commit 330b4e4be937 ("brcmfmac: Add wowl support for SDIO devices.")
changed the behaviour by removing the MMC_PM_KEEP_POWER flag for
non-wowl scenario, which needs to be restored. Another necessary
change is to mark the card as being non-removable. With this in place
the suspend resume test passes successfully doing:
# echo devices > /sys/power/pm_test
# echo mem > /sys/power/state
Note that power may still be switched off when system is going
in S3 state.
Reported-by: Fu, Zhonghui <<zhonghui...@linux.intel.com>
Reviewed-by: Pieter-Paul Giesberts <piete...@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <fran...@broadcom.com>
Signed-off-by: Arend van Spriel <ar...@broadcom.com>
---
drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c | 18 +++++++++++++-----
1 file changed, 13 insertions(+), 5 deletions(-)
diff --git a/drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c
b/drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c
index 9b508bd..8a69544 100644
--- a/drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c
+++ b/drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c
@@ -1011,6 +1011,14 @@ static int brcmf_sdiod_remove(struct brcmf_sdio_dev
*sdiodev)
return 0;
}
+static void brcmf_sdiod_host_fixup(struct mmc_host *host)
+{
+ /* runtime-pm powers off the device */
+ pm_runtime_forbid(host->parent);
+ /* avoid removal detection upon resume */
+ host->caps |= MMC_CAP_NONREMOVABLE;
+}
+
static int brcmf_sdiod_probe(struct brcmf_sdio_dev *sdiodev)
{
struct sdio_func *func;
@@ -1076,7 +1084,7 @@ static int brcmf_sdiod_probe(struct brcmf_sdio_dev
*sdiodev)
ret = -ENODEV;
goto out;
}
- pm_runtime_forbid(host->parent);
+ brcmf_sdiod_host_fixup(host);
out:
if (ret)
brcmf_sdiod_remove(sdiodev);
@@ -1246,15 +1254,15 @@ static int brcmf_ops_sdio_suspend(struct device *dev)
brcmf_sdiod_freezer_on(sdiodev);
brcmf_sdio_wd_timer(sdiodev->bus, 0);
+ sdio_flags = MMC_PM_KEEP_POWER;
if (sdiodev->wowl_enabled) {
- sdio_flags = MMC_PM_KEEP_POWER;
if (sdiodev->pdata->oob_irq_supported)
enable_irq_wake(sdiodev->pdata->oob_irq_nr);
else
- sdio_flags = MMC_PM_WAKE_SDIO_IRQ;
- if (sdio_set_host_pm_flags(sdiodev->func[1], sdio_flags))
- brcmf_err("Failed to set pm_flags %x\n", sdio_flags);
+ sdio_flags |= MMC_PM_WAKE_SDIO_IRQ;
}
+ if (sdio_set_host_pm_flags(sdiodev->func[1], sdio_flags))
+ brcmf_err("Failed to set pm_flags %x\n", sdio_flags);
return 0;
}
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
