Am Sonntag 20 September 2009 schrieb Flo: > Wo genau ist dein problem? Ich sehe da dein kernel eine USB Platte > findet und die als /dev/sdc zeigt - da scheint aber keine partition > drauf zu sein so wie ich das interpretiere - Aber wenn du eine > Antwort willst solltest du eine konkrete Frage stellen
Hallo, sorry, ich war etwas kurz angebunden - und wollte eigentlich zunächst spontane Hinweise auf typische Fehler hören, die bei der 1. Verwendung eines solchen Adapters gemacht werden. Ich bin nun etwas weiter: 1. IDE-Platte auf "Master" jumpern! 2. Erst Platte hochfahren (Strom!), dann an USB-Port des PC anschließen. Natürlich ist auf der Platte etwas drauf, und ich konnte auch schon die ersten Partitionen durchsehen. Nur ist das Ganze offenbar nicht ganz stabil - vielleicht wird ja jemand aus diesen syslog-Zeilen schlau: >usb-storage: device found at 15 >usb-storage: waiting for device to settle before scanning >usb-storage: device scan complete >usb 1-1.3: reset high speed USB device using ehci_hcd and address 15 >usb 1-1.3: reset high speed USB device using ehci_hcd and address 15 >scsi 125:0:0:0: Direct-Access Maxtor 3 4098H4 14Y0 PQ: 0 > ANSI: 2 CCS sd 125:0:0:0: Attached scsi generic sg4 type 0 >sd 125:0:0:0: [sdc] 80043264 512-byte hardware sectors: (40.9 GB/38.1 > GiB) sd 125:0:0:0: [sdc] Write Protect is off >sd 125:0:0:0: [sdc] Mode Sense: 00 38 00 00 >sd 125:0:0:0: [sdc] Assuming drive cache: write through >sd 125:0:0:0: [sdc] Assuming drive cache: write through > sdc: sdc1 sdc2 < sdc5 sdc6 sdc7 sdc8 sdc9 sdc10 sdc11 sdc12 sdc13 > sdc14 sdc15 sdc16<6>sd 125:0:0:0: [sdc] Unhandled error code sd > 125:0:0:0: [sdc] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK > end_request: I/O error, dev sdc, sector 79521744 >Buffer I/O error on device sdc, logical block 9940218 >sd 125:0:0:0: [sdc] Unhandled error code >sd 125:0:0:0: [sdc] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK >end_request: I/O error, dev sdc, sector 79521744 >Buffer I/O error on device sdc, logical block 9940218 >... > sdc: sdc1 sdc2 < sdc5 sdc6 sdc7 sdc8 sdc9 sdc10 sdc11 sdc12 sdc13 > sdc14 sdc15 sdc16 sdc17 > sd 126:0:0:0: [sdc] Attached SCSI disk >sd 126:0:0:0: [sdc] Unhandled error code >sd 126:0:0:0: [sdc] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK >end_request: I/O error, dev sdc, sector 0 >Buffer I/O error on device sdc, logical block 0 >Buffer I/O error on device sdc, logical block 1 >Buffer I/O error on device sdc, logical block 2 >Buffer I/O error on device sdc, logical block 3 >sd 126:0:0:0: [sdc] Unhandled error code >sd 126:0:0:0: [sdc] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK >end_request: I/O error, dev sdc, sector 0 >Buffer I/O error on device sdc, logical block 0 Mal sehen, ob SMART via USB funktioniert, die Platte hat evtl. eine Macke... Gute Nacht Ralf -- Linux mailing list [email protected] subscribe/unsubscribe: http://lug-owl.de/mailman/listinfo/linux Hinweise zur Nutzung: http://www.lug-owl.de/Mailingliste/hints.epo
