Hi again,

currently such magic is unavailable, I have some internal demo, which scan
for a coordinator and connect to it by pressing on-board button. But it's a
raw demo-draft only. This moment I have no free time to finish this tool :(

Thank you,
Alexander

2011/7/6 voice <voice.s...@gmail.com>

> **
> Hi Alexander,
>   With your hint, it works my board.
>   Thank you very much!
>
>   BTW, is there any good method to configure the zigbee?
>
>   For my instance, I use one script to combine the command together as
> following:
>   iz add wpan-phy0
>   ip link set wpan0 address <address>
>   ifconfig wpan0 up
>   iz scan ...
>   iz attach ...
>
>   So, if there good method to configure the zigbee like configure the WIFI,
> just need scan and attach?
>
>   Thanks again!
>
>
>
> 2011-07-06
> ------------------------------
>  voice
> ------------------------------
> *发件人:* Alexander Smirnov
> *发送时间:* 2011-07-06  14:34:57
> *收件人:* voice
> *抄送:* linux-zigbee-devel
> *主题:* Re: [Linux-zigbee-devel] iz scan issue
>  Hi,
>
> thank you for the interest to this project!
>
> The 'channels' argument to iz command is a bit mask (not a number).
> Currently supported the following mask: 0x7fff800 (channels from 12 to 31).
>
>
> So below is my output:
>
> root@at91sam9g20ek:~/bin# iz scan wpan0 active 800 1
> Found beacon:
>         Short addr: 1
>         PAN id: 1911
>
> root@at91sam9g20ek:~/bin# iz scan wpan0 active 7fff800 1
> Found beacon:
>         Short addr: 1
>         PAN id: 1911
> Finished active (beacons) scan...
>
> NOTE: that PAN id is decimal number in this output.
>
> Thank you,
> Alexander
>
> 2011/7/6 voice <voice.s...@gmail.com>
>
>> **
>> Hi All,
>>   I use the Linux kernel which include zigbee stack from Linux-zigbee
>> project. Using the 88RF231 hardware with at91sam9g20ek board.
>>   It can configure the device successfully and send data between two
>> devices.
>>
>>   But, If I use the iz scan command it will git the following error
>> information. Any advices for it?
>> --------------------------------------------------------------
>> root@at91sam9g20ek_2mmc:~# iz scan wpan0 active 15 10
>> Scan failed: e8
>> Started active (beacons) scan...
>> Receive failed: Netlink Error (errno = Invalid argument)
>> ---------------------------------------------------------------
>>
>>
>> 2011-07-06
>> ------------------------------
>> voice
>>
>>
>> ------------------------------------------------------------------------------
>> All of the data generated in your IT infrastructure is seriously valuable.
>> Why? It contains a definitive record of application performance, security
>> threats, fraudulent activity, and more. Splunk takes this data and makes
>> sense of it. IT sense. And common sense.
>> http://p.sf.net/sfu/splunk-d2d-c2
>> _______________________________________________
>> Linux-zigbee-devel mailing list
>> Linux-zigbee-devel@lists.sourceforge.net
>> https://lists.sourceforge.net/lists/listinfo/linux-zigbee-devel
>>
>>
>
------------------------------------------------------------------------------
All of the data generated in your IT infrastructure is seriously valuable.
Why? It contains a definitive record of application performance, security 
threats, fraudulent activity, and more. Splunk takes this data and makes 
sense of it. IT sense. And common sense.
http://p.sf.net/sfu/splunk-d2d-c2
_______________________________________________
Linux-zigbee-devel mailing list
Linux-zigbee-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/linux-zigbee-devel

Reply via email to