I'm using Etherboot version 5.4.2 from etherboot.org.
I'm using LinuxBIOS version2-2394 and a i386 board.
The error is when I want to boot linux which is on device USB (so I use FILO
in Etherboot). I use LinuxBIOS and Etherboot. LinuxBIOS works properly, and
when I want to load linux, I have this error:
HCI at 000030c0
failed_transaction: TD(0002e5a0):
failed_transaction: type: SETUP
failed_transaction: retries: 00000003
failed_transaction: IOC
failed_transaction: active: 00000001
failed_transaction: device_addr: 00000000
failed_transaction: endpoint: 00000000
failed_transaction: data_toggle: 00000000
failed_transaction: max_transfer: 00000007
failed_transaction: actual: 00000000
failed_transaction: link:
failed_transaction: addr: 0002e5c0
failed_transaction: raw addr: 0003e770
failed_transaction: terminate: 00000000
failed_transaction: queue: 00000000
failed_transaction: depth: 00000000
failed_transaction: TD(0002e5c0):
failed_transaction: type: IN
failed_transaction: retries: 00000000
failed_transaction: active: 00000001
failed_transaction: device_addr: 00000000
failed_transaction: endpoint: 00000000
failed_transaction: data_toggle: 00000001
failed_transaction: max_transfer: 000007ff
failed_transaction: actual: 00000000
failed_transaction: link:
failed_transaction: addr: fffefe50
failed_transaction: raw addr: 00000000
failed_transaction: terminate: 00000001
failed_transaction: queue: 00000000
failed_transaction: depth: 00000000
configure_device: set_address failed!
and it repeats it.
I suppose I have a bad config. So can you give me a config an example of
config in order to boot on USB.
Thanks for your help!
From: Stefan Reinauer <[EMAIL PROTECTED]>
To: jean raymond <[EMAIL PROTECTED]>
CC: [email protected]
Subject: Re: [LinuxBIOS] USB Bootloader
Date: Thu, 2 Nov 2006 11:32:44 +0100
* jean raymond <[EMAIL PROTECTED]> [061102 07:53]:
> Hello,
>
> I tried filo 0.4 from openbios.org, which was able to ide boot but hangs
> on usb boot with this:
Interesting... There is no filo 0.4 on openbios.org ;-) Only 0.5...
> n_type: 00000001 n_name(8): ELFBoot n_desc(10): Etherboot
> n_type: 00000002 n_name(8): ELFBoot n_desc(6): 5.4.2
> Loading Etherboot version: 5.4.2
So you are using etherboot from etherboot.org?
Yinghai, can you help?
> Boot from (N)etwork (D)isk or (Q)uit? D
> FILO version 0.4.1 ([EMAIL PROTECTED]) Tue Oct 31 17:00:24 CET 2006
> Press <Enter> for default boot, or <Esc> for boot prompt...
> boot: uda1:/bzImage root=/dev/sda2 console=tty0 console=ttyS0,115200
> dev=uda1, path=/bzImage
> name = uda1, type = 3, drive = 0, part = 1, offset = 0x00000000, length
=
> 0x00000000
> LinuxLabs USB bootloader
> Resetting UHCI
> uhc_init setting framelist to: 000101b0
> Starting UHCI
> HCI at 000030c0
> Resetting UHCI
> uhc_init setting framelist to: 000101b0
> Starting UHCI
> HCI at 000030e0
> frame_list is at bffede50
> frame_list_link: addr: fffefe50
> frame_list_link: raw addr: 00000800
> frame_list_link: terminate: 00000000
> frame_list_link: queue: 00000000
> frame_list_link: depth: 00000000
> frame_list is at bffebe50
> frame_list_link: addr: ffff0650
> frame_list_link: raw addr: 00000040
> frame_list_link: terminate: 00000000
> frame_list_link: queue: 00000000
> frame_list_link: depth: 00000000
> New USB device, setting address 2
> port = 0x000030d0 controller =0x00000000 lowspeed = 0
next_usb_dev
> = 0x00000003 addr = 0x00000002
> uhci_control_msg: request_type = 00000000 request = 00000005 wLength=0
> ctrl_msg( 00000000, 00000000, 00000005, 00000002, 00000000, 00000000, p)
> 0 bytes in payload
> lowspeed = u
> HCI at 000030c0
> failed_transaction: TD(0002e5a0):
> failed_transaction: type: SETUP
> failed_transaction: retries: 00000003
> failed_transaction: IOC
> failed_transaction: active: 00000001
> failed_transaction: device_addr: 00000000
> failed_transaction: endpoint: 00000000
> failed_transaction: data_toggle: 00000000
> failed_transaction: max_transfer: 00000007
> failed_transaction: actual: 00000000
> failed_transaction: link:
> failed_transaction: addr: 0002e5c0
> failed_transaction: raw addr: 0003e770
> failed_transaction: terminate: 00000000
> failed_transaction: queue: 00000000
> failed_transaction: depth: 00000000
> failed_transaction: TD(0002e5c0):
> failed_transaction: type: IN
> failed_transaction: retries: 00000000
> failed_transaction: active: 00000001
> failed_transaction: device_addr: 00000000
> failed_transaction: endpoint: 00000000
> failed_transaction: data_toggle: 00000001
> failed_transaction: max_transfer: 000007ff
> failed_transaction: actual: 00000000
> failed_transaction: link:
> failed_transaction: addr: fffefe50
> failed_transaction: raw addr: 00000000
> failed_transaction: terminate: 00000001
> failed_transaction: queue: 00000000
> failed_transaction: depth: 00000000
> configure_device: set_address failed!
> value = 0x00001080
> poll_usb 1 hc_type[1] = 00000000
>
> ...
> There is a USB device, but it won't init! This is a bad thing.
> failed to open usb
> boot: uda1:/bzImage root=/dev/sda2 console=tty0 console=ttyS0,115200
What board are you using, what LinuxBIOS revision,...?
> Now, how can etherboot-filo be fixed to boot at all?
> And, how can filo 0.5 be fixed to boot USB?
What's the error you are seeing with filo 0.5?
Stefan
--
coresystems GmbH ⢠Brahmsstr. 16 ⢠D-79104 Freiburg i. Br.
Tel.: +49 761 7668825 ⢠Fax: +49 761 7664613
Email: [EMAIL PROTECTED] ⢠http://www.coresystems.de/
--
linuxbios mailing list
[email protected]
http://www.openbios.org/mailman/listinfo/linuxbios
_________________________________________________________________
Add a Yahoo! contact to Windows Live Messenger for a chance to win a free
trip!
http://www.imagine-windowslive.com/minisites/yahoo/default.aspx?locale=en-us&hmtagline
--
linuxbios mailing list
[email protected]
http://www.openbios.org/mailman/listinfo/linuxbios
