Hello,
Finally my linuxbios bring up the target board.
capture5.txt is booting log.
But most of device on the target board are not work.
Such as BCM5704 under PCI-X bridge.
If I try to load "tg3" module into the kernel, I got error message like this,
[EMAIL PROTECTED] ~]# modprobe tg3
PCI: No IRQ known for interrupt pin A of device 0000:03:04.0. Please try using pci=biosirq.
PCI: No IRQ known for interrupt pin B of device 0000:03:04.1. Please try using pci=biosirq.
PCI: No IRQ known for interrupt pin A of device 0000:03:04.0. Please try using pci=biosirq.
PCI: No IRQ known for interrupt pin B of device 0000:03:04.1. Please try using pci=biosirq.
How to assign an IRQ for each device ??
2006/5/12, Stefan Reinauer <[EMAIL PROTECTED]>:
* Vincente Tsou <[EMAIL PROTECTED]> [060512 06:22]:
> Dear Lu and Stefan,
>
> Thank you very much for your reply.
>
> But I can't find the inherent_ht.c in my LinuxBios source tree.
Yinghai is talking about src/northbridge/amd/amdk8/incoherent_ht.c
You need to try commenting out the lines I sent in the last mail from
src/northbridge/amd/amdk8/resourcemap.c
Stefan
--
coresystems GmbH • Brahmsstr. 16 • D-79104 Freiburg i. Br.
Tel.: +49 761 7668825 • Fax: +49 761 7664613
Email: [EMAIL PROTECTED] • http://www.coresystems.de/
--
Best Regards,
Vincente Tsou
Engineer
R/D, S/W Dept.
NEXCOM International Co.
Tel: 886-2-82280606 Ext. 3205
Fax: 886-2-82280506
E-mail: [EMAIL PROTECTED]
Web: http://www.nexcom.com.tw/
LinuxBIOS-1.1.8h412_Fallback Mon Jun 19 15:02:16 CST 2006 starting... 01 nodes initialized. SBLink=01 NC node|link=01 ht reset - LinuxBIOS-1.1.8h412_Fallback Mon Jun 19 15:02:16 CST 2006 starting... 01 nodes initialized. SBLink=01 NC node|link=01 Ram1.00 Ram2.00 Ram3 Initializing memory: done Ram4 v_esp=000cfd54 testx = 5a5a5a5a Copying data from cache to ram -- switching to use ram as stack... Done testx = 5a5a5a5a Disabling cache as ram now Clearing initial memory region: Done Copying LinuxBIOS to ram. src=fffe0000 dst=00004000 linxbios_ram.bin length = 0001746c Jumping to LinuxBIOS. LinuxBIOS-1.1.8h412_Fallback Mon Jun 19 15:02:16 CST 2006 booting... Enumerating buses... PCI_DOMAIN: 0000 enabled APIC_CLUSTER: 0 enabled PCI: pci_scan_bus for bus 0 PCI: 00:18.0 [1022/1100] enabled PCI: 00:18.1 [1022/1101] enabled PCI: 00:18.2 [1022/1102] enabled PCI: 00:18.3 [1022/1103] enabled Disabling static device: PCI: 00:19.0 Disabling static device: PCI: 00:19.1 Disabling static device: PCI: 00:19.2 Disabling static device: PCI: 00:19.3 PCI: 01:00.0 [1022/7450] enabled PCI: 01:01.0 [1022/7450] enabled next_unitid: 0003 PCI: 01:00.0 [1022/7460] enabled PCI: 01:03.0 [1022/7460] enabled next_unitid: 0007 PCI: pci_scan_bus for bus 1 PCI: 01:01.0 [1022/7450] enabled PCI: 01:01.1 [1022/7451] enabled PCI: 01:02.0 [1022/7450] enabled PCI: 01:02.1 [1022/7451] enabled PCI: 01:03.0 [1022/7460] enabled PCI: 01:04.0 [1022/7468] enabled PCI: 01:04.1 [1022/7469] enabled PCI: 01:04.2 [1022/746a] enabled PCI: 01:04.3 [1022/746b] enabled PCI: pci_scan_bus for bus 2 PCI: pci_scan_bus returning with max=02 PCI: 02: Conventional PCI PCI: pci_scan_bus for bus 3 PCI: 03:04.0 [14e4/16a8] enabled PCI: 03:04.1 [14e4/16a8] enabled PCI: pci_scan_bus returning with max=03 PCI: 03: 133MHz PCI-X PCI: pci_scan_bus for bus 4 PCI: 04:00.0 [1022/7464] enabled PCI: 04:00.1 [1022/7464] enabled USB2 disabled. PCI: 04:00.2 [1022/7463] disabled PCI: 04:02.0 [1002/4752] enabled PCI: 04:04.0 [8086/1229] enabled PCI: pci_scan_bus returning with max=04 PNP: 002e.0 disabled PNP: 002e.1 disabled PNP: 002e.2 enabled PNP: 002e.3 enabled PNP: 002e.5 enabled PNP: 002e.6 disabled PNP: 002e.7 disabled PNP: 002e.8 disabled PNP: 002e.9 disabled PNP: 002e.a disabled PNP: 002e.b enabled PCI: pci_scan_bus returning with max=04 PCI: pci_scan_bus returning with max=04 PCI: 00:18.3 siblings=0 CPU: APIC: 00 enabled done Allocating resources... Reading resources... PCI: 01:02.0 1c <- [0x00fffff000 - 0x00ffffefff] bus 3 io PCI: 01:02.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 3 prefmem PCI: 01:03.0 24 <- [0x00fff00000 - 0x00ffefffff] bus 4 prefmem Done reading resources. Setting resources... PCI: 00:18.0 1a1 <- [0x00fd300000 - 0x00fd2fffff] prefmem <node 0 link 1> PCI: 00:18.0 1a9 <- [0x00fc000000 - 0x00fd2fffff] mem <node 0 link 1> PCI: 00:18.0 1d9 <- [0x0000001000 - 0x0000002fff] io <node 0 link 1> PCI: 01:01.1 10 <- [0x00fd200000 - 0x00fd200fff] mem64 PCI: 01:02.0 20 <- [0x00fd100000 - 0x00fd1fffff] bus 3 mem PCI: 03:04.0 10 <- [0x00fd100000 - 0x00fd10ffff] mem64 PCI: 03:04.0 18 <- [0x00fd110000 - 0x00fd11ffff] mem64 PCI: 03:04.1 10 <- [0x00fd120000 - 0x00fd12ffff] mem64 PCI: 03:04.1 18 <- [0x00fd130000 - 0x00fd13ffff] mem64 PCI: 01:02.1 10 <- [0x00fd201000 - 0x00fd201fff] mem64 PCI: 01:03.0 1c <- [0x0000001000 - 0x0000001fff] bus 4 io PCI: 01:03.0 20 <- [0x00fc000000 - 0x00fd0fffff] bus 4 mem PCI: 04:00.0 10 <- [0x00fd050000 - 0x00fd050fff] mem PCI: 04:00.1 10 <- [0x00fd051000 - 0x00fd051fff] mem PCI: 04:02.0 10 <- [0x00fc000000 - 0x00fcffffff] mem PCI: 04:02.0 14 <- [0x0000001000 - 0x00000010ff] io PCI: 04:02.0 18 <- [0x00fd052000 - 0x00fd052fff] mem PCI: 04:02.0 30 <- [0x00fd000000 - 0x00fd01ffff] romem PCI: 04:04.0 10 <- [0x00fd053000 - 0x00fd053fff] mem PCI: 04:04.0 14 <- [0x0000001400 - 0x000000143f] io PCI: 04:04.0 18 <- [0x00fd020000 - 0x00fd03ffff] mem PCI: 04:04.0 30 <- [0x00fd040000 - 0x00fd04ffff] romem PNP: 002e.2 60 <- [0x00000003f8 - 0x00000003ff] io PNP: 002e.2 70 <- [0x0000000004 - 0x0000000004] irq PNP: 002e.3 60 <- [0x00000002f8 - 0x00000002ff] io PNP: 002e.3 70 <- [0x0000000003 - 0x0000000003] irq PNP: 002e.5 60 <- [0x0000000060 - 0x0000000060] io PNP: 002e.5 62 <- [0x0000000064 - 0x0000000064] io PNP: 002e.5 70 <- [0x0000000001 - 0x0000000001] irq PNP: 002e.5 72 <- [0x000000000c - 0x000000000c] irq PNP: 002e.b 60 <- [0x0000000290 - 0x0000000297] io PNP: 002e.b 70 <- [0x0000000005 - 0x0000000005] irq PCI: 01:04.1 20 <- [0x0000002420 - 0x000000242f] io PCI: 01:04.2 10 <- [0x0000002400 - 0x000000241f] io PCI: 01:04.3 58 <- [0x0000002000 - 0x00000020ff] io PCI: 00:18.3 94 <- [0x00f8000000 - 0x00fbffffff] mem <gart> Done setting resources. Done allocating resources. Enabling resources... PCI: 00:18.0 cmd <- 140 PCI: 01:01.1 subsystem <- 00/00 PCI: 01:01.1 cmd <- 146 PCI: 01:02.0 bridge ctrl <- 0003 PCI: 01:02.0 cmd <- 146 PCI: 03:04.0 subsystem <- 00/00 PCI: 03:04.0 cmd <- 142 PCI: 03:04.1 subsystem <- 00/00 PCI: 03:04.1 cmd <- 142 PCI: 01:02.1 subsystem <- 00/00 PCI: 01:02.1 cmd <- 146 PCI: 01:03.0 bridge ctrl <- 0003 PCI: 01:03.0 cmd <- 147 PCI: 04:00.0 subsystem <- 00/00 PCI: 04:00.0 cmd <- 142 PCI: 04:00.1 subsystem <- 00/00 PCI: 04:00.1 cmd <- 142 PCI: 04:02.0 cmd <- 1c3 PCI: 04:04.0 cmd <- 143 PCI: 01:04.0 subsystem <- 00/00 PCI: 01:04.0 cmd <- 14f w83627hf hwm smbus enabled PCI: 01:04.1 subsystem <- 00/00 PCI: 01:04.1 cmd <- 141 PCI: 01:04.2 subsystem <- 00/00 PCI: 01:04.2 cmd <- 141 PCI: 01:04.3 subsystem <- 00/00 PCI: 01:04.3 cmd <- 141 PCI: 00:18.1 subsystem <- 00/00 PCI: 00:18.1 cmd <- 140 PCI: 00:18.2 subsystem <- 00/00 PCI: 00:18.2 cmd <- 140 PCI: 00:18.3 cmd <- 140 done. Initializing devices... Root Device init PCI: 00:18.0 init PCI: 01:02.0 init PCI: 03:04.0 init PCI: 03:04.1 init PCI: 01:03.0 init PCI: 01:04.0 init amd8111: ioapic bsp_apicid = 00 RTC Init Invalid CMOS LB checksum enabling HPET @0xfed00000 PNP: 002e.2 init PNP: 002e.3 init PNP: 002e.5 init PNP: 002e.b init PCI: 01:04.1 init IDE1 IDE0 PCI: 01:04.3 init set power on after power fail PCI: 00:18.1 init PCI: 00:18.2 init PCI: 00:18.3 init NB: Function 3 Misc Control.. done. APIC_CLUSTER: 0 init Initializing CPU #0 CPU: vendor AMD device f5a Enabling cache Setting fixed MTRRs(0-88) type: UC Setting fixed MTRRs(0-16) Type: WB, RdMEM, WrMEM Setting fixed MTRRs(24-88) Type: WB, RdMEM, WrMEM DONE fixed MTRRs Setting variable MTRR 0, base: 0MB, range: 512MB, type WB DONE variable MTRRs Clear out the extra MTRR's MTRR check Fixed MTRRs : Enabled Variable MTRRs: Enabled microcode: equivalent processor rev id = 0x004a, patch id = 0x00000000 microcode: patch id that want to apply= 0x00000047 microcode: updated to patch id = 0x00000047 success Setting up local apic... apic_id: 0 done. Clearing memory 2048K - 524288K: ------- done CPU #0 Initialized APIC delivery error (4). CPU 1 would not start! CPU 1 did not initialize! All AP CPUs stopped PCI: 04:02.0 init PCI: 04:04.0 init Devices initialized Writing IRQ routing tables to 0xf0000...done. Wrote the mp table end at: 00000020 - 000001b8 Moving GDT to 0x500...ok Wrote linuxbios table at: 00000530 - 00000dcc checksum a17 Welcome to elfboot, the open sourced starter. January 2002, Eric Biederman. Version 1.3 rom_stream: 0xfffc0000 - 0xfffdffff Found ELF candiate at offset 0 Loading Etherboot version: 5.2.6 Dropping non PT_LOAD segment New segment addr 0x20000 size 0x6469a offset 0xb0 filesize 0xd0cd (cleaned up) New segment addr 0x20000 size 0x6469a offset 0xb0 filesize 0xd0cd Loading Segment: addr: 0x000000001ffa4000 memsz: 0x0000000000020000 filesz: 0x000000000000d0cd Clearing Segment: addr: 0x000000001ffb10cd memsz: 0x0000000000012f33 Loading Segment: addr: 0x0000000000040000 memsz: 0x000000000004469a filesz: 0x0000000000000000 Clearing Segment: addr: 0x0000000000040000 memsz: 0x000000000004469a Jumping to boot code at 0x20000 ROM segment 0x0000 length 0x0000 reloc 0x00020000 CPU 2281 Mhz Etherboot 5.2.6 (GPL) http://etherboot.org Tagged ELF for [TG3][FILO] Relocating _text from: [0002d0d0,00086240) to [1fea6e90,1ff00000) Boot from (N)etwork (D)isk or (Q)uit? D Probing pci disk... [FILO]FILO version 0.4.1 ([EMAIL PROTECTED]) Wed May 3 15:16:34 CST 2006 Press <Enter> for default boot, or <Esc> for boot prompt... 2 1 timed out boot: hda1:/boot/vmlinuz initrd=/boot/initrd noacpi ro root=/dev/hda1 console=tty0 console=ttyS0,115200 hda: LBA: Maxtor 6Y080P0 Mounted ext2fs Found Linux version 2.6.9-1.667 ([EMAIL PROTECTED]) #1 Tue Nov 2 14:41:25 EST 2004 bzImage. Loading kernel... ok Loading initrd... ok Jumping to entry point... Linux version 2.6.9-1.667 ([EMAIL PROTECTED]) (gcc version 3.4.2 20041017 (Red Hat 3.4.2-6.fc3)) #1 Tue Nov 2 14:41:25 EST 2004 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 0000000000000e34 type 16 BIOS-e820: 0000000000000e34 - 00000000000a0000 (usable) BIOS-e820: 00000000000f0000 - 00000000000f0400 type 16 BIOS-e820: 0000000000100000 - 0000000020000000 (usable) 0MB HIGHMEM available. 512MB LOWMEM available. zapping low mappings. DMI not present. ACPI: Unable to locate RSDP Built 1 zonelists Kernel command line: noacpi ro root=/dev/hda1 console=tty0 console=ttyS0,115200 mapped 4G/4G trampoline to ffff4000. Initializing CPU#0 CPU 0 irqstacks, hard=023d5000 soft=023d4000 PID hash table entries: 4096 (order: 12, 65536 bytes) Detected 2205.406 MHz processor. Using tsc for high-res timesource Console: colour dummy device 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 515148k/524288k available (2068k kernel code, 8584k reserved, 647k data, 144k init, 0k highmem) Security Scaffold v1.0.0 initialized SELinux: Initializing. SELinux: Starting in permissive mode There is already a security framework initialized, register_security failed. selinux_register_security: Registering secondary module capability Capability LSM initialized as secondary Mount-cache hash table entries: 512 (order: 0, 4096 bytes) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: AMD 02/05 stepping 0a Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. checking if image is initramfs... it is Freeing initrd memory: 386k freed NET: Registered protocol family 16 PCI: Using configuration type 1 mtrr: v2.0 (20020519) ACPI: Subsystem revision 20040816 ACPI: Interpreter disabled. Linux Plug and Play Support v0.97 (c) Adam Belay usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Probing PCI hardware PCI: Probing PCI hardware (bus 00) PCI: Unable to handle 64-bit address space for PCI: Discovered primary peer bus 01 [IRQ] PCI: Using IRQ router default [1022/7468] at 0000:01:04.0 PCI: IRQ 0 for device 0000:01:04.2 doesn't match PIRQ mask - try pci=usepirqmask apm: BIOS not found. audit: initializing netlink socket (disabled) audit(1009857017.468:0): initialized Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) SELinux: Registering netfilter hooks Initializing Cryptographic API ksign: Installing public key data Loading keyring - Added public key 6ECDA687281A73E5 - key was been created 89567280 seconds in future - User ID: Red Hat, Inc. (Kernel Module GPG key) pci_hotplug: PCI Hot Plug PCI Core version: 0.5 vesafb: probe of vesafb0 failed with error -6 isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Real Time Clock Driver v1.12 Linux agpgart interface v0.100 (c) Dave Jones serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled ÿttyS0 at I/O 0x3f8 (irq = 4) is a 16550A ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx AMD8111: IDE controller at PCI slot 0000:01:04.1 AMD8111: chipset revision 3 AMD8111: not 100% native mode: will probe irqs later AMD8111: 0000:01:04.1 (rev 03) UDMA133 controller ide0: BM-DMA at 0x2420-0x2427, BIOS settings: hda:pio, hdb:pio ide1: BM-DMA at 0x2428-0x242f, BIOS settings: hdc:pio, hdd:pio hda: Maxtor 6Y080P0, ATA DISK drive Using cfq io scheduler ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hda: max request size: 128KiB hda: 160086528 sectors (81964 MB) w/7936KiB Cache, CHS=65535/16/63, UDMA(133) hda:hda: dma_intr: status=0x51 { DriveReady SeekComplete Error } hda: dma_intr: error=0x84 { DriveStatusError BadCRC } ide: failed opcode was: unknown hda: dma_intr: status=0x51 { DriveReady SeekComplete Error } hda: dma_intr: error=0x84 { DriveStatusError BadCRC } ide: failed opcode was: unknown hda: dma_intr: status=0x51 { DriveReady SeekComplete Error } hda: dma_intr: error=0x84 { DriveStatusError BadCRC } ide: failed opcode was: unknown hda: dma_intr: status=0x51 { DriveReady SeekComplete Error } hda: dma_intr: error=0x84 { DriveStatusError BadCRC } ide: failed opcode was: unknown ide0: reset: success hda: dma_intr: status=0x51 { DriveReady SeekComplete Error } hda: dma_intr: error=0x84 { DriveStatusError BadCRC } ide: failed opcode was: unknown hda: dma_intr: status=0x51 { DriveReady SeekComplete Error } hda: dma_intr: error=0x84 { DriveStatusError BadCRC } ide: failed opcode was: unknown hda: dma_intr: status=0x51 { DriveReady SeekComplete Error } hda: dma_intr: error=0x84 { DriveStatusError BadCRC } ide: failed opcode was: unknown hda: dma_intr: status=0x51 { DriveReady SeekComplete Error } hda: dma_intr: error=0x84 { DriveStatusError BadCRC } ide: failed opcode was: unknown ide0: reset: success hda1 hda2 hda3 ide-floppy driver 0.99.newide usbcore: registered new driver hiddev usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.0:USB HID core driver mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard on isa0060/serio0 input: ImPS/2 Logitech Wheel Mouse on isa0060/serio1 md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27 NET: Registered protocol family 2 IP: routing cache hash table of 1024 buckets, 32Kbytes TCP: Hash tables configured (established 131072 bind 37449) Initializing IPsec netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 Freeing unused kernel memory: 144k freed Red Hat nash version 4.1.18 starting Mounted /proc filesystem Mounting sysfs Creating /dev Starting udev Loading jbd.ko module Loading ext3.ko module Creating root device Mounting root filesystem kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. Switching to new root SELinux: Disabled at runtime. SELinux: Unregistering netfilter hooks INIT: version 2.85 booting Welcome to Fedora Core Press 'I' to enter interactive startup. Starting udev: [ OK ] Initializing hardware... storage network audio done[ OK ] Configuring kernel parameters: [ OK ] Setting clock (utc): Tue Jan 1 11:50:35 CST 2002 [ OK ] Setting hostname linuxbios: [ OK ] Checking root filesystem [/sbin/fsck.ext3 (1) -- /] fsck.ext3 -a /dev/hda1 /1: clean, 333623/1026144 files, 1822094/2048279 blocks [ OK ] Remounting root filesystem in read-write mode: [ OK ] Setting up Logical Volume Management: [ OK ] Checking filesystems Checking all file systems. [/sbin/fsck.ext3 (1) -- /home] fsck.ext3 -a /dev/hda3 /home1: clean, 32800/8863744 files, 531251/17697605 blocks [ OK ] Mounting local filesystems: [ OK ] Enabling local filesystem quotas: [ OK ] Enabling swap space: [ OK ] INIT: Entering runlevel: 3 Entering non-interactive startup Starting sysstat: [ OK ] Checking for new hardware [ OK ] Applying iptables firewall rules: [ OK ] Starting pcmcia: [ OK ] Setting network parameters: [ OK ] Bringing up loopback interface: [ OK ] Starting system logger: [ OK ] Starting kernel logger: [ OK ] Starting irqbalance: [ OK ] Starting portmap: [ OK ] Starting NFS statd: [ OK ] Starting NFS4 idmapd: [ OK ] Mounting other filesystems: [ OK ] Starting lm_sensors: [ OK ] Starting automount:No Mountpoints Defined[ OK ] Starting nifd... Starting mDNSResponder... [ OK ] Starting smartd: [ OK ] Starting hpoj: [ OK ] Starting cups: [ OK ] Starting sshd:[ OK ] Starting xinetd: [ OK ] Starting sendmail: make: Warning: File `Makefile' has modification time 8.4e+07 s in the future make: warning: Clock skew detected. Your build may be incomplete. /usr/sbin/sendmail: /usr/sbin/sendmail: cannot execute binary file [FAILED] Starting sm-client: /usr/sbin/sendmail: /usr/sbin/sendmail: cannot execute binary file [FAILED] Starting console mouse services: [ OK ] Starting IIIMF input server: [ OK ] Starting Canna server: [ OK ] Starting crond: [ OK ] Starting xfs: [ OK ] Starting anacron: [ OK ] Starting atd: [ OK ] Starting system message bus: [ OK ] Starting cups-config-daemon: [ OK ] Starting HAL daemon: [ OK ] Fedora Core release 3 (Heidelberg) Kernel 2.6.9-1.667 on an i686 linuxbios login:
-- linuxbios mailing list [email protected] http://www.openbios.org/mailman/listinfo/linuxbios
