On Fri, Mar 18, 2016 at 04:03:51AM -0700, Amitkumar Karwar wrote:
> From: Xinming Hu <[email protected]>
>
> Add device tree binding documentation for MARVELL's sd8xxx
> (sd8897 and sd8997) wlan chip.
>
> Signed-off-by: Xinming Hu <[email protected]>
> Signed-off-by: Amitkumar Karwar <[email protected]>
> ---
> Listing changelist for both 1/2 and 2/2 patches
> v3: Don't update adapter->dt_node if mwifiex_plt_dev is NULL
>
> v4: a)Corrected the 'name' and 'compatible' property names.(Arnd Bergmann and
> Rob
> Herring)
> b)Patch description wraped in 72 columns(Rob Herring)
> c)Moved DT binding file to bindings/net/wireless/(Rob Herring)
> d)Renamed "mwifiex,chip-gpio" to "marvell,wakeup-gpios"(Rob Herring/
> Arnd Bergmann)
> e)Replaced #ifdef with __maybe_unused(Arnd Bergmann)
>
> v5: a)Removed wildcards from compatible string(Arnd Bergmann)
> b)Prepared single patch for all binding changes(Rob Herring)
> c)Specified our node as a subnode of SDIO controller. With this approach,
> we
> don't need to register new platform driver. (Rob herring)
> ---
> .../bindings/net/wireless/marvell-sd8xxx.txt | 56
> ++++++++++++++++++++++
> 1 file changed, 56 insertions(+)
> create mode 100644
> Documentation/devicetree/bindings/net/wireless/marvell-sd8xxx.txt
>
> diff --git
> a/Documentation/devicetree/bindings/net/wireless/marvell-sd8xxx.txt
> b/Documentation/devicetree/bindings/net/wireless/marvell-sd8xxx.txt
> new file mode 100644
> index 0000000..c43d488
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/wireless/marvell-sd8xxx.txt
> @@ -0,0 +1,56 @@
> +Marvell 8897/8997 (sd8897/sd8997) SDIO devices
> +------
> +
> +This node provides properties for controlling the marvell sdio wireless
> device.
> +The node is expected to be specified as a child node to the SDIO controller
> that
> +connects the device to the system.
> +
> +Required properties:
> +
> + - compatible : should be one of the following:
> + * "marvell,sd8897"
> + * "marvell,sd8997"
> +
> +Optional properties:
> +
> + - marvell,caldata* : A series of properties with marvell,caldata prefix,
> + represent Calibration data downloaded to the device during
> + initialization. This is an array of unsigned values.
You need to list out the specific property names and size of the data.
> + - marvell,wakeup-pin : 'wakeuppin' is a wakeup pin number of wifi chip
> which will
> + be configured to firmware. firmware will wakeup host side
> use
> + the pin during suspend/resume stage.
> + - interrupt-parent: phandle of the parent interrupt controller
> + - interrupts : interrupt pin number to the cpu. driver will request an irq
> based on
> + this interrupt number. during system suspend, the irq will be
> enabled
> + as system wakeup source, so that the wifi chip can wakeup host
> + platform under certain condition. during system resume, the
> irq will
> + be disabled to make sure unnecessary interrupt is not received.
> +
> +Example:
> +
> +Tx power limit calibration data is configured in below example.
> +The calibration data is an array of unsigned values, the length
> +can vary between hw versions.
> +IRQ pin 38 is used as system wakeup source interrupt. wakeup pin 3 is
> configured
> +so that firmware can wakeup host using this device side pin.
> +
> +&mmc3 {
> + status = "okay";
> + vmmc-supply = <&wlan_en_reg>;
> + bus-width = <4>;
> + cap-power-off-card;
> + keep-power-in-suspend;
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> + mwifiex: mwifiex@3 {
The unit address and reg value don't match. IIRC, the correct value is
the SDIO function number.
> + compatible = "marvell,sd8897";
> + reg = <1>;
> + interrupt-parent = <&pio>;
> + interrupts = <38 IRQ_TYPE_LEVEL_LOW>;
> +
> + marvell,caldata_00_txpwrlimit_2g_cfg_set = /bits/ 8 <
> + 0x01 0x00 0x06 0x00 0x08 0x02 0x89 0x01>;
> + marvell,wakeup-pin = <3>;
> + };
> +};
> --
> 1.8.1.4
>
> --
> To unsubscribe from this list: send the line "unsubscribe devicetree" in
> the body of a message to [email protected]
> More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
