Hi, Apologize for leaving out version information. I am using kernel: Linux beaglebone 3.8.13-bone50 #1 SMP Tue May 13 13:24:52 UTC 2014 armv7l GNU/Linux
I had to compile the libn1 and tools to get this far since there was a crash in iz add. These are the versions that I downloaded and compiled. drwxr-xr-x 11 debian admin 4096 Oct 28 2014 libnl-3.2.25 drwxr-xr-x 11 debian admin 4096 Oct 28 2014 lowpan-tools-0.3.1 and just to confirm that they updated: root@beaglebone:~# iz --version iz: /lib/arm-linux-gnueabihf/libnl-genl-3.so.200: no version information available (required by iz) iz: /lib/arm-linux-gnueabihf/libnl-3.so.200: no version information available (required by iz) iz 0.3.1 Appreciate your help Alex. Right now I’m under water as well so I understand your pain. Let me know if I can help in anyway Ad > On Nov 1, 2014, at 2:47 AM, Alexander Aring <alex.ar...@gmail.com > <mailto:alex.ar...@gmail.com>> wrote: > > Hi, > > On Sat, Nov 01, 2014 at 02:01:55AM -0600, Dr. Aditya Nagrath PhD wrote: >> I am trying to get a MRF24j40 on a BeagleBone Black to talk to an arduino >> with a mrf24j40. I have successfully communicated arduino to arduino but as >> of yet have not been able to receive the packets being sent out on the BBB. >> >> The setup: I have GPIO_13 going to reset (pin 2), GPIO_14 going to wake >> (pin 3) and GPIO_29 going to interrupt (4). The 3.3v is going to vin on 10 >> and ground on pin 1. I am using SPI1 with the HDMI ports disabled. D0 is >> mapping to pin 7 (SDO) and D1 is mapping to pin 5 (SDI), P9.31 the clock >> goes to pin 6 and P9.28 goes to pin 8. >> >> I have been able to log into the BBB via ssh. I then load the cape for the >> MRF24j40 using the echo to /sys/devices/bone_capemgr.9/slots >> >> This appears to load the driver properly. >> >> I have then been able to do: >> >> iz listphy >> iz: /lib/arm-linux-gnueabihf/libnl-genl-3.so.200: no version information >> available (required by iz) >> iz: /lib/arm-linux-gnueabihf/libnl-3.so.200: no version information >> available (required by iz) >> wpan-phy0 IEEE 802.15.4 PHY object >> page: 0 channel: n/a >> channels on page 0: 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 >> >> iz add wpan- >> iz: /lib/arm-linux-gnueabihf/libnl-genl-3.so.200: no version information >> available (required by iz) >> iz: /lib/arm-linux-gnueabihf/libnl-3.so.200: no version information >> available (required by iz) >> Registered new device ('wpan0') on phy wpan-phy0 >> >> I decided to set all my addresses to simple things on the arduino side in >> case there is some sort of endian problem so the pan id is 0, the address of >> the sender is 0 and it sends the data to 1, thus I try to set the beaglebone >> to pan id 0, address 1 with a destination address of 0. >> >> root@beaglebone:~# iz set wpan0 0 1 12 >> iz: /lib/arm-linux-gnueabihf/libnl-genl-3.so.200: no version information >> available (required by iz) >> iz: /lib/arm-linux-gnueabihf/libnl-3.so.200: no version information >> available (required by iz) >> ifconfig wpan0 up >> >> Then I run >> izchat 0 1 0 >> >> I get nothing on the BBB side even though the other side is constantly >> transmitting... and when I type into izchat, I do not receive anything on >> the other side. >> >> Any help here would be appreciated... I just want to see some data before I >> start coding. Like I said, this has been tested arduino to arduino and does >> not have problems. > > Mailinglist changed to [0]. > > Please let me know which kernel, libnl3 and lowpan-tools version do you > use. > > Also I need to notice you that I am working on a big rework. With new > userspace tools, etc... I need some time to bring it mainline. The bring > it mainline thing is currently in progress. > > I am very busy right now. > > - Alex > > [0] http://vger.kernel.org/vger-lists.html#linux-wpan > <http://vger.kernel.org/vger-lists.html#linux-wpan>
------------------------------------------------------------------------------
_______________________________________________ Linux-zigbee-devel mailing list Linux-zigbee-devel@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/linux-zigbee-devel
