Johannes Berg <[email protected]> writes:
>> + * This driver was written as a replacement for the vendor provided
>> + * rtl8723au driver. As the Realtek 8xxx chips are very similar in
>> + * their programming interface, I have started adding support for
>> + * additional 8xxx chips like the 8192cu, 8188cus, etc.
>
> That last sentence here seems like it might be more suitable in the
> commit message then here - you'll surely forget to update it ;)
>
>> +> > /*
>> +> > * MBOX ready?
>> +> > */
>> +> > retry = 100;
>> +> > do {
>> +> > > val8 = rtl8xxxu_read8(priv, REG_HMTFR);
>> +> > > if (!(val8 & BIT(mbox_nr)))
>> +> > > > break;
>> +> > } while (retry--);
>
> Seems fishy without any delay in the loop?
The access to USB registers introduces a delay automatically.
>> +> > val32 = rtl8xxxu_read32(priv, REG_OFDM0_TRX_PATH_ENABLE);
>> +> > val32 &= ~OFDM_RF_PATH_TX_MASK;
>> +> > if (priv->tx_paths == 2)
>
> "TX path" is very uncommon language for this... I'd suggest changing
> all that to "TX stream" or "TX chain"?
>
>> +> > if (priv->rf_paths == 2)
>
> Similar here - and should that be RX not RF?
I stuck with the naming from the vendor driver. The chip has antennas
and internal paths or streams and if I understand it right, granted not
having any specs whatsoever, I may have gotten some of it wrong, you can
wire path B to antenna A and vice versa. So it may only have one antenna
but uses path B to communicate.
>> +static int rtl8723a_channel_to_group(int channel)
>> +{
>> +> > int group;
>> +
>> +> > if (channel < 4)
>> +> > > group = 0;
>> +> > else if (channel < 10)
>> +> > > group = 1;
>> +> > else
>> +> > > group = 2;
>> +
>> +> > return group;
>> +}
>
> Could remove the group variable, it's kinda pointless - just return
> immediately?
>
> if (channel < 4)
> return 0;
> if (channel < 10)
> return 1;
> return 2;
I dislike returns in the middle of the function, but granted thats a
style preference.
>> +> > /* Poll for data read */
>> +> > val32 = rtl8xxxu_read32(priv, REG_EFUSE_CTRL);
>> +> > for (i = 0; i < RTL8XXXU_MAX_REG_POLL; i++) {
>> +> > > val32 = rtl8xxxu_read32(priv, REG_EFUSE_CTRL);
>> +> > > if (val32 & BIT(31))
>> +> > > > break;
>> +> > }
>
> Hmm, similar poll loop like above w/o any delay?
> A few more seem to exist too.
For USB register reading, not having a delay should be fine, if we
looked at adding support for PCI, a delay is definitely needed.
>> +> > > > for (i = 0; i < EFUSE_MAX_WORD_UNIT; i++) {
>> +> > > > > /* Check word enable condition in the section */
>> +> > > > > if (!(word_mask & BIT(i))) {
>> +> > > > > > ret = rtl8xxxu_read_efuse8(priv,
>> +> > > > > > > > > efuse_addr++,
>> +> > > > > > > > > &val8);
>> +> > > > > > if (ret)
>> +> > > > > > > goto exit;
>> +> > > > > > priv->efuse_wifi.raw[map_addr++] = val8;
>> +
>> +> > > > > > ret = rtl8xxxu_read_efuse8(priv,
>> +> > > > > > > > > efuse_addr++,
>> +> > > > > > > > > &val8);
>> +> > > > > > if (ret)
>> +> > > > > > > goto exit;
>> +> > > > > > priv->efuse_wifi.raw[map_addr++] = val8;
>> +> > > > > } else
>> +> > > > > > map_addr += 2;
>> +> > > > }
>
> seems like it might better be in a helper function :)
Maybe :)
>> +static int rtl8xxxu_init_phy_regs(struct rtl8xxxu_priv *priv,
>> +> > > > > struct rtl8xxxu_reg32val *array)
>> +{
>> +> > int i, ret;
>> +> > u16 reg;
>> +> > u32 val;
>> +
>> +> > for (i = 0; ; i++) {
>> +> > > reg = array[i].reg;
>> +> > > val = array[i].val;
>> +
>> +> > > if (reg == 0xffff && val == 0xffffffff)
>> +> > > > break;
> Maybe passing ARRAY_SIZE to these would be nicer than having to they're
> terminated? Dunno though, might be a lot of infrastructure to do that.
I prefer terminated arrays rather than calculating sizes, but it is also
a style issue.
> Ugh, getting too long for me - anything in particular I should look at?
> :)
Anything related to doing things correctly wrt to the mac80211 API would
be awesome.
Cheers,
Jes
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
