Attempting to follow
http://wireless.kernel.org/en/users/Documentation/iw#Setting_TX_power
I get:
sudo iw dev wlan1 set txpower fixed 14
command failed: Invalid argument (-22)
Same error if I raise or lower this number.
My environment:
+ Ubuntu 14.10 (also reproducible in 14.04)
+ (Also reproducible in 3.13.x)
uname -a
Linux acer-pc 3.16.0-29-generic #39-Ubuntu SMP Mon Dec 15 22:27:29 UTC
2014 x86_64 x86_64 x86_64 GNU/Linux
+ I am in the US regulatory domain.
+ wlan1
usb-devices
T: Bus=02 Lev=02 Prnt=02 Port=01 Cnt=01 Dev#= 3 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=050d ProdID=845a Rev=02.00
S: Manufacturer=Manufacturer Realtek
S: Product=Belkin USB Wireless Adaptor
S: SerialNumber=00e04c000001
C: #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 4 Cls=ff(vend.) Sub=ff Prot=ff Driver=r8712u
+ wlan0
lspci -vvnn
03:00.0 Network controller [0280]: Qualcomm Atheros AR9287 Wireless
Network Adapter (PCI-Express) [168c:002e] (rev 01)
Subsystem: Foxconn International, Inc. Device [105b:e034]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at c0500000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: ath9k
+ I don't have network-manager or wicd installed. I've configured both
wlan0 and wlan1 in /etc/network/interfaces :
# interfaces(5) file used by ifup(8) and ifdown(8)
auto lo wlan0 wlan1
iface lo inet loopback
# wlan0 access point
iface wlan0 inet static
address 10.0.0.1
netmask 255.255.255.240
gateway 10.0.0.1
wireless-mode Master
# wlan1 managed mode
iface wlan1 inet static
address 192.168.1.10
network 192.168.1.0
netmask 255.255.255.0
gateway 192.168.1.1
wpa-bssid XX:XX:XX:XX:XX:XX
wpa-ssid SSID
wpa-psk PASSWORD
+ Strangely, the following does not show a phy0 and a phy1, but both
wlan0 and wlan1 work fine:
iw list
Wiphy phy0
max # scan SSIDs: 4
max scan IEs length: 2257 bytes
Coverage class: 0 (up to 0m)
Device supports RSN-IBSS.
Device supports AP-side u-APSD.
Device supports T-DLS.
Supported Ciphers:
* WEP40 (00-0f-ac:1)
* WEP104 (00-0f-ac:5)
* TKIP (00-0f-ac:2)
* CCMP (00-0f-ac:4)
* CMAC (00-0f-ac:6)
Available Antennas: TX 0x3 RX 0x3
Configured Antennas: TX 0x3 RX 0x3
Supported interface modes:
* IBSS
* managed
* AP
* AP/VLAN
* WDS
* monitor
* mesh point
* P2P-client
* P2P-GO
Band 1:
Capabilities: 0x11ee
HT20/HT40
SM Power Save disabled
RX HT20 SGI
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 3839 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT TX/RX MCS rate indexes supported: 0-15
Bitrates (non-HT):
* 1.0 Mbps
* 2.0 Mbps (short preamble supported)
* 5.5 Mbps (short preamble supported)
* 11.0 Mbps (short preamble supported)
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Frequencies:
* 2412 MHz [1] (16.0 dBm)
* 2417 MHz [2] (16.0 dBm)
* 2422 MHz [3] (16.0 dBm)
* 2427 MHz [4] (16.0 dBm)
* 2432 MHz [5] (16.0 dBm)
* 2437 MHz [6] (16.0 dBm)
* 2442 MHz [7] (16.0 dBm)
* 2447 MHz [8] (16.0 dBm)
* 2452 MHz [9] (16.0 dBm)
* 2457 MHz [10] (16.0 dBm)
* 2462 MHz [11] (16.0 dBm)
* 2467 MHz [12] (disabled)
* 2472 MHz [13] (disabled)
* 2484 MHz [14] (disabled)
Supported commands:
* new_interface
* set_interface
* new_key
* start_ap
* new_station
* new_mpath
* set_mesh_config
* set_bss
* authenticate
* associate
* deauthenticate
* disassociate
* join_ibss
* join_mesh
* remain_on_channel
* set_tx_bitrate_mask
* frame
* frame_wait_cancel
* set_wiphy_netns
* set_channel
* set_wds_peer
* tdls_mgmt
* tdls_oper
* probe_client
* set_noack_map
* register_beacons
* start_p2p_device
* set_mcast_rate
* Unknown command (104)
* connect
* disconnect
Supported TX frame types:
* IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80
0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70
0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80
0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70
0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70
0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70
0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70
0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70
0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
Supported RX frame types:
* IBSS: 0x40 0xb0 0xc0 0xd0
* managed: 0x40 0xd0
* AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* mesh point: 0xb0 0xc0 0xd0
* P2P-client: 0x40 0xd0
* P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* P2P-device: 0x40 0xd0
software interface modes (can always be added):
* AP/VLAN
* monitor
valid interface combinations:
* #{ managed } <= 2048, #{ AP, mesh point } <= 8, #{
P2P-client, P2P-GO } <= 1,
total <= 2048, #channels <= 1, STA/AP BI must match
* #{ WDS } <= 2048,
total <= 2048, #channels <= 1, STA/AP BI must match
HT Capability overrides:
* MCS: ff ff ff ff ff ff ff ff ff ff
* maximum A-MSDU length
* supported channel width
* short GI for 40 MHz
* max A-MPDU length exponent
* min MPDU start spacing
Device supports TX status socket option.
Device supports HT-IBSS.
Device supports low priority scan.
Device supports scan flush.
Device supports AP scan.
When I run wavemon -i wlan1 it does not show a tx-power. However, if I
run wavemon on a different computer with the following chipset, it
does show tx-power:
lspci -vvnn
02:00.0 Network controller [0280]: Qualcomm Atheros QCA9565 / AR9565
Wireless Network Adapter [168c:0036] (rev 01)
Subsystem: Lenovo Device [17aa:3026]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 36
Region 0: Memory at f0800000 (64-bit, non-prefetchable) [size=512K]
Expansion ROM at f0880000 [disabled] [size=64K]
Capabilities: <access denied>
Kernel driver in use: ath9k
However, this chipset also cannot have the txpower changed for a
different reason:
sudo iw dev wlan0 set txpower fixed 14
command failed: Operation not supported (-95)
I've spent the better part of this weekend looking through countless
forums, mailing lists, man pages, etc. and have not been provided a
clear answer to any of this. Anything you could do to clear this up is
greatly appreciated.
Thank you for your time and consideration in this matter.
Christopher M. Penalver
E-Mail: [email protected]
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
