On Tue, Oct 30, 2018 at 3:41 AM <[email protected]> wrote:
>
> On 2018-10-16 00:54, Rob Herring wrote:
> > On Thu, Oct 04, 2018 at 05:12:43PM +0530, Bhagavathi Perumal S wrote:
> >> This adds new dt entry ext-fem-name, it is used by ath10k driver
> >> to select correct timing parameters and configure it in target wifi
> >> hardware.
> >> The Front End Module(FEM) normally includes tx power amplifier(PA) and
> >> rx low noise amplifier(LNA). The default timing parameters like tx end
> >> to
> >> PA off timing values were fine tuned for internal FEM used in
> >> reference
> >> design. And these timing values can not be same if ODM modifies
> >> hardware
> >> design with different external FEM. This DT entry helps to choose
> >> correct
> >> timing values in driver if different external FEM hardware used.
> >
> > 'dt-bindings: net: ath10k: ...' for the subject please.
> Sure, I will change and send v2 patch.
>
> >
> >>
> >> Signed-off-by: Bhagavathi Perumal S <[email protected]>
> >> ---
> >> .../bindings/net/wireless/qcom,ath10k.txt | 22
> >> ++++++++++++++++++++++
> >> 1 file changed, 22 insertions(+)
> >>
> >> diff --git
> >> a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt
> >> b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt
> >> index 7fd4e8c..fbaf309 100644
> >> --- a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt
> >> +++ b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt
> >> @@ -56,6 +56,7 @@ Optional properties:
> >> the length can vary between hw versions.
> >> - <supply-name>-supply: handle to the regulator device tree node
> >> optional "supply-name" is "vdd-0.8-cx-mx".
> >> +- ext-fem-name: name of external front end module used.
> >
> > What are valid names? What if the OS doesn't recognize the name?
> > Perhaps
> Some valid FEM devices are "microsemi-lx5586", "sky85703-11" and
> "sky85803" etc.
> Currently driver accepts only "microsemi-lx5586", Since this FEM
> requires different timing settings,
Assuming you keep this, then you need to enumerate what are valid
values in the binding. Otherwise, 'ext-fem-name = "rob"' is valid.
> And it can be extended for other FEM devices in future.
> If OS doesn't recognize the name, it uses predefined default timing
> settings.
>
> > this should be a compatible string for the particular module instead?
> > Then it could cover any differences, not just the FEM.
> >
> No, it is specific to FEM device.
You will be better off having either a specific compatible string or
using VID/PID as this is a PCI device. Then you can handle other
differences you may find between h/w versions without a DT change.
> >>
> >> Example (to supply the calibration data alone):
> >>
> >> @@ -150,3 +151,24 @@ wifi@18000000 {
> >> <0 141 0 /* CE11 */ >;
> >> vdd-0.8-cx-mx-supply = <&pm8998_l5>;
> >> };
> >> +
> >> +Example (to supply the external front end module name):
> >> +
> >> +In this example, the front end module is defined as a property of the
> >> ath10k
> >> +device node.
> >
> > Really need a whole new example for 1 property?
> Will add this property in existing example.
>
> >
> >> +
> >> +pci {
> >> + pcie@0 {
> >> + reg = <0 0 0 0 0>;
> >> + #interrupt-cells = <1>;
> >> + #size-cells = <2>;
> >> + #address-cells = <3>;
> >> + device_type = "pci";
> >> +
> >> + ath10k@0,0 {
> >
> > wifi@0,0
> Added in ath10k@0,0 to make consistent with existing property
> "qcom,ath10k-calibration-data" below,
> "
I don't see how that matters.
> pci {
> pcie@0 {
> reg = <0 0 0 0 0>;
> #interrupt-cells = <1>;
> #size-cells = <2>;
> #address-cells = <3>;
> device_type = "pci";
>
> ath10k@0,0 {
> reg = <0 0 0 0 0>;
> device_type = "pci";
> qcom,ath10k-calibration-data = [ 01 02 03 ... ];
> };
> };
> };
> "
>
> If wifi@0,0 is preferable, then I will add new entry "wifi@0,0" and add
> ext-fem-name into it.
Node names are supposed to reflect the class of device, not the model.
See the DT spec for a list.
>
> >
> >> + reg = <0 0 0 0 0>;
> >> + device_type = "pci";
Also, this is wrong. Only PCI bridges should have this property. dtc
will give you a warning on this.
> >> + ext-fem-name = "microsemi-lx5586";
> >> + };
> >> + };
> >> +};
> >> --
> >> 1.9.1
> >>
>
> Thanks, Sorry for the delayed response,
> Bhagavathi Perumal S.
