueabi- menuconfig <*> Multimedia support ---> Video For Linux Video capture adapters V4L USB devices GSPCA based webcams SONIX JPEG USB Camera Driver And it works fine On my Beagleboard the log file is usb 1-2.4: new full speed USB device using ehci-omap and address 7 gspca: probing 045e:00f5 sonixj: Sonix chip id: 11 gspca: /dev/video0 created gspca: probing 045e:00f5 gspca: intf != 0 And /dev/video0 is created My qeustion is , Which is the correct module that I should enable for my Logitech c300 webcam ? Besides when I boot with the uImage from you kernel I just can see the console , but not the DVI ir VGA screen of my FS , is there any other module that I should enable in order to be able to what on any screen my video ? I am testing the video with mplayer Thanks a lot for your help Regards Victor Rodriguez _______________________________________________ Linux-uvc-devel mailing list Linux-uvc-devel@lists.berlios.de https://lists.berlios.de/mailman/listinfo/linux-uvc-devel
