You can comment out dir /drivers/broadcom/tg3 too. Current Etherboot has problem with NIC is S2850. I forget the chip model.
So I use one add on card to do network booting. (intel eepro100) Regards YH -----Original Message----- From: Sagiv Yefet [mailto:[EMAIL PROTECTED] Sent: Wednesday, September 15, 2004 4:53 AM To: YhLu Cc: Stefan Reinauer; [EMAIL PROTECTED] Subject: RE: (fwd) RE: building romimage for tyan s2850 mainboard [EMAIL PROTECTED] How can I had the broadcom NIC ? When I comment out this in Config.lb (mainboard)? dir /drivers/broadcom/tg3_ipmi the buildtarget utility says it is not in the Sourcetree. When I change this line to be: dir /drivers/broadcom/tg3 (existing dir in the Sourcetree) there is a make error. I tried it with gcc-3.3.1 and gcc-3.3.2 I have binutils 2.15. Did you ever succeed to build an image supporting broadcom NIC ? Regards, Sagiv -----Original Message----- From: YhLu [mailto:[EMAIL PROTECTED] Sent: Tuesday, September 14, 2004 6:55 PM To: Stefan Reinauer; [EMAIL PROTECTED]; Sagiv Yefet Subject: RE: (fwd) RE: building romimage for tyan s2850 mainboard [EMAIL PROTECTED] Sagiv, I just sent you tar ball of my source code before I added S2895 and S2735 support. Please check it out. Regards YH -----Original Message----- From: Stefan Reinauer [mailto:[EMAIL PROTECTED] Sent: Tuesday, September 14, 2004 7:29 AM To: [EMAIL PROTECTED]; Sagiv Yefet Subject: (fwd) RE: building romimage for tyan s2850 mainboard [EMAIL PROTECTED] 1) Please Cc the mailing list, there are many people who might help you quicker/better than I do. 2) I don't understand your first question at all. 3) "invalid CMOS LB checksum" Means that the CMOS is not valid for LinuxBIOS. Probably because you had a different firmware running before LinuxBIOS in that machine. This error should go away automatically after rebooting. Stefan ----- Forwarded message from Sagiv Yefet <[EMAIL PROTECTED]> ----- Date: Tue, 14 Sep 2004 16:41:46 +0200 From: "Sagiv Yefet" <[EMAIL PROTECTED]> To: "Stefan Reinauer" <[EMAIL PROTECTED]> Subject: RE: building romimage for tyan s2850 mainboard I comment out the: #dir /drivers/ati/ragexl -- video which pci line in the southbridge it relate to? southbridge amd/amd8111 "amd8111" link 0 pci 0:0.0 pci 0:1.0 on pci 0:1.1 on pci 0:1.2 on pci 0:1.3 on pci 0:1.5 off pci 0:1.6 off pci 1:0.0 on pci 1:0.1 on pci 1:0.2 off pci 1:1.0 off end what is this ERROR means ? invalid CMOS LB checksum Sagiv. -----Original Message----- From: Stefan Reinauer [mailto:[EMAIL PROTECTED] Sent: Tuesday, September 14, 2004 12:57 PM To: Sagiv Yefet Cc: [EMAIL PROTECTED] Subject: Re: building romimage for tyan s2850 mainboard * Sagiv Yefet <[EMAIL PROTECTED]> [040914 12:43]: > Thanks, it worked. > > There are 2 errors: > 1. ERROR - could not find PCI 1:03.0, using defaults This looks like an error in the mptable creation, but I am not sure without the context here. > 2. ERROR: PNP: 002e.b 70 not allocated > in Config.lb: 002e.b = HW monitor No idea. I always kind of guessed when fiddling with PnP configuration. > what does it means? Can anyone on the list give some details here? Stefan ----- End forwarded message ----- _______________________________________________ Linuxbios mailing list [EMAIL PROTECTED] http://www.clustermatic.org/mailman/listinfo/linuxbios _______________________________________________ Linuxbios mailing list [EMAIL PROTECTED] http://www.clustermatic.org/mailman/listinfo/linuxbios
