From: Igor Mitsyanko <[email protected]>
This patchset has a goal to make operational parameters (channel, BW,
HT/VHT capabilities) configuration possible for qtnfmac driver.
Basically the idea is to make driver level as thin as possible, and let
everything to be handled by userspace/nl80211 and wireless device itself.
Tested by trying various parameters combinations in hostapd.conf.
Set channel=36, bw=20, HT=0, VHT=0:
hw_mode=a
channel=36
Set channel=36, bw=20, HT=1, VHT=0:
ieee80211n=1
Set channel=36, bw=40 with secondary channel above, HT=1, VHT=0:
ieee80211n=1
ht_capab=[HT40+][SHORT-GI-20][SHORT-GI-40][MAX-AMSDU-7935]
Set channel=36, bw=40 with secondary channel below, HT=1, VHT=0:
channel=40
ieee80211n=1
ht_capab=[HT40-][SHORT-GI-20][SHORT-GI-40][MAX-AMSDU-7935]
Set channel=36, bw=40, HT=1, VHT=1:
ieee80211n=1
ht_capab=[HT40+][SHORT-GI-20][SHORT-GI-40][MAX-AMSDU-7935]
ieee80211ac=1
vht_capab=[SHORT-GI-80][MAX-MPDU-11454][MAX-A-MPDU-LEN-EXP-7][SU-BEAMFORMER][SU-BEAMFORMEE]
vht_oper_chwidth=0
Set channel=36, bw=80, HT=1, VHT=1:
ieee80211ac=1
vht_capab=[SHORT-GI-80][MAX-MPDU-11454][MAX-A-MPDU-LEN-EXP-7][SU-BEAMFORMER][SU-BEAMFORMEE]
vht_oper_chwidth=1
vht_oper_centr_freq_seg0_idx=42
Igor Mitsyanko (27):
qtnfmac: qlink: convert channel width from bitfiled to simple enum
qtnfmac: make "Channel change" event report full channel info
qtnfmac: retreive current channel info from EP
qtnfmac: do not cache AP settings in driver structures
qtnfmac: pass all AP settings to wireless card for processing
qtnfmac: pass full channel definition to device on start_ap command
qtnfmac: get rid of QTNF_STATE_AP_CONFIG
qtnfmac: get rid of QTNF_STATE_AP_START usage
qtnfmac: do not cache BSS state in per-VIF structure
qtnfmac: do not cache channel info from "connect" command
qtnfmac: make encryption info a part of "connect" command.
qtnfmac: let wifi card handle channel switch request to the same chan
qtnfmac: pass VIF info to SendChannel command
qtnfmac: do not cache CSA chandef info
qtnfmac: remove unused mac::status field
qtnfmac: stop using private driver info about current channel
qtnfmac: do not report channel changes until wiphy is registered
qtnfmac: use per-band HT/VHT info from wireless device
qtnfmac: initialize HT/VHT caps "can override" masks
qtnfmac: get rid of PHYMODE capabilities flags
qtnfmac: extend "IE set" TLV to include frame type info
qtnfmac: SCAN results: retreive frame type information from "IE set"
TLV
qtnfmac: convert "Append IEs" command to QTN_TLV_ID_IE_SET usage
qtnfmac: configure and start AP interface with a single command
nl80211: look for HT/VHT capabilities in beacon's tail
qtnfmac: include HTCAP and VHTCAP into config AP command
qtnfmac: pass all CONNECT cmd params to wireless card for processing
drivers/net/wireless/quantenna/qtnfmac/cfg80211.c | 234 ++--------
drivers/net/wireless/quantenna/qtnfmac/commands.c | 470 ++++++++++++++-------
drivers/net/wireless/quantenna/qtnfmac/commands.h | 11 +-
drivers/net/wireless/quantenna/qtnfmac/core.c | 3 +-
drivers/net/wireless/quantenna/qtnfmac/core.h | 35 +-
drivers/net/wireless/quantenna/qtnfmac/event.c | 134 +++---
drivers/net/wireless/quantenna/qtnfmac/qlink.h | 265 ++++++++----
.../net/wireless/quantenna/qtnfmac/qlink_util.c | 113 ++++-
.../net/wireless/quantenna/qtnfmac/qlink_util.h | 7 +
net/wireless/nl80211.c | 4 +-
10 files changed, 709 insertions(+), 567 deletions(-)
--
2.9.5
