On 11/07/2016 03:54 AM, Bruno Antunes wrote:
On 4 November 2016 at 22:23, Ben Greear <gree...@candelatech.com> wrote:
The bug appears that vlan-tx-stripping is unconditionally enabled in
at least my firmware. I have re-compiled w/out that flag set, and it
appears
to work for me.
Please download this firmware, rename it firmware-2.bin, make sure you
remove/rename
any firmware-5.bin (etc) so mine will load, and see if that fixes your
problem.
Thanks for the fast reply but it only solves "half" the problem.
Now the connection between the AP and the Sta can be secure and the
driver doesn't need to be loaded in rawmode.
Unfortunatly the the throughput is still bad.
iperf3 -c 10.10.4.15
Connecting to host 10.10.4.15, port 5201
[ 4] local 10.10.4.16 port 44893 connected to 10.10.4.15 port 5201
[ ID] Interval Transfer Bandwidth Retr Cwnd
[ 4] 0.00-1.01 sec 42.4 KBytes 345 Kbits/sec 6 1.41 KBytes
[ 4] 1.01-2.01 sec 0.00 Bytes 0.00 bits/sec 1 1.41 KBytes
[ 4] 2.01-3.01 sec 0.00 Bytes 0.00 bits/sec 1 1.41 KBytes
[ 4] 3.01-4.01 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes
[ 4] 4.01-5.01 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes
[ 4] 5.01-6.01 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes
[ 4] 6.01-7.01 sec 0.00 Bytes 0.00 bits/sec 1 1.41 KBytes
[ 4] 7.01-8.01 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes
[ 4] 8.01-9.01 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes
[ 4] 9.01-10.01 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bandwidth Retr
[ 4] 0.00-10.01 sec 42.4 KBytes 34.7 Kbits/sec 9 sender
[ 4] 0.00-10.01 sec 0.00 Bytes 0.00 bits/sec receiver
You have a complex setup, so I think it would be best if you could break it into
simpler parts to test.
First, try just STA to AP, no vlans, and see if you get useful throughput.
Then try with VLANs
Then, try with WDS.
Then try with WDS and vlans.
In STA to AP mode with VLANs, it performed well for me.
Thanks,
Ben
iperf Done.
Please note that it is very likely you will have to use same MAC address
for the VLAN devices that the underlying station uses in order for this to
work.
Can you please elaborate more?
My setup is the folowing.
The connection between the AP and Sta is in WDS
For the moment all devices are in the same VLAN.
client1 --- SW1 ---- AP ...... Sta ---- SW2 --- client2
Thanks,
Bruno
https://www.candelatech.com/downloads/tmp/firmware-2-full-community.bin
Thanks,
Ben
Ben Greear <gree...@candelatech.com>
Candela Technologies Inc http://www.candelatech.com
--
Ben Greear <gree...@candelatech.com>
Candela Technologies Inc http://www.candelatech.com
