Just got my bios savior, so now I'm ready to try to make linuxbios work
on my abit kn9 ultra.
Attached the lspci -vv and dmidecode.
First things first: After more PCI-IDs was added to flash_enable.c
flashrom was able to find my bios chip:
Calibrating delay loop... Setting up microsecond timing loop
730M loops per second
ok
No LinuxBIOS table found.
Enabling flash write on NVIDIA MCP55...OK
Trying SST49LF040, 512 KB
probe_jedec: id1 0xbf, id2 0x51
SST49LF040 found at physical address: 0xfff80000
Flash part is SST49LF040 (512 KB)
OK, only ENABLING flash write, but NOT FLASHING.
Reading with -r does not look like the original bios, as there is
readable text in the read image, like "Phoenix Technologies, LTD", this
is not visible in the original bios image. Is this correct? This was
discussed in a previous thread called "
mcp55 flashrom problem".
Trying to write a linuxbios image I built (which does probably not work
yet anyway):
[EMAIL PROTECTED] flashrom]# ./flashrom -vV -c SST49LF040 -w linuxbios.rom
Calibrating delay loop... Setting up microsecond timing loop
727M loops per second
ok
No LinuxBIOS table found.
Enabling flash write on NVIDIA MCP55...OK
Trying SST49LF040, 512 KB
probe_jedec: id1 0xbf, id2 0x51
SST49LF040 found at physical address: 0xfff80000
Flash part is SST49LF040 (512 KB)
LinuxBIOS last image size (not rom size) is 4096 bytes.
MANUFACTURER: ABIT
MAINBOARD ID: kn9_ultra
Note: If the following flash access fails, you might need to specify -m
<vendor>:<mainboard>
Programming Page: 0127 at address: 0x0007f000
Verifying flash address: 0x00000000 - FAILED
Flashing the original bios to the bios savior did not work, so I used
awdflash instead. That worked fine.
Any help appreciated, both for making flashrom work, and also how to
make linuxbios work. I started by copying nvidia/l1_2pvv in target and
mainboard. Can someone look at the attached files and give me a step by
step guide on how to try to make things work?
Karl Erik
00:00.0 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a1)
Subsystem: ABIT Computer Corp. Unknown device 1c24
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [44] HyperTransport: Slave or Primary Interface
Command: BaseUnitID=0 UnitCnt=15 MastHost- DefDir- DUL-
Link Control 0: CFlE+ CST- CFE- <LkFail- Init+ EOC- TXO-
<CRCErr=0 IsocEn- LSEn+ ExtCTL- 64b-
Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit
DwFcInEn- LWO=16bit DwFcOutEn-
Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+
<CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit
DwFcInEn- LWO=8bit DwFcOutEn-
Revision ID: 1.03
Link Frequency 0: 1.0GHz
Link Error 0: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 0: 200MHz+ 300MHz+ 400MHz+ 500MHz+
600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD-
Link Frequency 1: 200MHz
Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz-
600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Error Handling: PFlE+ OFlE+ PFE- OFE- EOCFE- RFE- CRCFE-
SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE-
Prefetchable memory behind bridge Upper: 00-00
Bus Number: 00
Capabilities: [e0] #00 [fee0]
00:01.0 ISA bridge: nVidia Corporation MCP55 LPC Bridge (rev a2)
Subsystem: ABIT Computer Corp. Unknown device 1c24
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
00:01.1 SMBus: nVidia Corporation MCP55 SMBus (rev a2)
Subsystem: ABIT Computer Corp. Unknown device 1c24
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at fc00 [size=64]
Region 4: I/O ports at 1c00 [size=64]
Region 5: I/O ports at 1c40 [size=64]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.2 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a2)
Subsystem: ABIT Computer Corp. Unknown device 1c24
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
00:02.0 USB Controller: nVidia Corporation MCP55 USB Controller (rev a1)
(prog-if 10 [OHCI])
Subsystem: ABIT Computer Corp. Unknown device 1c24
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 23
Region 0: Memory at fe02f000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:02.1 USB Controller: nVidia Corporation MCP55 USB Controller (rev a2)
(prog-if 20 [EHCI])
Subsystem: ABIT Computer Corp. Unknown device 1c24
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 22
Region 0: Memory at fe02e000 (32-bit, non-prefetchable) [size=256]
Capabilities: [44] Debug port
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:04.0 IDE interface: nVidia Corporation MCP55 IDE (rev a1) (prog-if 8a
[Master SecP PriP])
Subsystem: ABIT Computer Corp. Unknown device 1c24
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Region 4: I/O ports at f000 [size=16]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:05.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a2)
(prog-if 85 [Master SecO PriO])
Subsystem: ABIT Computer Corp. Unknown device 1c24
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at 09f0 [size=8]
Region 1: I/O ports at 0bf0 [size=4]
Region 2: I/O ports at 0970 [size=8]
Region 3: I/O ports at 0b70 [size=4]
Region 4: I/O ports at dc00 [size=16]
Region 5: Memory at fe02d000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [b0] Message Signalled Interrupts: 64bit+ Queue=0/2
Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [cc] HyperTransport: MSI Mapping
00:05.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a2)
(prog-if 85 [Master SecO PriO])
Subsystem: ABIT Computer Corp. Unknown device 1c24
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 20
Region 0: I/O ports at 09e0 [size=8]
Region 1: I/O ports at 0be0 [size=4]
Region 2: I/O ports at 0960 [size=8]
Region 3: I/O ports at 0b60 [size=4]
Region 4: I/O ports at c800 [size=16]
Region 5: Memory at fe02c000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [b0] Message Signalled Interrupts: 64bit+ Queue=0/2
Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [cc] HyperTransport: MSI Mapping
00:05.2 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a2)
(prog-if 85 [Master SecO PriO])
Subsystem: ABIT Computer Corp. Unknown device 1c24
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin C routed to IRQ 23
Region 0: I/O ports at c400 [size=8]
Region 1: I/O ports at c000 [size=4]
Region 2: I/O ports at bc00 [size=8]
Region 3: I/O ports at b800 [size=4]
Region 4: I/O ports at b400 [size=16]
Region 5: Memory at fe02b000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [b0] Message Signalled Interrupts: 64bit+ Queue=0/2
Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [cc] HyperTransport: MSI Mapping
00:06.0 PCI bridge: nVidia Corporation MCP55 PCI bridge (rev a2) (prog-if 01
[Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 00009000-00009fff
Memory behind bridge: fde00000-fdefffff
Prefetchable memory behind bridge: ec000000-efffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [b8] #0d [0000]
Capabilities: [8c] HyperTransport: MSI Mapping
00:08.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a2)
Subsystem: ABIT Computer Corp. Unknown device 1c24
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 22
Region 0: Memory at fe02a000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at b000 [size=8]
Region 2: Memory at fe029000 (32-bit, non-prefetchable) [size=256]
Region 3: Memory at fe028000 (32-bit, non-prefetchable) [size=16]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable+ DSel=0 DScale=0 PME-
Capabilities: [70] MSI-X: Enable- Mask- TabSize=8
Vector table: BAR=2 offset=00000000
PBA: BAR=3 offset=00000000
Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/3
Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [6c] HyperTransport: MSI Mapping
00:09.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a2)
Subsystem: ABIT Computer Corp. Unknown device 1c24
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 21
Region 0: Memory at fe027000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at ac00 [size=8]
Region 2: Memory at fe026000 (32-bit, non-prefetchable) [size=256]
Region 3: Memory at fe025000 (32-bit, non-prefetchable) [size=16]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable+ DSel=0 DScale=0 PME-
Capabilities: [70] MSI-X: Enable- Mask- TabSize=8
Vector table: BAR=2 offset=00000000
PBA: BAR=3 offset=00000000
Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/3
Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [6c] HyperTransport: MSI Mapping
00:0c.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a2)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 00008000-00008fff
Memory behind bridge: fdd00000-fddfffff
Prefetchable memory behind bridge: 00000000fdc00000-00000000fdc00000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] #0d [0000]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/1
Enable+
Address: 00000000fee00000 Data: 4039
Capabilities: [60] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <512ns, L1 <4us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 256 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 3
Link: Latency L0s <512ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x4
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [100] Virtual Channel
00:0d.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a2)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 00007000-00007fff
Memory behind bridge: fdb00000-fdbfffff
Prefetchable memory behind bridge: 00000000fda00000-00000000fda00000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] #0d [0000]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/1
Enable+
Address: 00000000fee00000 Data: 4041
Capabilities: [60] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <512ns, L1 <4us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 256 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 2
Link: Latency L0s <512ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x4
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [100] Virtual Channel
00:0e.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a2)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 00006000-00006fff
Memory behind bridge: fd900000-fd9fffff
Prefetchable memory behind bridge: 00000000fd800000-00000000fd800000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] #0d [0000]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/1
Enable+
Address: 00000000fee00000 Data: 4049
Capabilities: [60] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <512ns, L1 <4us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 256 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 1
Link: Latency L0s <512ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x8
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [100] Virtual Channel
00:0f.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a2)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
I/O behind bridge: 00005000-00005fff
Memory behind bridge: fa000000-fcffffff
Prefetchable memory behind bridge: 00000000d0000000-00000000dff00000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [40] #0d [0000]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/1
Enable+
Address: 00000000fee00000 Data: 4051
Capabilities: [60] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <512ns, L1 <4us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s L1, Port 0
Link: Latency L0s <512ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x16
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [100] Virtual Channel
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
HyperTransport Technology Configuration
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Capabilities: [80] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Revision ID: 1.02
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address
Map
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM
Controller
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Miscellaneous Control
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Capabilities: [f0] #0f [0010]
01:08.0 FireWire (IEEE 1394): Texas Instruments TSB43AB22/A IEEE-1394a-2000
Controller (PHY/Link) (prog-if 10 [OHCI])
Subsystem: ABIT Computer Corp. Unknown device 1c20
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 1000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fdeff000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at fdef8000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
01:09.0 Multimedia video controller: Internext Compression Inc iTVC15 MPEG-2
Encoder (rev 01)
Subsystem: Hauppauge computer works Inc. WinTV PVR-350
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (32000ns min, 2000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at ec000000 (32-bit, prefetchable) [size=64M]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
05:00.0 VGA compatible controller: nVidia Corporation G70 [GeForce 7600 GS]
(rev a1) (prog-if 00 [VGA])
Subsystem: Micro-Star International Co., Ltd. NX7600GS-T2D256EH
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fa000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at fb000000 (64-bit, non-prefetchable) [size=16M]
Region 5: I/O ports at 5c00 [size=128]
[virtual] Expansion ROM at fc000000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [68] Message Signalled Interrupts: 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [78] Express Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <256ns, L1 <4us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s L1, Port 0
Link: Latency L0s <256ns, L1 <4us
Link: ASPM Disabled RCB 128 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x16
Capabilities: [100] Virtual Channel
Capabilities: [128] Power Budgeting
# dmidecode 2.7
SMBIOS 2.5 present.
43 structures occupying 1771 bytes.
Table at 0x000F0000.
Handle 0x0000, DMI type 0, 24 bytes.
BIOS Information
Vendor: Phoenix Technologies, LTD
Version: 6.00 PG
Release Date: 01/16/2007
Address: 0xE0000
Runtime Size: 128 kB
ROM Size: 512 kB
Characteristics:
ISA is supported
PCI is supported
PNP is supported
APM is supported
BIOS is upgradeable
BIOS shadowing is allowed
Boot from CD is supported
Selectable boot is supported
BIOS ROM is socketed
EDD is supported
5.25"/360 KB floppy services are supported (int 13h)
5.25"/1.2 MB floppy services are supported (int 13h)
3.5"/720 KB floppy services are supported (int 13h)
3.5"/2.88 MB floppy services are supported (int 13h)
Print screen service is supported (int 5h)
8042 keyboard services are supported (int 9h)
Serial services are supported (int 14h)
Printer services are supported (int 17h)
CGA/mono video services are supported (int 10h)
ACPI is supported
USB legacy is supported
LS-120 boot is supported
ATAPI Zip drive boot is supported
BIOS boot specification is supported
Handle 0x0001, DMI type 1, 27 bytes.
System Information
Manufacturer: Unknow
Product Name: Unknow
Version: Unknow
Serial Number: Unknow
UUID: 00000000-0000-0000-0000-044B80808003
Wake-up Type: Power Switch
SKU Number:
Family:
Handle 0x0002, DMI type 2, 8 bytes.
Base Board Information
Manufacturer: http://www.abit.com.tw/
Product Name: KN9(NF-MCP55 series)
Version: 1.x
Serial Number:
Handle 0x0003, DMI type 3, 17 bytes.
Chassis Information
Manufacturer: Unknow
Type: Desktop
Lock: Not Present
Version: Unknow
Serial Number:
Asset Tag:
Boot-up State: Unknown
Power Supply State: Unknown
Thermal State: Unknown
Security Status: Unknown
OEM Information: 0x00000000
Handle 0x0004, DMI type 4, 40 bytes.
Processor Information
Socket Designation: Socket AM2
Type: Central Processor
Family: <OUT OF SPEC>
Manufacturer: AMD
ID: B2 0F 04 00 FF FB 8B 17
Version: AMD Athlon(tm) 64 X2 Dual Core Processor 4600+
Voltage: 1.3 V
External Clock: 200 MHz
Max Speed: 3000 MHz
Current Speed: 2400 MHz
Status: Populated, Enabled
Upgrade: Socket 940
L1 Cache Handle: 0x000A
L2 Cache Handle: 0x000B
L3 Cache Handle: Not Provided
Serial Number:
Asset Tag:
Part Number:
Handle 0x0005, DMI type 5, 24 bytes.
Memory Controller Information
Error Detecting Method: 64-bit ECC
Error Correcting Capabilities:
None
Supported Interleave: One-way Interleave
Current Interleave: One-way Interleave
Maximum Memory Module Size: 4096 MB
Maximum Total Memory Size: 16384 MB
Supported Speeds:
70 ns
60 ns
50 ns
Supported Memory Types:
Standard
DIMM
Memory Module Voltage: 2.9 V
Associated Memory Slots: 4
0x0006
0x0007
0x0008
0x0009
Enabled Error Correcting Capabilities: None
Handle 0x0006, DMI type 6, 12 bytes.
Memory Module Information
Socket Designation: A0
Bank Connections: None
Current Speed: 6 ns
Type: Other Unknown EDO
Installed Size: Not Installed
Enabled Size: Not Installed
Error Status: OK
Handle 0x0007, DMI type 6, 12 bytes.
Memory Module Information
Socket Designation: A1
Bank Connections: None
Current Speed: 6 ns
Type: Other Unknown EDO
Installed Size: Not Installed
Enabled Size: Not Installed
Error Status: OK
Handle 0x0008, DMI type 6, 12 bytes.
Memory Module Information
Socket Designation: A2
Bank Connections: 4
Current Speed: 6 ns
Type: Other Unknown EDO
Installed Size: 512 MB (Single-bank Connection)
Enabled Size: 512 MB (Single-bank Connection)
Error Status: OK
Handle 0x0009, DMI type 6, 12 bytes.
Memory Module Information
Socket Designation: A3
Bank Connections: 6
Current Speed: 6 ns
Type: Other Unknown EDO
Installed Size: 512 MB (Single-bank Connection)
Enabled Size: 512 MB (Single-bank Connection)
Error Status: OK
Handle 0x000A, DMI type 7, 19 bytes.
Cache Information
Socket Designation: Internal Cache
Configuration: Enabled, Not Socketed, Level 1
Operational Mode: Write Back
Location: Internal
Installed Size: 128 KB
Maximum Size: 128 KB
Supported SRAM Types:
Synchronous
Installed SRAM Type: Synchronous
Speed: Unknown
Error Correction Type: Unknown
System Type: Unknown
Associativity: Unknown
Handle 0x000B, DMI type 7, 19 bytes.
Cache Information
Socket Designation: External Cache
Configuration: Enabled, Not Socketed, Level 2
Operational Mode: Write Back
Location: Internal
Installed Size: 512 KB
Maximum Size: 512 KB
Supported SRAM Types:
Synchronous
Installed SRAM Type: Synchronous
Speed: Unknown
Error Correction Type: Unknown
System Type: Unknown
Associativity: Unknown
Handle 0x000C, DMI type 8, 9 bytes.
Port Connector Information
Internal Reference Designator: PRIMARY IDE
Internal Connector Type: On Board IDE
External Reference Designator: Not Specified
External Connector Type: None
Port Type: Other
Handle 0x000D, DMI type 8, 9 bytes.
Port Connector Information
Internal Reference Designator: SECONDARY IDE
Internal Connector Type: On Board IDE
External Reference Designator: Not Specified
External Connector Type: None
Port Type: Other
Handle 0x000E, DMI type 8, 9 bytes.
Port Connector Information
Internal Reference Designator: FDD
Internal Connector Type: On Board Floppy
External Reference Designator: Not Specified
External Connector Type: None
Port Type: 8251 FIFO Compatible
Handle 0x000F, DMI type 8, 9 bytes.
Port Connector Information
Internal Reference Designator: COM1
Internal Connector Type: 9 Pin Dual Inline (pin 10 cut)
External Reference Designator:
External Connector Type: DB-9 male
Port Type: Serial Port 16450 Compatible
Handle 0x0010, DMI type 8, 9 bytes.
Port Connector Information
Internal Reference Designator: COM2
Internal Connector Type: 9 Pin Dual Inline (pin 10 cut)
External Reference Designator:
External Connector Type: DB-9 male
Port Type: Serial Port 16450 Compatible
Handle 0x0011, DMI type 8, 9 bytes.
Port Connector Information
Internal Reference Designator: LPT1
Internal Connector Type: DB-25 female
External Reference Designator:
External Connector Type: DB-25 female
Port Type: Parallel Port ECP/EPP
Handle 0x0012, DMI type 8, 9 bytes.
Port Connector Information
Internal Reference Designator: Keyboard
Internal Connector Type: PS/2
External Reference Designator:
External Connector Type: PS/2
Port Type: Keyboard Port
Handle 0x0013, DMI type 8, 9 bytes.
Port Connector Information
Internal Reference Designator: PS/2 Mouse
Internal Connector Type: PS/2
External Reference Designator:
External Connector Type: PS/2
Port Type: Mouse Port
Handle 0x0014, DMI type 8, 9 bytes.
Port Connector Information
Internal Reference Designator: Not Specified
Internal Connector Type: None
External Reference Designator: USB0
External Connector Type: Other
Port Type: USB
Handle 0x0015, DMI type 9, 13 bytes.
System Slot Information
Designation: PCI0
Type: 32-bit PCI
Current Usage: In Use
Length: Long
ID: 1
Characteristics:
5.0 V is provided
PME signal is supported
Handle 0x0016, DMI type 9, 13 bytes.
System Slot Information
Designation: PCI1
Type: 32-bit PCI
Current Usage: Available
Length: Long
ID: 2
Characteristics:
5.0 V is provided
PME signal is supported
Handle 0x0017, DMI type 9, 13 bytes.
System Slot Information
Designation: PCI2
Type: 32-bit PCI
Current Usage: In Use
Length: Long
ID: 3
Characteristics:
5.0 V is provided
PME signal is supported
Handle 0x0018, DMI type 9, 13 bytes.
System Slot Information
Designation: PCI3
Type: 32-bit PCI Express
Current Usage: In Use
Length: Long
Characteristics:
5.0 V is provided
PME signal is supported
Handle 0x0019, DMI type 9, 13 bytes.
System Slot Information
Designation: PCI4
Type: 32-bit PCI Express
Current Usage: In Use
Length: Long
Characteristics:
5.0 V is provided
PME signal is supported
Handle 0x001A, DMI type 9, 13 bytes.
System Slot Information
Designation: PCI5
Type: 32-bit PCI Express
Current Usage: In Use
Length: Long
Characteristics:
5.0 V is provided
PME signal is supported
Handle 0x001B, DMI type 9, 13 bytes.
System Slot Information
Designation: PCI6
Type: 32-bit PCI Express
Current Usage: In Use
Length: Long
Characteristics:
5.0 V is provided
PME signal is supported
Handle 0x001C, DMI type 13, 22 bytes.
BIOS Language Information
Installable Languages: 3
n|US|iso8859-1
n|US|iso8859-1
r|CA|iso8859-1
Currently Installed Language: n|US|iso8859-1
Handle 0x001D, DMI type 16, 15 bytes.
Physical Memory Array
Location: System Board Or Motherboard
Use: System Memory
Error Correction Type: None
Maximum Capacity: 16 GB
Error Information Handle: Not Provided
Number Of Devices: 4
Handle 0x001E, DMI type 17, 27 bytes.
Memory Device
Array Handle: 0x001D
Error Information Handle: Not Provided
Total Width: 64 bits
Data Width: 64 bits
Size: No Module Installed
Form Factor: DIMM
Set: None
Locator: A0
Bank Locator: Bank0/1
Type: Unknown
Type Detail: None
Speed: Unknown
Manufacturer: None
Serial Number: None
Asset Tag: None
Part Number: None
Handle 0x001F, DMI type 17, 27 bytes.
Memory Device
Array Handle: 0x001D
Error Information Handle: Not Provided
Total Width: 64 bits
Data Width: 64 bits
Size: No Module Installed
Form Factor: DIMM
Set: None
Locator: A1
Bank Locator: Bank2/3
Type: Unknown
Type Detail: None
Speed: Unknown
Manufacturer: None
Serial Number: None
Asset Tag: None
Part Number: None
Handle 0x0020, DMI type 17, 27 bytes.
Memory Device
Array Handle: 0x001D
Error Information Handle: Not Provided
Total Width: 64 bits
Data Width: 64 bits
Size: 512 MB
Form Factor: DIMM
Set: None
Locator: A2
Bank Locator: Bank4/5
Type: Unknown
Type Detail: None
Speed: Unknown
Manufacturer: None
Serial Number: None
Asset Tag: None
Part Number: None
Handle 0x0021, DMI type 17, 27 bytes.
Memory Device
Array Handle: 0x001D
Error Information Handle: Not Provided
Total Width: 64 bits
Data Width: 64 bits
Size: 512 MB
Form Factor: DIMM
Set: None
Locator: A3
Bank Locator: Bank6/7
Type: Unknown
Type Detail: None
Speed: Unknown
Manufacturer: None
Serial Number: None
Asset Tag: None
Part Number: None
Handle 0x0022, DMI type 19, 15 bytes.
Memory Array Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x0003FFFFFFF
Range Size: 1 GB
Physical Array Handle: 0x001D
Partition Width: 0
Handle 0x0023, DMI type 20, 19 bytes.
Memory Device Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x000000003FF
Range Size: 1 kB
Physical Device Handle: 0x001E
Memory Array Mapped Address Handle: 0x0022
Partition Row Position: 1
Handle 0x0024, DMI type 20, 19 bytes.
Memory Device Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x000000003FF
Range Size: 1 kB
Physical Device Handle: 0x001F
Memory Array Mapped Address Handle: 0x0022
Partition Row Position: 1
Handle 0x0025, DMI type 20, 19 bytes.
Memory Device Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x0001FFFFFFF
Range Size: 512 MB
Physical Device Handle: 0x0020
Memory Array Mapped Address Handle: 0x0022
Partition Row Position: 1
Handle 0x0026, DMI type 20, 19 bytes.
Memory Device Mapped Address
Starting Address: 0x00020000000
Ending Address: 0x0003FFFFFFF
Range Size: 512 MB
Physical Device Handle: 0x0021
Memory Array Mapped Address Handle: 0x0022
Partition Row Position: 1
Handle 0x0027, DMI type 32, 11 bytes.
System Boot Information
Status: No errors detected
Handle 0x0028, DMI type 188, 255 bytes.
OEM-specific Type
Header and Data:
BC FF 28 00 4B 38 4E 50 54 44 52 41 4D 30 03 00
00 00 00 00 3F 00 00 00 00 00 01 00 00 00 00 00
00 00 02 00 00 00 00 00 00 00 03 00 00 00 00 00
00 00 04 00 00 00 00 00 00 00 05 00 00 00 00 00
00 00 06 00 00 00 00 00 00 00 07 00 00 00 00 00
00 00 40 00 10 0A 00 00 00 00 00 00 05 00 EB 02
00 AE 00 00 00 00 00 00 00 00 01 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 E0 3F 38 00 00 00 00 00 00 00
00 00 46 00 00 00 00 00 00 00 20 00 00 00 00 00
00 00 24 C2 6A AE 20 13 82 00 10 08 01 00 5A 80
00 64 88 88 FF FE 16 15 17 17 16 15 15 16 16 00
00 00 17 17 16 17 17 17 17 16 17 00 00 00 00 35
00 00 16 15 15 16 16 15 15 15 16 18 17 17 16 16
18 18 19 18 00 36 00 00 22 12 11 20 20 22 20 00
22 12 11 20 20 22 20 00 00 00 00 00 00 00 00
Strings:
Handle 0x0029, DMI type 190, 255 bytes.
OEM-specific Type
Header and Data:
BE FF 29 00 00 00 00 40 00 00 00 00 00 00 00 00
00 00 00 00 01 06 16 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Strings:
Handle 0x002A, DMI type 127, 4 bytes.
End Of Table
--
linuxbios mailing list
[email protected]
http://www.linuxbios.org/mailman/listinfo/linuxbios
