From: Jes Sorensen <[email protected]>
Hi,
This is a rather large set of patches adding support for rtl8723bu
devices, as well as containing some code for rtl8192eu devices.
I started working on 8192eu support at the beginning but later
switched over and completed 8723bu support, before finally completing
8192eu support. The two new devices share a lot of new features not
found in the older generation parts (8723au/8188cu/8192cu/8188ru).
I am holding back the 8192eu support for now, in order to reduce the
size of the patch set (I have another 60 patches that goes on top of
this set with 8192eu support and additional bug fixes). Given that
support for the two devices is intermingled, trying to disentangle it
is pretty much impossible at this point, and risks breaking the code.
This applies on top of wireless-drivers-next as of today 2016-02-29.
Cheers,
Jes
Jakub Sitnicki (5):
rtl8xxxu: Don't check for illegal offset when reading from efuse
rtl8xxxu: Skip disabled efuse words early
rtl8xxxu: rtl8723au: Introduce a pointer to efuse
rtl8xxxu: rtl8192cu: Introduce a pointer to efuse
rtl8xxxu: rtl8192eu: Map out EFUSE TX power area
Jes Sorensen (108):
rtl8xxxu: Add initial code to parse rtl8192eu efuse
rtl8xxxu: Identify chip vendors correctly
rtl8xxxu: Use 1024 byte block loads for 8192eu firmware
rtl8xxxu: Add rtl8192eu_nic.bin to the MODULE_FIRMWARE list
rtl8xxxu: Implment rtl8192eu_power_on()
rtl8xxxu: Add rtl8xxxu_auto_llt_table()
rtl8xxxu: Init page boundaries before starting the firmware
rtl8xxxu: Init the LLT after we start the firmware
rtl8xxxu: Fix incorrect test for auto LLT failure
rtl8xxxu: Kludge to drop incorrect USB OUT EP for 8192EU
rtl8xxxu: Init REG_HIMR[01] for 8192eu parts
rtl8xxxu: Initial rtl8723bu chip identification
rtl8xxxu: Add rtl8723bu_parse_efuse() and 8723bu efuse definition
rtl8xxxu: Use 1024 byte writes for writing 8723bu firmware
rtl8xxxu: Only setup USB interrupts for parts which support it
rtl8xxxu: Add rtl8723b_phy_1t_init_table
rtl8xxxu: Add rtl8723bu_radioa_1t_init_table
rtl8xxxu: Add rtl8723bu_phy_init_antenna_selection()
rtl8xxxu: Add rtl8723b_mac_init_table
rtl8xxxu: Add 8723by AGC table
rtl8xxxu: Handle 32 bit mailbox extension regs found on
8723bu/8192eu/8812
rtl8xxxu: Add some missing register definitions for 8723bu
rtl8xxxu: Group USB fixups together for all chips
rtl8xxxu: Add definitions for new generation h2c commands
rtl8xxxu: rtl8192eu_parse_efuse(): Use a pointer to the struct
rtl8192eu_efuse
rtl8xxxu: rtl8723bu_parse_efuse(): Use a pointer to the struct
rtl8723bu_efuse
rtl8xxxu: rtl8xxxu_h2c_cmd(): Add size argument
rtl8xxxu: Do BT_WLAN_CALIBRATION before doing IQK calibration
rtl8xxxu: Do not overwrite rtl8xxxu_debug for untested chips
rtl8xxxu: Use correct formatting type to print sizeof()
rtl8xxxu: Make rtl8xxxu_add_path_on() use device specific init values
rtl8xxxu: Add a couple of new register definitions
rtl8xxxu: First stab at adding IQK calibration for 8723bu parts
rtl8xxxu: Handle S0S1 register in lc_calibrate()
rtl8xxxu: Do LC calibration before IQK calibration
rtl8xxxu: Remove backing up certain registers, which was never used
rtl8xxxu: Initial implementation of rtl8723bu_config_channel()
rtl8xxxu: Initial rtl8723bu_init_bt() code
rtl8xxxu: Remove unused variable
rtl8xxxu: Improve 8723bu init code
rtl8xxxu: Do not ignore wlan activity on 8723bu
rtl8xxxu: Set the right type for ps tdma on 8723bu
rtl8xxxu: Add rtl8723bu (nextgen) rx descriptor definition
rtl8xxxu: Handle 8723bu style rx descriptors
rtl8xxxu: Initial functionality to handle C2H events for 8723bu
rtl8xxxu: Handle BT register writes and MP_OPER events
rtl8xxxu: Issue BT_INFO command
rtl8xxxu: Do not set REG_AFE_XTAL_CTRL on 8723bu
rtl8xxxu: Implement 8723bu power on sequence
rtl8xxxu: Setup LLT before downloading firmware
rtl8xxxu: Additional fixes for 8723bu
rtl8xxxu: Handle XTAL_K value in efuse specific location
rtl8xxxu: Another 8723bu patch for rtl8xxxu_init_phy_bb()
rtl8xxxu: Another 8723bu magic register set during init
rtl8xxxu: Init H2C command register for 8723bu
rtl8xxxu: 80M spur hack is for 8723au only
rtl8xxxu: Do queue init in same order as 8723bu vendor driver
rtl8xxxu: Do not set FPGA0_TX_INFO for 8723bu and use a larger PBP
page size
rtl8xxxu: Set RX boundary for 8723bu
rtl8xxxu: Initialize burst parameters for 8723bu
rtl8xxxu: Call device specific _config_channel()
rtl8xxxu: 8723bu lock phy after RF init
rtl8xxxu: Add REG_DWBCN1_CTRL_8723B define
rtl8xxxu: Group chip quirks together
rtl8xxxu: Setup RX aggregation
rtl8xxxu: Add missing blank space in front of bracket
rtl8xxxu: Implement init_statistics for 8723bu
rtl8xxxu: RF_T_METER is different on the newer chips
rtl8xxxu: Set WLAN_ACT_CONTROL per vendor driver setting
rtl8xxxu: 8723bu: REG_BT_COEX_TABLE4 is only 8 bits
rtl8xxxu: Use name for REG_RFE_BUFFER rather than hard coded value
rtl8xxxu: Use REG_RFE_CTRL_ANTA_SRC rather than hard coded value
rtl8xxxu: Setup coex table correctly (hopefully)
rtl8xxxu: Do not use hard-wired RF enable settings for 8723bu
rtl8xxxu: Correct struct rtl8723bu_efuse to list power bases correctly
rtl8xxxu: Introduce set_tx_power() fileop and a new 8723b dummy
derivative
rtl8xxxu: Use size of source pointer when copying efuse data
rtl8xxxu: Bump TX power arrays to handle larger channel groups
rtl8xxxu: Parse efuse power indices for 8723bu
rtl8xxxu: Set 8723bu TX power for CCK and OFDM rates
rtl8xxxu: Set 8723bu MCS TX power
rtl8xxxu: Set the correct thermal meter register for 8723bu
rtl8xxxu: Add definition for 8723bu tx descriptor
rtl8xxxu: Handle 40 byte TX descriptors for rtl8723bu
rtl8xxxu: Do not unconditionally print debug info in
rtl8723bu_handle_c2h()
rtl8xxxu: Add additional tx descriptor bits for data word 0
rtl8xxxu: Add more 40 byte TX desc bit definitions
rtl8xxxu: Set the correct TX descriptor bits for agg and break on
8723b
rtl8xxxu: Set sequence number correctly for 40 byte TX descriptors
rtl8723au: Update TX descriptor words 4 and 5 definitions
rtl8xxxu: TX RTS rate is word 4 for 8723a
rtl8xxxu: Improve handling of txdesc32 vs txdesc40 handling
rtl8xxxu: Do not parse RX descriptor info for C2H packets
rtl8xxxu: Define 8723b H2C ramask command structure
rtl8xxxu: Implement basic 8723b specific update_rate_mask() function
rtl8xxxu: Report media status using the correct H2C command for 8723bu
rtl8xxxu: Dump contents of unhandled C2H events
rtl8xxxu: Process C2H RA_REPORT events for 8723bu
rtl8xxxu: Pass RX rate to rx_parse_phystats and enable phystats for
rtl8723bu
rtl8xxxu: Remove unncessary semicolon
rtl8xxxu: convert rtl8723bu_init_bt() into rtl8723b_enable_rf()
rtl8xxxu: Use define for REG_PWR_DATA bits
rtl8xxxu: Implement 8723bu specific disable_rf() function
rtl8xxxu: Implement device specific power_off function
rtl8xxxu: Flush FIFO before powering down devices
rtl8xxxu: Print a warning if flushing the FIFO fails
rtl8xxxu: Use correct 8051 reset function for 8723b parts
rtl8xxxu: Temporarily disable 8192eu device init
drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c | 3524 +++++++++++++++++---
drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.h | 691 +++-
.../net/wireless/realtek/rtl8xxxu/rtl8xxxu_regs.h | 97 +-
3 files changed, 3852 insertions(+), 460 deletions(-)
--
2.5.0
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
