On 12/19/11, Georg Singer <singer-ge...@web.de> wrote: > Hello, > > my webcam of Aspire One doesn't work. Many thanks for your help in advance. > > Error notification when i start the webcam: No supported video capture > device found! >
Hello, I also own an acer aspire one (the aoa150, but they have the same motherboard and display assembly). I also know some other people with the same laptop and they all have this issue. The webcam is actually supported, but due to a design flaw in the internal USB cable in the hinge connecting the motherboard and webcam, the webcam quits working after a few years due to bending stress in the cable. You may notice that booting your laptop in a different screens position makes the webcam work. so far the only solution I have found is to replace the webcam and the display cables. -Alex > Terminal: > > > [user@localhost ~]$ lsusb > > Bus 005 Device 001: ID 0000:0000 > > Bus 004 Device 001: ID 0000:0000 > > Bus 003 Device 001: ID 0000:0000 > > Bus 002 Device 002: ID 046d:c52f Logitech, Inc. > > Bus 002 Device 001: ID 0000:0000 > > Bus 001 Device 005: ID 064e:d101 Acer Crystal Eye Webcam > > Bus 001 Device 001: ID 0000:0000 > > > > [user@localhost ~]$ dmesg > > Linux version 2.6.23.9lw (root@localhost.localdomain) (gcc version 4.1.2 > 20070925 (Red Hat 4.1.2-33)) #105 SMP PREEMPT Fri Jun 27 18:56:59 EDT 2008 > > BIOS-provided physical RAM map: > > BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) > > BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) > > BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) > > BIOS-e820: 0000000000100000 - 000000001f376000 (usable) > > BIOS-e820: 000000001f376000 - 000000001f3bf000 (reserved) > > BIOS-e820: 000000001f3bf000 - 000000001f46d000 (usable) > > BIOS-e820: 000000001f46d000 - 000000001f4bf000 (ACPI NVS) > > BIOS-e820: 000000001f4bf000 - 000000001f4f0000 (usable) > > BIOS-e820: 000000001f4f0000 - 000000001f4ff000 (ACPI data) > > BIOS-e820: 000000001f4ff000 - 000000001f500000 (usable) > > BIOS-e820: 000000001f500000 - 0000000020000000 (reserved) > > BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) > > BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) > > BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved) > > BIOS-e820: 00000000fed1c000 - 00000000fed20000 (reserved) > > BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) > > BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved) > > 0MB HIGHMEM available. > > 501MB LOWMEM available. > > Entering add_active_range(0, 0, 128256) 0 entries of 256 used > > Zone PFN ranges: > > DMA 0 -> 4096 > > Normal 4096 -> 128256 > > HighMem 128256 -> 128256 > > Movable zone start PFN for each node > > early_node_map[1] active PFN ranges > > 0: 0 -> 128256 > > On node 0 totalpages: 128256 > > DMA zone: 32 pages used for memmap > > DMA zone: 0 pages reserved > > DMA zone: 4064 pages, LIFO batch:0 > > Normal zone: 970 pages used for memmap > > Normal zone: 123190 pages, LIFO batch:31 > > HighMem zone: 0 pages used for memmap > > Movable zone: 0 pages used for memmap > > DMI 2.4 present. > > ACPI: RSDP 000FE020, 0024 (r2 INTEL ) > > ACPI: XSDT 1F4FE120, 0064 (r1 INTEL Napa 1 1000013) > > ACPI: FACP 1F4FC000, 00F4 (r4 INTEL Napa 1 MSFT 1000013) > > ACPI: DSDT 1F4F2000, 5D05 (r1 INTEL Napa 1 MSFT 1000013) > > ACPI: FACS 1F488000, 0040 > > ACPI: SSDT 1F4FD000, 04C4 (r2 PmRef CpuPm 3000 INTL 20051117) > > ACPI: HPET 1F4FB000, 0038 (r1 INTEL Napa 1 MSFT 1000013) > > ACPI: APIC 1F4FA000, 0068 (r2 INTEL Napa 1 MSFT 1000013) > > ACPI: MCFG 1F4F9000, 003C (r1 INTEL Napa 1 MSFT 1000013) > > ACPI: ASF! 1F4F8000, 00A5 (r32 INTEL Napa 1 MSFT 1000013) > > ACPI: SLIC 1F4F1000, 0180 (r1 INTEL Napa 1 MSFT 1000013) > > ACPI: BOOT 1F4F0000, 0028 (r1 INTEL Napa 1 MSFT 1000013) > > ACPI: PM-Timer IO Port: 0x408 > > ACPI: Local APIC address 0xfee00000 > > ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) > > Processor #0 7:12 APIC version 20 > > ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) > > Processor #1 7:12 APIC version 20 > > ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) > > ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1]) > > ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0]) > > IOAPIC[0]: apic_id 4, version 32, address 0xfec00000, GSI 0-23 > > ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) > > ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) > > ACPI: IRQ0 used by override. > > ACPI: IRQ2 used by override. > > ACPI: IRQ9 used by override. > > Enabling APIC mode: Flat. Using 1 I/O APICs > > ACPI: HPET id: 0x8086a201 base: 0xfed00000 > > Using ACPI (MADT) for SMP configuration information > > Allocating PCI resources starting at 30000000 (gap: 20000000:c0000000) > > swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000 > > swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000e0000 > > swsusp: Registered nosave memory region: 00000000000e0000 - 0000000000100000 > > swsusp: Registered nosave memory region: 000000001f376000 - 000000001f3bf000 > > swsusp: Registered nosave memory region: 000000001f46d000 - 000000001f4bf000 > > swsusp: Registered nosave memory region: 000000001f4f0000 - 000000001f4ff000 > > Built 1 zonelists in Zone order. Total pages: 127254 > > Kernel command line: ro root=LABEL=linpus vga=0x311 splash=silent loglevel=1 > console=tty1 quiet nolapic_timer > > bootsplash: silent mode. > > mapped APIC to ffffb000 (fee00000) > > mapped IOAPIC to ffffa000 (fec00000) > > Enabling fast FPU save and restore... done. > > Enabling unmasked SIMD FPU exception support... done. > > Initializing CPU#0 > > PID hash table entries: 2048 (order: 11, 8192 bytes) > > Detected 1596.117 MHz processor. > > Console: colour dummy device 80x25 > > console [tty1] enabled > > Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) > > Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) > > Memory: 504104k/513024k available (1904k kernel code, 7516k reserved, 543k > data, 188k init, 0k highmem) > > virtual kernel memory layout: > > fixmap : 0xfff9b000 - 0xfffff000 ( 400 kB) > > pkmap : 0xff800000 - 0xffc00000 (4096 kB) > > vmalloc : 0xe0000000 - 0xff7fe000 ( 503 MB) > > lowmem : 0xc0000000 - 0xdf500000 ( 501 MB) > > .init : 0xc0369000 - 0xc0398000 ( 188 kB) > > .data : 0xc02dc0d8 - 0xc0363fa4 ( 543 kB) > > .text : 0xc0100000 - 0xc02dc0d8 (1904 kB) > > Checking if this processor honours the WP bit even in supervisor mode... Ok. > > hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 > > hpet0: 3 64-bit timers, 14318180 Hz > > Calibrating delay using timer specific routine.. 3196.02 BogoMIPS > (lpj=6392053) > > Mount-cache hash table entries: 512 > > CPU: After generic identify, caps: bfe9fbff 00000000 00000000 00000000 > 0040c39d 00000000 00000001 00000000 > > monitor/mwait feature present. > > using mwait in idle threads. > > CPU: L1 I cache: 32K, L1 D cache: 24K > > CPU: L2 cache: 512K > > CPU: Physical Processor ID: 0 > > CPU: After all inits, caps: bfe9fbff 00000000 00000000 00003940 0040c39d > 00000000 00000001 00000000 > > Compat vDSO mapped to ffffe000. > > Checking 'hlt' instruction... OK. > > SMP alternatives: switching to UP code > > ACPI: Core revision 20070126 > > CPU0: Intel(R) Atom(TM) CPU N270 @ 1.60GHz stepping 02 > > SMP alternatives: switching to SMP code > > Booting processor 1/1 eip 3000 > > Initializing CPU#1 > > Calibrating delay using timer specific routine.. 3191.98 BogoMIPS > (lpj=6383977) > > CPU: After generic identify, caps: bfe9fbff 00000000 00000000 00000000 > 0040c39d 00000000 00000001 00000000 > > monitor/mwait feature present. > > CPU: L1 I cache: 32K, L1 D cache: 24K > > CPU: L2 cache: 512K > > CPU: Physical Processor ID: 0 > > CPU: After all inits, caps: bfe9fbff 00000000 00000000 00003940 0040c39d > 00000000 00000001 00000000 > > CPU1: Intel(R) Atom(TM) CPU N270 @ 1.60GHz stepping 02 > > Total of 2 processors activated (6388.01 BogoMIPS). > > ENABLING IO-APIC IRQs > > ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 > > checking TSC synchronization [CPU#0 -> CPU#1]: passed. > > Brought up 2 CPUs > > PM: Fastpoweoff 1.0 > > NET: Registered protocol family 16 > > ACPI: bus type pci registered > > PCI: Using MMCONFIG > > Setting up standard PCI resources > > ACPI: EC: Look up EC in DSDT > > ACPI Error (evxfregn-0109): lawson ec 06 > > [20070126] > > ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62 > > ACPI Error (evxfregn-0109): lawson ec 06 > > [20070126] > > ACPI: System BIOS is requesting _OSI(Linux) > > ACPI: If "acpi_osi=Linux" works better, > > Please send dmidecode to linux-a...@vger.kernel.org > > ACPI: Interpreter enabled > > ACPI: (supports S0 S3 S4 S5) > > ACPI: Using IOAPIC for interrupt routing > > ACPI: Lawson Test 3 > > ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62 > > ACPI: PCI Root Bridge [PCI0] (0000:00) > > PCI quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO > > PCI quirk: region 0500-053f claimed by ICH6 GPIO > > PCI: Transparent bridge - 0000:00:1e.0 > > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] > > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P32_._PRT] > > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP1._PRT] > > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP2._PRT] > > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP3._PRT] > > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP4._PRT] > > ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 *11 12) > > ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 *11 12) > > ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12) > > ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12) > > ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 11 12) *0, disabled. > > ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11 12) *0, disabled. > > ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 10 11 12) *0, disabled. > > ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 9 10 11 12) *0, disabled. > > Linux Plug and Play Support v0.97 (c) Adam Belay > > pnp: PnP ACPI init > > ACPI: bus type pnp registered > > pnp: PnP ACPI: found 9 devices > > ACPI: ACPI bus type pnp unregistered > > SCSI subsystem initialized > > libata version 2.21 loaded. > > usbcore: registered new interface driver usbfs > > usbcore: registered new interface driver hub > > usbcore: registered new device driver usb > > PCI: Using ACPI for IRQ routing > > PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a > report > > Time: tsc clocksource has been installed. > > Clockevents: could not switch to one-shot mode:<6>Clockevents: could not > switch to one-shot mode: lapic is not functional. > > Could not switch to high resolution mode on CPU 1 > > lapic is not functional. > > Could not switch to high resolution mode on CPU 0 > > pnp: 00:01: ioport range 0x200-0x20f has been reserved > > pnp: 00:01: ioport range 0x164e-0x164f has been reserved > > pnp: 00:01: iomem range 0xe0000000-0xefffffff could not be reserved > > pnp: 00:01: iomem range 0xfed1c000-0xfed1ffff could not be reserved > > pnp: 00:01: iomem range 0xfed14000-0xfed17fff could not be reserved > > pnp: 00:01: iomem range 0xfed18000-0xfed18fff could not be reserved > > PCI: Bridge: 0000:00:1c.0 > > IO window: 5000-5fff > > MEM window: 37300000-383fffff > > PREFETCH window: 30000000-30ffffff > > PCI: Bridge: 0000:00:1c.1 > > IO window: 3000-4fff > > MEM window: 36300000-372fffff > > PREFETCH window: 31000000-320fffff > > PCI: Bridge: 0000:00:1c.2 > > IO window: 2000-2fff > > MEM window: 35200000-362fffff > > PREFETCH window: 32100000-330fffff > > PCI: Bridge: 0000:00:1c.3 > > IO window: 1000-1fff > > MEM window: 34100000-351fffff > > PREFETCH window: 33100000-340fffff > > PCI: Bridge: 0000:00:1e.0 > > IO window: disabled. > > MEM window: disabled. > > PREFETCH window: disabled. > > ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16 > > PCI: Setting latency timer of device 0000:00:1c.0 to 64 > > ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 17 (level, low) -> IRQ 17 > > PCI: Setting latency timer of device 0000:00:1c.1 to 64 > > ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 18 > > PCI: Setting latency timer of device 0000:00:1c.2 to 64 > > ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 19 > > PCI: Setting latency timer of device 0000:00:1c.3 to 64 > > PCI: Setting latency timer of device 0000:00:1e.0 to 64 > > NET: Registered protocol family 2 > > IP route cache hash table entries: 4096 (order: 2, 16384 bytes) > > TCP established hash table entries: 16384 (order: 6, 262144 bytes) > > TCP bind hash table entries: 16384 (order: 5, 196608 bytes) > > TCP: Hash tables configured (established 16384 bind 16384) > > TCP reno registered > > checking if image is initramfs...it isn't (no cpio magic); looks like an > initrd > > Freeing initrd memory: 102k freed > > Simple Boot Flag value 0x5 read from CMOS RAM was invalid > > Simple Boot Flag at 0x44 set to 0x1 > > Total HugeTLB memory allocated, 0 > > io scheduler noop registered > > io scheduler deadline registered (default) > > Boot video device is 0000:00:02.0 > > PCI: Setting latency timer of device 0000:00:1c.0 to 64 > > assign_interrupt_mode Found MSI capability > > Allocate Port Service[0000:00:1c.0:pcie00] > > Allocate Port Service[0000:00:1c.0:pcie02] > > Allocate Port Service[0000:00:1c.0:pcie03] > > PCI: Setting latency timer of device 0000:00:1c.1 to 64 > > assign_interrupt_mode Found MSI capability > > Allocate Port Service[0000:00:1c.1:pcie00] > > Allocate Port Service[0000:00:1c.1:pcie02] > > Allocate Port Service[0000:00:1c.1:pcie03] > > PCI: Setting latency timer of device 0000:00:1c.2 to 64 > > assign_interrupt_mode Found MSI capability > > Allocate Port Service[0000:00:1c.2:pcie00] > > Allocate Port Service[0000:00:1c.2:pcie02] > > Allocate Port Service[0000:00:1c.2:pcie03] > > PCI: Setting latency timer of device 0000:00:1c.3 to 64 > > assign_interrupt_mode Found MSI capability > > Allocate Port Service[0000:00:1c.3:pcie00] > > Allocate Port Service[0000:00:1c.3:pcie02] > > Allocate Port Service[0000:00:1c.3:pcie03] > > vesafb: framebuffer at 0x20000000, mapped to 0xe0080000, using 2400k, total > 7872k > > vesafb: mode is 640x480x16, linelength=1280, pages=11 > > vesafb: scrolling: redraw > > vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 > > bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 43971 > bytes,<6>...found (640x480, 43983 bytes, v3). > > Console: switching 1 lawson > > consoles lawson 0 > > Console: switching consoles 1-17 to colour frame buffer device 78x25 > > fb0: VESA VGA frame buffer device > > Real Time Clock Driver v1.12ac > > hpet_resources: 0xfed00000 is busy > > Linux agpgart interface v0.102 > > agpgart: Detected an Intel 945GME Chipset. > > agpgart: Detected 7932K stolen memory. > > agpgart: AGP aperture is 256M @ 0x20000000 > > [drm] Initialized drm 1.1.0 20060810 > > ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16 > > PCI: Setting latency timer of device 0000:00:02.0 to 64 > > [drm] Initialized i915 1.6.0 20060119 on minor 0 > > RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize > > loop: module loaded > > ata_piix 0000:00:1f.2: version 2.12 > > ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ] > > ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 17 (level, low) -> IRQ 17 > > PCI: Setting latency timer of device 0000:00:1f.2 to 64 > > scsi0 : ata_piix > > scsi1 : ata_piix > > ata1: SATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x000160a0 irq > 14 > > ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x000160a8 irq > 15 > > ata2.00: ATA-5: P-SSD1800, Ver2.Y0C, max UDMA/66 > > ata2.00: 15761088 sectors, multi 0: LBA > > ata2.00: configured for UDMA/66 > > scsi 1:0:0:0: Direct-Access ATA P-SSD1800 Ver2 PQ: 0 ANSI: 5 > > sd 1:0:0:0: [sda] 15761088 512-byte hardware sectors (8070 MB) > > sd 1:0:0:0: [sda] Write Protect is off > > sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00 > > sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support > DPO or FUA > > sd 1:0:0:0: [sda] 15761088 512-byte hardware sectors (8070 MB) > > sd 1:0:0:0: [sda] Write Protect is off > > sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00 > > sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support > DPO or FUA > > sda: sda1 sda2 > > sd 1:0:0:0: [sda] Attached SCSI disk > > sd 1:0:0:0: Attached scsi generic sg0 type 0 > > PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:MOUE] at 0x60,0x64 irq 1,12 > > i8042.c: Warning: Keylock active. > > i8042.c: Detected active multiplexing controller, rev 1.1. > > serio: i8042 KBD port at 0x60,0x64 irq 1 > > serio: i8042 AUX0 port at 0x60,0x64 irq 12 > > serio: i8042 AUX1 port at 0x60,0x64 irq 12 > > serio: i8042 AUX2 port at 0x60,0x64 irq 12 > > serio: i8042 AUX3 port at 0x60,0x64 irq 12 > > mice: PS/2 mouse device common for all mice > > ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 17 > > TCP cubic registered > > NET: Registered protocol family 1 > > NET: Registered protocol family 17 > > NET: Registered protocol family 15 > > Starting balanced_irq > > Using IPI No-Shortcut mode > > RAMDISK: Compressed image found at block 0 > > EXT2-fs warning: checktime reached, running e2fsck is recommended > > VFS: Mounted root (ext2 filesystem). > > TuxOnIce: No attempt was made to resume from any image that might exist. > > Freeing unused kernel memory: 188k freed > > Warning: unable to open an initial console. > > Synaptics Touchpad, model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04771/0xa40000 > > input: SynPS/2 Synaptics TouchPad as > /devices/platform/i8042/serio2/input/input0 > > ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 16 (level, low) -> IRQ 16 > > PCI: Setting latency timer of device 0000:00:1d.7 to 64 > > ehci_hcd 0000:00:1d.7: EHCI Host Controller > > ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 > > ehci_hcd 0000:00:1d.7: debug port 1 > > PCI: cache line size of 32 is not supported by device 0000:00:1d.7 > > ehci_hcd 0000:00:1d.7: irq 16, io mem 0x38544400 > > ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 > > usb usb1: configuration #1 chosen from 1 choice > > hub 1-0:1.0: USB hub found > > hub 1-0:1.0: 8 ports detected > > input: AT Translated Set 2 keyboard as > /devices/platform/i8042/serio0/input/input1 > > mtrr: no more MTRRs available > > Initializing USB Mass Storage driver... > > usb 1-5: new high speed USB device using ehci_hcd and address 3 > > usb 1-5: configuration #1 chosen from 1 choice > > usbcore: registered new interface driver usb-storage > > USB Mass Storage support registered. > > ACPI: SSDT 1F380C90, 0239 (r2 PmRef Cpu0Ist 3000 INTL 20051117) > > ACPI: SSDT 1F37FE10, 01C7 (r2 PmRef Cpu0Cst 3001 INTL 20051117) > > ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) > > ACPI: Processor [CPU0] (supports 8 throttling states) > > ACPI: SSDT 1F380F10, 00D0 (r2 PmRef Cpu1Ist 3000 INTL 20051117) > > ACPI: SSDT 1F37EF10, 0083 (r2 PmRef Cpu1Cst 3000 INTL 20051117) > > ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3]) > > ACPI: Processor [CPU1] (supports 8 throttling states) > > USB Universal Host Controller Interface driver v3.0 > > ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 16 > > PCI: Setting latency timer of device 0000:00:1d.0 to 64 > > uhci_hcd 0000:00:1d.0: UHCI Host Controller > > uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 > > uhci_hcd 0000:00:1d.0: irq 16, io base 0x00006080 > > usb usb2: configuration #1 chosen from 1 choice > > hub 2-0:1.0: USB hub found > > hub 2-0:1.0: 2 ports detected > > input: Power Button (FF) as /devices/virtual/input/input2 > > ACPI: Power Button (FF) [PWRF] > > input: Power Button (CM) as /devices/virtual/input/input3 > > ACPI: Power Button (CM) [PWRB] > > input: Lid Switch as /devices/virtual/input/input4 > > ACPI: Lid Switch [LID0] > > input: Sleep Button (CM) as /devices/virtual/input/input5 > > ACPI: Sleep Button (CM) [SLPB] > > ACPI: AC Adapter [ACAD] (on-line) > > ACPI: Battery Slot [BAT1] (battery present) > > input: Video Bus as /devices/virtual/input/input6 > > ACPI: Video Device [OVGA] (multi-head: yes rom: yes post: no) > > ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 17 > > PCI: Setting latency timer of device 0000:00:1d.1 to 64 > > uhci_hcd 0000:00:1d.1: UHCI Host Controller > > uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 > > uhci_hcd 0000:00:1d.1: irq 17, io base 0x00006060 > > usb usb3: configuration #1 chosen from 1 choice > > hub 3-0:1.0: USB hub found > > hub 3-0:1.0: 2 ports detected > > ath_hal: module license 'Proprietary' taints kernel. > > ath_hal: 0.9.17.1 (AR5212, RF5111, RF5112, RF2413, RF5413) > > ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18 > > PCI: Setting latency timer of device 0000:00:1d.2 to 64 > > uhci_hcd 0000:00:1d.2: UHCI Host Controller > > uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 > > uhci_hcd 0000:00:1d.2: irq 18, io base 0x00006040 > > usb usb4: configuration #1 chosen from 1 choice > > hub 4-0:1.0: USB hub found > > hub 4-0:1.0: 2 ports detected > > ath_dfs: Version 2.0.0 > > Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved > > ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 19 (level, low) -> IRQ 19 > > PCI: Setting latency timer of device 0000:00:1d.3 to 64 > > uhci_hcd 0000:00:1d.3: UHCI Host Controller > > uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5 > > uhci_hcd 0000:00:1d.3: irq 19, io base 0x00006020 > > usb usb5: configuration #1 chosen from 1 choice > > hub 5-0:1.0: USB hub found > > hub 5-0:1.0: 2 ports detected > > usb 2-2: new full speed USB device using uhci_hcd and address 2 > > wlan: 0.8.4.2 (Atheros/multi-bss) > > r8101 Fast Ethernet driver 1.008.08-2-1-NAPI loaded > > ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 17 (level, low) -> IRQ 17 > > PCI: Setting latency timer of device 0000:02:00.0 to 64 > > eth0: Identified chip type is 'RTL8102E'. > > eth0: RTL8101E at 0xe0340000, 00:1e:68:a6:96:3e, IRQ 17 > > ath_rate_atheros: Version 2.0.1 > > Copyright (c) 2001-2004 Atheros Communications, Inc, All Rights Reserved > > intel_rng: FWH not detected > > usb 2-2: configuration #1 chosen from 1 choice > > ath_pci: 0.9.4.5 (Atheros/multi-bss) > > ath_pci: Acer-5.3.2.14-2008-Sep-23 > > ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 18 (level, low) -> IRQ 18 > > PCI: Setting latency timer of device 0000:03:00.0 to 64 > > ##################################################### > > ####################WLAN ID:001c #################### > > ##################################################### > > Setting ah_eepromDetach > > Linux video capture interface: v2.00 > > uvcvideo: Found UVC 1.00 device Acer Crystal Eye webcam (064e:d101) > > uvcvideo: Failed to query (1) UVC control 2 (unit 0) : -32 (exp. 26). > > uvcvideo: Failed to initialize the device (-5). > > usbcore: registered new interface driver uvcvideo > > USB Video Class driver (SVN r215) > > SAMSoft library init ... > > ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 16 > > PCI: Setting latency timer of device 0000:00:1b.0 to 64 > > ForteMedia SAM-Soft Library Loaded! > > ALC INIT<6>usbcore: registered new interface driver hiddev > > input: Logitech USB Receiver as > /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/input/input7 > > input: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:1d.0-2 > > input: Logitech USB Receiver as > /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.1/input/input8 > > input,hiddev96: USB HID v1.11 Device [Logitech USB Receiver] on > usb-0000:00:1d.0-2 > > usbcore: registered new interface driver usbhid > > drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver > > Marking TSC unstable due to: possible TSC halt in C2. > > Time: hpet clocksource has been installed. > > Clockevents: could not switch to one-shot mode: lapic is not functional. > > Clockevents: could not switch to one-shot mode: lapic is not functional. > > Could not switch to high resolution mode on CPU 1 > > Could not switch to high resolution mode on CPU 0 > > wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps > > wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps > 24Mbps 36Mbps 48Mbps 54Mbps > > wifi0: mac 14.2 phy 7.0 radio 10.2 > > wifi0: Use hw queue 1 for WME_AC_BE traffic > > wifi0: Use hw queue 0 for WME_AC_BK traffic > > wifi0: Use hw queue 2 for WME_AC_VI traffic > > wifi0: Use hw queue 3 for WME_AC_VO traffic > > wifi0: Use hw queue 8 for CAB traffic > > wifi0: Use hw queue 9 for beacons > > wifi0: Atheros 5212: mem=0x35200000, irq=18 > > Clocksource tsc unstable (delta = -138924304 ns) > > pci_hotplug: PCI Hot Plug PCI Core version: 0.5 > > pciehp: HPC vendor_id 8086 device_id 27d0 ss_vid 0 ss_did 0 > > Load service driver hpdriver on pcie device 0000:00:1c.0:pcie02 > > pciehp: HPC vendor_id 8086 device_id 27d2 ss_vid 0 ss_did 0 > > pciehp: Device 0000:02:00.0 already exists at 2:0, cannot hot-add > > pciehp: Cannot add device 0x2:0 > > Load service driver hpdriver on pcie device 0000:00:1c.1:pcie02 > > pciehp: HPC vendor_id 8086 device_id 27d4 ss_vid 0 ss_did 0 > > pciehp: Device 0000:03:00.0 already exists at 3:0, cannot hot-add > > pciehp: Cannot add device 0x3:0 > > Load service driver hpdriver on pcie device 0000:00:1c.2:pcie02 > > pciehp: HPC vendor_id 8086 device_id 27d6 ss_vid 0 ss_did 0 > > Load service driver hpdriver on pcie device 0000:00:1c.3:pcie02 > > pciehp: PCI Express Hot Plug Controller Driver version: 0.4 > > sdhci: Secure Digital Host Controller Interface driver > > sdhci: Copyright(c) Pierre Ossman > > PM: Fastpoweroff, default profile added > > wlan: mac acl policy registered > > <ath_vap_create> sc_softled = 0 > > ath_vap_create: LED ON > > r8101: eth0: link down > > ath_stop_locked: LED OFF 2 > > Adding 1052248k swap on /dev/sda2. Priority:-1 extents:1 across:1052248k > > aufs 20080505 > > usb 1-5: USB disconnect, address 3 > > usb 1-5: new high speed USB device using ehci_hcd and address 4 > > usb 1-5: device not accepting address 4, error -71 > > usb 1-5: new high speed USB device using ehci_hcd and address 5 > > usb 1-5: configuration #1 chosen from 1 choice > > uvcvideo: Found UVC 1.00 device Acer Crystal Eye webcam (064e:d101) > > uvcvideo: Failed to query (1) UVC control 2 (unit 0) : -32 (exp. 26). > > uvcvideo: Failed to initialize the device (-5). > > process `skype' is using obsolete setsockopt SO_BSDCOMPAT > > controllers format 0x13. > > controllers format 0x13. > > controllers format 0x13. > > [user@localhost ~]$ > > > > > > > > -- Alexander Lam _______________________________________________ Linux-uvc-devel mailing list Linux-uvc-devel@lists.berlios.de https://lists.berlios.de/mailman/listinfo/linux-uvc-devel
