Hi I enabled IDE_DISK_POLL_DELAY = 1, AUTOBOOT_DELAY = 60 and still have IDE timeout... any suggestions? LinuxBIOS is detecting the IDE controller (it's shown in the boot log), so it seems like a problem with my FILO Config (listed below). Any suggestions?
Thanks, Chris -------------------------------------------------------------------------------------------------------------- # !!! NOTE !!! # Do NOT add spaces or comments at the end of option lines. # It confuses some versions of make. # Use grub instead of autoboot? #USE_GRUB = 1 # Grub menu.lst path MENULST_FILE = "hda3:/boot/filo/menu.lst" # Via Epia-MII CF boot: #MENULST_FILE = "hde1:/boot/filo/menu.lst" # time before default menu.lst is chosen. Set to 0 to ignore MENULST_TIMEOUT = 0 # Image filename for automatic boot and optional command line parameter AUTOBOOT_FILE = "hda2:/boot/vmlinuz root=/dev/hda2 initrd=/boot/initrd console=ttyS0,115200 console=tty0 video=atyfb:1024x768-16" #AUTOBOOT_FILE = "[EMAIL PROTECTED]" #AUTOBOOT_FILE = "[EMAIL PROTECTED]" #AUTOBOOT_FILE = "uda1:/vmlinuz.elf" # Time in second before booting AUTOBOOT_FILE AUTOBOOT_DELAY = 60 # Driver for hard disk, CompactFlash, and CD-ROM on IDE bus IDE_DISK = 1 # Add a short delay when polling status registers # (required on some broken SATA controllers) # NOTE: Slows down access significantly, so disable # whenever possible. IDE_DISK_POLL_DELAY = 1 # Use PCMCIA compact flash on Via Epia MII10000 and MII6000E # This device is referred to as hde. #PCMCIA_CF = 1 # Driver for USB Storage USB_DISK = 1 # VGA text console VGA_CONSOLE = 1 PC_KEYBOARD = 1 # Serial console SERIAL_CONSOLE = 1 SERIAL_IOBASE = 0x3f8 # if SERIAL_SPEED is commented out, the speed will not be changed. SERIAL_SPEED = 115200 # Filesystems FSYS_EXT2FS = 1 FSYS_FAT = 1 FSYS_JFS = 1 FSYS_MINIX = 1 FSYS_REISERFS = 1 FSYS_XFS = 1 FSYS_ISO9660 = 1 # Support for boot disk image in bootable CD-ROM (El Torito) ELTORITO = 1 # PCI support SUPPORT_PCI = 1 # Enable this to scan PCI busses above bus 0 # AMD64 based boards do need this. PCI_BRUTE_SCAN = 1 PCI_CONFIG_1 = 1 # Sound support (needs SUPPORT_PCI) #SUPPORT_SOUND = 1 # Sound drivers #VIA_SOUND = 1 # Debugging #DEBUG_ALL = 1 #DEBUG_ELFBOOT = 1 #DEBUG_ELFNOTE = 1 #DEBUG_LINUXBIOS = 1 #DEBUG_MALLOC = 1 #DEBUG_MULTIBOOT = 1 #DEBUG_SEGMENT = 1 #DEBUG_SYS_INFO = 1 #DEBUG_TIMER = 1 #DEBUG_BLOCKDEV = 1 #DEBUG_PCI = 1 #DEBUG_VIA_SOUND = 1 #DEBUG_LINUXLOAD = 1 #DEBUG_IDE = 1 #DEBUG_USB = 1 #DEBUG_ELTORITO = 1 # i386 options # Loader for standard Linux kernel image, a.k.a. /vmlinuz LINUX_LOADER = 1 # Boot FILO from Multiboot loader (eg. GRUB) #MULTIBOOT_IMAGE = 1 > * Lu, Yinghai <[EMAIL PROTECTED]> [061012 19:59]: > >> It turns out >> FILO need 45s to find the WD 40G HD, and Kernel need 15s. >> For the 200G WD HD, FILO and Kernel need less 1 second to find it. >> >> Looks like CK804 SATA is picky for SATA disk too. It can not find some >> sata disk. >> > > You need to enable the delay in FILO config > > -- linuxbios mailing list [email protected] http://www.openbios.org/mailman/listinfo/linuxbios
