Hi,
2007/6/3, Stefan Reinauer <[EMAIL PROTECTED]>:
Please sign off the patch according to
http://www.linuxbios.org/Development_Guidelines#Sign-off_Procedure
so we can check this patch in!
Add sign-off.
2007/6/3, Juergen Beisert <[EMAIL PROTECTED]>:
As your dmesg output shows, the graphical console is active. I missed
something to setup correctly. When my LinuxBIOS activates the VGA the linux
console runs as expected. Without it, everything seems ok, but no output
occures. I don't know why, yet.
How You activates VGA in LinuxBios?
2007/6/3, Uwe Hermann <[EMAIL PROTECTED]>:
On Sun, Jun 03, 2007 at 12:20:10AM +0600, Nikolay Petukhov wrote:
> Problems:
> Filo load bzImage only from ide0.
What does not work? ide1? AFAICS the boards only have one IDE port!?
The this boards has two IDE ports. IDE0 has 40-pin IDE connector. IDE1
has CF connector.
> diff -Nru LinuxBIOSv2-2700/src/mainboard/iei/juki511p/auto.c
LinuxBIOSv2-2700-juki/src/mainboard/iei/juki511p/auto.c
> --- LinuxBIOSv2-2700/src/mainboard/iei/juki511p/auto.c 1970-01-01
05:00:00.000000000 +0500
> +++ LinuxBIOSv2-2700-juki/src/mainboard/iei/juki511p/auto.c 2007-06-02
20:02:10.000000000 +0600
Please rename the directory to 'juki-511p' if possible, as that seems to be
the canonical (lowercase'd) name used by the vendor.
I had change directory name to 'juki_511p'.
> +#include "superio/winbond/w83977fa/w83977fa_early_serial.c"
Maybe this should be 'w83977f' (without the 'a')? IIRC, we omitted any
'-A' or '-AW' suffix from other Super I/Os, too. Comments anyone?
I agree. I did it.
> +void udelay(int usecs)
> +{
> + int i;
> + for(i = 0; i < usecs; i++)
> + outb(i&0xff, 0x80);
> +}
Is this needed? There's a global implementation in the repository
already.
I removed it.
> + device pnp 3f0.4 on # RTC
> + end
Is this ok if left empty?
My 'lspnp -v' (on another mainboard) says:
00:04 PNP0b00 AT real-time clock
state = active
io 0x70-0x71
irq 8
So maybe something like
device pnp 3f0.4 on # RTC
io 0x60 = 0x70
irq 0x70 = 8
end
is needed here? I'm just guessing, though, please correct me if I'm
wrong.
> + device pnp 3f0.5 on # Keyboard
> + io 0x60 = 0x60
> + io 0x62 = 0x64
> + irq 0x70 = 0x01 # int 1 for PS/2 keyboard
> + irq 0x72 = 0x0c # int 12 for PS/2 mouse
Why not like this? Easier to read, IMHO:
irq 0x70 = 1 # int 1 for PS/2 keyboard
irq 0x72 = 12 # int 12 for PS/2 mouse
> +const struct irq_routing_table intel_irq_routing_table = {
> + PIRQ_SIGNATURE, /* u32 signature */
> + PIRQ_VERSION, /* u16 version */
> + 32+16*2, /* There can be total 6 devices on the bus */
^
typo? ---> 2?
Maybe even
32+16*IRQ_SLOT_COUNT, /* There can be IRQ_SLOT_COUNT devices on the
bus */
I corrected it.
> diff -Nru LinuxBIOSv2-2700/src/northbridge/amd/gx1/raminit.c
LinuxBIOSv2-2700-juki/src/northbridge/amd/gx1/raminit.c
> --- LinuxBIOSv2-2700/src/northbridge/amd/gx1/raminit.c 2005-07-06
23:11:02.000000000 +0600
> +++ LinuxBIOSv2-2700-juki/src/northbridge/amd/gx1/raminit.c 2007-05-31
16:06:40.000000000 +0600
> @@ -324,6 +324,7 @@
> outb(0x70, 0x80);
>
> setGX1Mem(GX_BASE + MC_MEM_CNTRL2, 0x000007d8); /* Disable all CLKS,
Shift = 3 */
> +// setGX1Mem(GX_BASE + MC_MEM_CNTRL1, 0x92080000); /* MD_DS=2, MA_DS=2,
CNTL_DS=2 SDCLKRATE=2.5 */
> setGX1Mem(GX_BASE + MC_MEM_CNTRL1, 0x92140000); /* MD_DS=2, MA_DS=2,
CNTL_DS=2 SDCLKRATE=4 */
> setGX1Mem(GX_BASE + MC_BANK_CFG, 0x00700070); /* No DIMMS installed */
> setGX1Mem(GX_BASE + MC_SYNC_TIM1, 0x3a733225); /* LTMODE=3, RC=10,
RAS=7, RP=3, RCD=3, RRD=2, DPL=2 */
OK, not sure what we should do with this. Will it break other GX1-based
mainboards? Or is it generic for all GX1s?
I removed it.
> diff -Nru LinuxBIOSv2-2700/src/superio/winbond/w83977fa/chip.h
LinuxBIOSv2-2700-juki/src/superio/winbond/w83977fa/chip.h
> --- LinuxBIOSv2-2700/src/superio/winbond/w83977fa/chip.h 1970-01-01
05:00:00.000000000 +0500
> +++ LinuxBIOSv2-2700-juki/src/superio/winbond/w83977fa/chip.h 2007-06-02
18:52:57.000000000 +0600
Please provide an extra patch for the addition of the new Super I/O,
this is independant of the mainboards...
> diff -Nru LinuxBIOSv2-2700/targets/iei/juki511p/Config.lb
LinuxBIOSv2-2700-juki/targets/iei/juki511p/Config.lb
> --- LinuxBIOSv2-2700/targets/iei/juki511p/Config.lb 1970-01-01
05:00:00.000000000 +0500
> +++ LinuxBIOSv2-2700-juki/targets/iei/juki511p/Config.lb 2007-06-02
19:07:21.000000000 +0600
Please add a copyright header to this file, too.
Signed-off-by: Nikolay Petukhov <[EMAIL PROTECTED]>
--
Nikolay
-----------------------------------------------------------------
diff -Nru LinuxBIOSv2-2700/src/superio/winbond/w83977f/chip.h LinuxBIOSv2-2700-w83977f/src/superio/winbond/w83977f/chip.h
--- LinuxBIOSv2-2700/src/superio/winbond/w83977f/chip.h 1970-01-01 05:00:00.000000000 +0500
+++ LinuxBIOSv2-2700-w83977f/src/superio/winbond/w83977f/chip.h 2007-06-04 17:58:39.000000000 +0600
@@ -0,0 +1,30 @@
+/*
+ * This file is part of the LinuxBIOS project.
+ *
+ * Copyright (C) 2007 Nikolay Petukhov <[EMAIL PROTECTED]>
+ * Adapted from w83977tf
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <pc80/keyboard.h>
+#include <uart8250.h>
+
+extern struct chip_operations superio_winbond_w83977f_ops;
+
+struct superio_winbond_w83977f_config {
+ struct uart8250 com1, com2;
+ struct pc_keyboard keyboard;
+};
diff -Nru LinuxBIOSv2-2700/src/superio/winbond/w83977f/Config.lb LinuxBIOSv2-2700-w83977f/src/superio/winbond/w83977f/Config.lb
--- LinuxBIOSv2-2700/src/superio/winbond/w83977f/Config.lb 1970-01-01 05:00:00.000000000 +0500
+++ LinuxBIOSv2-2700-w83977f/src/superio/winbond/w83977f/Config.lb 2007-06-04 18:01:14.000000000 +0600
@@ -0,0 +1,22 @@
+##
+## This file is part of the LinuxBIOS project.
+##
+## Copyright (C) 2007 Nikolay Petukhov <[EMAIL PROTECTED]>
+##
+## This program is free software; you can redistribute it and/or modify
+## it under the terms of the GNU General Public License as published by
+## the Free Software Foundation; either version 2 of the License, or
+## (at your option) any later version.
+##
+## This program is distributed in the hope that it will be useful,
+## but WITHOUT ANY WARRANTY; without even the implied warranty of
+## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+## GNU General Public License for more details.
+##
+## You should have received a copy of the GNU General Public License
+## along with this program; if not, write to the Free Software
+## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+##
+
+config chip.h
+object superio.o
diff -Nru LinuxBIOSv2-2700/src/superio/winbond/w83977f/superio.c LinuxBIOSv2-2700-w83977f/src/superio/winbond/w83977f/superio.c
--- LinuxBIOSv2-2700/src/superio/winbond/w83977f/superio.c 1970-01-01 05:00:00.000000000 +0500
+++ LinuxBIOSv2-2700-w83977f/src/superio/winbond/w83977f/superio.c 2007-06-04 11:34:12.000000000 +0600
@@ -0,0 +1,122 @@
+/*
+ * This file is part of the LinuxBIOS project.
+ *
+ * Copyright (C) 2007 Nikolay Petukhov <[EMAIL PROTECTED]>
+ * Adapted from w83977tf
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <arch/io.h>
+#include <device/device.h>
+#include <device/pnp.h>
+#include <console/console.h>
+#include <string.h>
+#include <bitops.h>
+#include <uart8250.h>
+#include <pc80/keyboard.h>
+#include "chip.h"
+#include "w83977f.h"
+
+static void w83977f_enter_ext_func_mode(device_t dev)
+{
+ outb(0x87, dev->path.u.pnp.port);
+ outb(0x87, dev->path.u.pnp.port);
+}
+static void w83977f_exit_ext_func_mode(device_t dev)
+{
+ outb(0xaa, dev->path.u.pnp.port);
+}
+
+static void w83977f_init(device_t dev)
+{
+ struct superio_winbond_w83977f_config *conf;
+ struct resource *res0, *res1;
+ /* Wishlist handle well known programming interfaces more
+ * generically.
+ */
+ if (!dev->enabled) {
+ return;
+ }
+ conf = dev->chip_info;
+ switch(dev->path.u.pnp.device) {
+ case W83977F_SP1:
+ res0 = find_resource(dev, PNP_IDX_IO0);
+ init_uart8250(res0->base, &conf->com1);
+ break;
+ case W83977F_SP2:
+ res0 = find_resource(dev, PNP_IDX_IO0);
+ init_uart8250(res0->base, &conf->com2);
+ break;
+ case W83977F_KBC:
+ res0 = find_resource(dev, PNP_IDX_IO0);
+ res1 = find_resource(dev, PNP_IDX_IO1);
+ init_pc_keyboard(res0->base, res1->base, &conf->keyboard);
+ break;
+ }
+}
+
+static void w83977f_set_resources(device_t dev)
+{
+ w83977f_enter_ext_func_mode(dev);
+ pnp_set_resources(dev);
+ w83977f_exit_ext_func_mode(dev);
+}
+
+static void w83977f_enable_resources(device_t dev)
+{
+ w83977f_enter_ext_func_mode(dev);
+ pnp_enable_resources(dev);
+ w83977f_exit_ext_func_mode(dev);
+}
+
+static void w83977f_enable(device_t dev)
+{
+ w83977f_enter_ext_func_mode(dev);
+ pnp_enable(dev);
+ w83977f_exit_ext_func_mode(dev);
+}
+
+
+static struct device_operations ops = {
+ .read_resources = pnp_read_resources,
+ .set_resources = w83977f_set_resources,
+ .enable_resources = w83977f_enable_resources,
+ .enable = w83977f_enable,
+ .init = w83977f_init,
+};
+
+static struct pnp_info pnp_dev_info[] = {
+ { &ops, W83977F_FDC, PNP_IO0 | PNP_IRQ0 | PNP_DRQ0, { 0x7f8, 0 }, },
+ { &ops, W83977F_PP, PNP_IO0 | PNP_IRQ0 | PNP_DRQ0, { 0x7f8, 0 }, },
+ { &ops, W83977F_SP1, PNP_IO0 | PNP_IRQ0, { 0x7f8, 0 }, },
+ { &ops, W83977F_SP2, PNP_IO0 | PNP_IRQ0, { 0x7f8, 0 }, },
+ { &ops, W83977F_RTC, PNP_IO0 | PNP_IRQ0, { 0x7f8, 0 }, },
+ { &ops, W83977F_KBC, PNP_IO0 | PNP_IO1 | PNP_IRQ0 | PNP_IRQ1, { 0x7f8, 0 }, { 0x7f8, 0x0}, },
+ { &ops, W83977F_IR, PNP_IO0 | PNP_IRQ0, { 0x7f8, 0 }, },
+ { &ops, W83977F_GPIO1, PNP_IO0, { 0x7f8, 0 }, },
+ { &ops, W83977F_GPIO2, PNP_IO0, { 0x7f8, 0 }, },
+};
+
+static void enable_dev(device_t dev)
+{
+ pnp_enable_devices(dev, &ops,
+ sizeof(pnp_dev_info)/sizeof(pnp_dev_info[0]), pnp_dev_info);
+}
+
+struct chip_operations superio_winbond_w83977f_ops = {
+ CHIP_NAME("Winbond W83977F-A Super I/O")
+ .enable_dev = enable_dev,
+};
diff -Nru LinuxBIOSv2-2700/src/superio/winbond/w83977f/w83977f_early_serial.c LinuxBIOSv2-2700-w83977f/src/superio/winbond/w83977f/w83977f_early_serial.c
--- LinuxBIOSv2-2700/src/superio/winbond/w83977f/w83977f_early_serial.c 1970-01-01 05:00:00.000000000 +0500
+++ LinuxBIOSv2-2700-w83977f/src/superio/winbond/w83977f/w83977f_early_serial.c 2007-06-04 17:58:56.000000000 +0600
@@ -0,0 +1,46 @@
+/*
+ * This file is part of the LinuxBIOS project.
+ *
+ * Copyright (C) 2007 Nikolay Petukhov <[EMAIL PROTECTED]>
+ * Adapted from w83977tf
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <arch/romcc_io.h>
+#include "w83977f.h"
+
+static inline void pnp_enter_ext_func_mode(device_t dev)
+{
+ unsigned int port = dev >> 8;
+ outb(0x87, port);
+ outb(0x87, port);
+}
+
+static void pnp_exit_ext_func_mode(device_t dev)
+{
+ unsigned int port = dev >> 8;
+ outb(0xaa, port);
+}
+
+static void w83977f_enable_serial(device_t dev, unsigned int iobase)
+{
+ pnp_enter_ext_func_mode(dev);
+ pnp_set_logical_device(dev);
+ pnp_set_enable(dev, 0);
+ pnp_set_iobase(dev, PNP_IDX_IO0, iobase);
+ pnp_set_enable(dev, 1);
+ pnp_exit_ext_func_mode(dev);
+}
diff -Nru LinuxBIOSv2-2700/src/superio/winbond/w83977f/w83977f.h LinuxBIOSv2-2700-w83977f/src/superio/winbond/w83977f/w83977f.h
--- LinuxBIOSv2-2700/src/superio/winbond/w83977f/w83977f.h 1970-01-01 05:00:00.000000000 +0500
+++ LinuxBIOSv2-2700-w83977f/src/superio/winbond/w83977f/w83977f.h 2007-06-04 17:59:18.000000000 +0600
@@ -0,0 +1,30 @@
+/*
+ * This file is part of the LinuxBIOS project.
+ *
+ * Copyright (C) 2007 Nikolay Petukhov <[EMAIL PROTECTED]>
+ * Adapted from w83977tf
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#define W83977F_FDC 0 /* Floppy */
+#define W83977F_PP 1 /* Parallel Port */
+#define W83977F_SP1 2 /* Com1 */
+#define W83977F_SP2 3 /* Com2 */
+#define W83977F_RTC 4 /* RTC */
+#define W83977F_KBC 5 /* Keyboard & Mouse */
+#define W83977F_IR 6 /* Infrared Port */
+#define W83977F_GPIO1 7 /* General Purpose I/O 1 */
+#define W83977F_GPIO2 8 /* General Purpose I/O 2 */
diff -Nru LinuxBIOSv2-2700-w83977f/src/mainboard/iei/juki_511p/auto.c LinuxBIOSv2-2700-juki/src/mainboard/iei/juki_511p/auto.c
--- LinuxBIOSv2-2700-w83977f/src/mainboard/iei/juki_511p/auto.c 1970-01-01 05:00:00.000000000 +0500
+++ LinuxBIOSv2-2700-juki/src/mainboard/iei/juki_511p/auto.c 2007-06-04 10:51:59.000000000 +0600
@@ -0,0 +1,60 @@
+/*
+ * This file is part of the LinuxBIOS project.
+ *
+ * Copyright (C) 2007 Nikolay Petukhov <[EMAIL PROTECTED]>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#define ASSEMBLY 1
+
+#include <stdint.h>
+#include <device/pci_def.h>
+#include <arch/io.h>
+#include <device/pnp_def.h>
+#include <arch/romcc_io.h>
+#include <arch/hlt.h>
+#include "pc80/serial.c"
+#include "arch/i386/lib/console.c"
+#include "ram/ramtest.c"
+#include "superio/winbond/w83977f/w83977f_early_serial.c"
+#include "cpu/x86/bist.h"
+#include "pc80/udelay_io.c"
+
+#define SERIAL_DEV PNP_DEV(0x3f0, W83977F_SP1)
+
+#include "northbridge/amd/gx1/raminit.c"
+
+static void main(unsigned long bist)
+{
+ /* Initialize the serial console. */
+ w83977f_enable_serial(SERIAL_DEV, TTYS0_BASE);
+
+ uart_init();
+ console_init();
+
+ /* Halt if there was a built in self test failure. */
+ report_bist_failure(bist);
+
+ /* Disable Watchdog Timer. */
+ inb(0x043);
+ inb(0x843);
+
+ /* Initialize RAM. */
+ sdram_init();
+
+ /* Check RAM. */
+ /* ram_check(0x00000000, 640 * 1024); */
+}
diff -Nru LinuxBIOSv2-2700-w83977f/src/mainboard/iei/juki_511p/chip.h LinuxBIOSv2-2700-juki/src/mainboard/iei/juki_511p/chip.h
--- LinuxBIOSv2-2700-w83977f/src/mainboard/iei/juki_511p/chip.h 1970-01-01 05:00:00.000000000 +0500
+++ LinuxBIOSv2-2700-juki/src/mainboard/iei/juki_511p/chip.h 2007-06-04 10:11:11.000000000 +0600
@@ -0,0 +1,25 @@
+/*
+ * This file is part of the LinuxBIOS project.
+ *
+ * Copyright (C) 2007 Nikolay Petukhov <[EMAIL PROTECTED]>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+extern struct chip_operations mainboard_iei_juki_511p_ops;
+
+struct mainboard_iei_juki_511p_config {
+ int nothing;
+};
diff -Nru LinuxBIOSv2-2700-w83977f/src/mainboard/iei/juki_511p/cmos.layout LinuxBIOSv2-2700-juki/src/mainboard/iei/juki_511p/cmos.layout
--- LinuxBIOSv2-2700-w83977f/src/mainboard/iei/juki_511p/cmos.layout 1970-01-01 05:00:00.000000000 +0500
+++ LinuxBIOSv2-2700-juki/src/mainboard/iei/juki_511p/cmos.layout 2007-06-04 10:00:12.000000000 +0600
@@ -0,0 +1,73 @@
+entries
+
+#start-bit length config config-ID name
+#0 8 r 0 seconds
+#8 8 r 0 alarm_seconds
+#16 8 r 0 minutes
+#24 8 r 0 alarm_minutes
+#32 8 r 0 hours
+#40 8 r 0 alarm_hours
+#48 8 r 0 day_of_week
+#56 8 r 0 day_of_month
+#64 8 r 0 month
+#72 8 r 0 year
+#80 4 r 0 rate_select
+#84 3 r 0 REF_Clock
+#87 1 r 0 UIP
+#88 1 r 0 auto_switch_DST
+#89 1 r 0 24_hour_mode
+#90 1 r 0 binary_values_enable
+#91 1 r 0 square-wave_out_enable
+#92 1 r 0 update_finished_enable
+#93 1 r 0 alarm_interrupt_enable
+#94 1 r 0 periodic_interrupt_enable
+#95 1 r 0 disable_clock_updates
+#96 288 r 0 temporary_filler
+0 384 r 0 reserved_memory
+384 1 e 4 boot_option
+385 1 e 4 last_boot
+386 1 e 1 ECC_memory
+388 4 r 0 reboot_bits
+392 3 e 5 baud_rate
+400 1 e 1 power_on_after_fail
+412 4 e 6 debug_level
+416 4 e 7 boot_first
+420 4 e 7 boot_second
+424 4 e 7 boot_third
+428 4 h 0 boot_index
+432 8 h 0 boot_countdown
+1008 16 h 0 check_sum
+
+enumerations
+
+#ID value text
+1 0 Disable
+1 1 Enable
+2 0 Enable
+2 1 Disable
+4 0 Fallback
+4 1 Normal
+5 0 115200
+5 1 57600
+5 2 38400
+5 3 19200
+5 4 9600
+5 5 4800
+5 6 2400
+5 7 1200
+6 6 Notice
+6 7 Info
+6 8 Debug
+6 9 Spew
+7 0 Network
+7 1 HDD
+7 2 Floppy
+7 8 Fallback_Network
+7 9 Fallback_HDD
+7 10 Fallback_Floppy
+#7 3 ROM
+
+checksums
+
+checksum 392 1007 1008
+
diff -Nru LinuxBIOSv2-2700-w83977f/src/mainboard/iei/juki_511p/Config.lb LinuxBIOSv2-2700-juki/src/mainboard/iei/juki_511p/Config.lb
--- LinuxBIOSv2-2700-w83977f/src/mainboard/iei/juki_511p/Config.lb 1970-01-01 05:00:00.000000000 +0500
+++ LinuxBIOSv2-2700-juki/src/mainboard/iei/juki_511p/Config.lb 2007-06-04 11:04:13.000000000 +0600
@@ -0,0 +1,167 @@
+##
+## Compute the location and size of where this firmware image
+## (linuxBIOS plus bootloader) will live in the boot rom chip.
+##
+default ROM_SIZE = 256 * 1024
+default ROM_SECTION_SIZE = ROM_SIZE
+default ROM_SECTION_OFFSET = 0
+
+##
+## Compute the start location and size size of
+## The linuxBIOS bootloader.
+##
+default PAYLOAD_SIZE = ( ROM_SECTION_SIZE - ROM_IMAGE_SIZE )
+default CONFIG_ROM_PAYLOAD_START = (0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1)
+
+##
+## Compute where this copy of linuxBIOS will start in the boot rom
+##
+default _ROMBASE = ( CONFIG_ROM_PAYLOAD_START + PAYLOAD_SIZE )
+
+##
+## Compute a range of ROM that can cached to speed up linuxBIOS,
+## execution speed.
+##
+## XIP_ROM_SIZE must be a power of 2.
+## XIP_ROM_BASE must be a multiple of XIP_ROM_SIZE
+##
+default XIP_ROM_SIZE=65536
+default XIP_ROM_BASE = ( _ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE )
+
+##
+## Set all of the defaults for an x86 architecture
+##
+
+arch i386 end
+
+##
+## Build the objects we have code for in this directory.
+##
+
+driver mainboard.o
+
+if HAVE_PIRQ_TABLE object irq_tables.o end
+#object reset.o
+
+##
+## Romcc output
+##
+makerule ./failover.E
+ depends "$(MAINBOARD)/failover.c ./romcc"
+ action "./romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
+end
+
+makerule ./failover.inc
+ depends "$(MAINBOARD)/failover.c ./romcc"
+ action "./romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
+end
+
+makerule ./auto.E
+ depends "$(MAINBOARD)/auto.c option_table.h ./romcc"
+ action "./romcc -E -mcpu=i386 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+end
+makerule ./auto.inc
+ depends "$(MAINBOARD)/auto.c option_table.h ./romcc"
+ action "./romcc -mcpu=i386 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+end
+
+##
+## Build our 16 bit and 32 bit linuxBIOS entry code
+##
+mainboardinit cpu/x86/16bit/entry16.inc
+mainboardinit cpu/x86/32bit/entry32.inc
+ldscript /cpu/x86/16bit/entry16.lds
+ldscript /cpu/x86/32bit/entry32.lds
+
+##
+## Build our reset vector (This is where linuxBIOS is entered)
+##
+mainboardinit cpu/x86/16bit/reset16.inc
+ldscript /cpu/x86/16bit/reset16.lds
+
+### Should this be in the northbridge code?
+mainboardinit arch/i386/lib/cpu_reset.inc
+
+##
+## Include an id string (For safe flashing)
+##
+mainboardinit arch/i386/lib/id.inc
+ldscript /arch/i386/lib/id.lds
+
+###
+### O.k. We aren't just an intermediary anymore!
+###
+
+##
+## Setup RAM
+##
+mainboardinit cpu/x86/fpu/enable_fpu.inc
+mainboardinit cpu/amd/model_gx1/cpu_setup.inc
+mainboardinit cpu/amd/model_gx1/gx_setup.inc
+mainboardinit ./auto.inc
+
+##
+## Include the secondary Configuration files
+##
+#dir /pc80
+#config chip.h
+
+chip northbridge/amd/gx1
+ device pci_domain 0 on
+ device pci 0.0 on end
+ chip southbridge/amd/cs5530
+
+ device pci 12.0 on
+ chip superio/winbond/w83977f
+ device pnp 3f0.0 on # FDC
+ irq 0x70 = 6
+ end
+ device pnp 3f0.1 on # Parallel Port
+ io 0x60 = 0x378
+ irq 0x70 = 7
+ end
+ device pnp 3f0.2 on # COM1
+ io 0x60 = 0x3f8
+ irq 0x70 = 4
+ end
+ register "com1" = "{115200}"
+ device pnp 3f0.3 on # COM2
+ io 0x60 = 0x2f8
+ irq 0x70 = 3
+ end
+ register "com2" = "{115200}"
+ device pnp 3f0.4 on # RTC
+ io 0x60 = 0x070
+ irq 0x70 = 8
+ end
+ device pnp 3f0.5 on # Keyboard
+ io 0x60 = 0x60
+ io 0x62 = 0x64
+ irq 0x70 = 1 # int 1 for PS/2 keyboard
+ irq 0x72 = 12 # int 12 for PS/2 mouse
+ end
+ device pnp 3f0.6 off # IR
+ end
+ device pnp 3f0.7 off # GPIO1
+ end
+ device pnp 3f0.8 off # GPIO
+ end
+ end
+ device pci 12.1 on end # SMI
+ device pci 12.2 on end # IDE
+ device pci 12.3 on end # Audio
+ device pci 12.4 on end # VGA onboard
+
+ end
+
+ device pci 0e.0 on end # ETH0
+ device pci 13.0 on end # USB
+
+ end
+ end
+
+ chip cpu/amd/model_gx1
+ end
+
+end
+
diff -Nru LinuxBIOSv2-2700-w83977f/src/mainboard/iei/juki_511p/failover.c LinuxBIOSv2-2700-juki/src/mainboard/iei/juki_511p/failover.c
--- LinuxBIOSv2-2700-w83977f/src/mainboard/iei/juki_511p/failover.c 1970-01-01 05:00:00.000000000 +0500
+++ LinuxBIOSv2-2700-juki/src/mainboard/iei/juki_511p/failover.c 2007-06-04 10:00:12.000000000 +0600
@@ -0,0 +1,53 @@
+/*
+ * This file is part of the LinuxBIOS project.
+ *
+ * Copyright (C) 2007 Nikolay Petukhov <[EMAIL PROTECTED]>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#define ASSEMBLY 1
+
+#include <stdint.h>
+#include <device/pci_def.h>
+#include <device/pci_ids.h>
+#include <arch/io.h>
+#include "arch/romcc_io.h"
+#include "pc80/mc146818rtc_early.c"
+
+static unsigned long main(unsigned long bist)
+{
+ /* This is the primary cpu how should I boot? */
+ if (do_normal_boot()) {
+ goto normal_image;
+ }
+ else {
+ goto fallback_image;
+ }
+ normal_image:
+ asm volatile ("jmp __normal_image"
+ : /* outputs */
+ : "a" (bist) /* inputs */
+ : /* clobbers */
+ );
+ cpu_reset:
+ asm volatile ("jmp __cpu_reset"
+ : /* outputs */
+ : "a"(bist) /* inputs */
+ : /* clobbers */
+ );
+ fallback_image:
+ return bist;
+}
diff -Nru LinuxBIOSv2-2700-w83977f/src/mainboard/iei/juki_511p/irq_tables.c LinuxBIOSv2-2700-juki/src/mainboard/iei/juki_511p/irq_tables.c
--- LinuxBIOSv2-2700-w83977f/src/mainboard/iei/juki_511p/irq_tables.c 1970-01-01 05:00:00.000000000 +0500
+++ LinuxBIOSv2-2700-juki/src/mainboard/iei/juki_511p/irq_tables.c 2007-06-04 17:54:00.000000000 +0600
@@ -0,0 +1,102 @@
+/*
+ * This file is part of the LinuxBIOS project.
+ *
+ * Copyright (C) 2007 Nikolay Petukhov <[EMAIL PROTECTED]>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+#include <arch/pirq_routing.h>
+
+#define IRQ_BITMAP_LINK0 0x0800 /* chipset's INTA# input should be routed to IRQ11 */
+#define IRQ_BITMAP_LINK1 0x0400 /* chipset's INTB# input should be routed to IRQ10 */
+#define IRQ_BITMAP_LINK2 0x0000 /* chipset's INTC# input should be routed to nothing (disabled) */
+#define IRQ_BITMAP_LINK3 0x0000 /* chipset's INTD# input should be routed to nothing (disabled) */
+
+const struct irq_routing_table intel_irq_routing_table = {
+ PIRQ_SIGNATURE, /* u32 signature */
+ PIRQ_VERSION, /* u16 version */
+ 32+16*2, /* There can be total 2 devices on the bus */
+ 0x00, /* Where the interrupt router lies (bus) */
+ (0x12<<3)|0x0, /* Where the interrupt router lies (dev) */
+ 0xc00, /* IRQs devoted exclusively to PCI usage */
+ 0x1078, /* Vendor */
+ 0x2, /* Device */
+ 0, /* Crap (miniport) */
+ { 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 }, /* u8 rfu[11] */
+ 0x57, /* u8 checksum. This has to be set to some
+ value that would give 0 after the sum of all
+ bytes for this structure (including checksum) */
+
+ .slots = {
+ [0] = {
+ .slot = 0x0, /* should be 0 when it is no real slot. My device is soldered */
+ .bus = 0x00,
+ .devfn = (0x13<<3)|0x0, /* 0x13 is my USB OHCI */
+ .irq = {
+ [0] = { /* <-- 0 means this is INTA# output from the device or slot */
+ .link = 0x01, /* 0x01 means its connected to INTA# input at chipset */
+ .bitmap = IRQ_BITMAP_LINK0
+ },
+ [1] = { /* <-- 1 means this is INTB# output from the device or slot */
+ .link = 0x02, /* 0x02 means its connected to INTB# input at chipset */
+ .bitmap = IRQ_BITMAP_LINK1
+ },
+ [2] = { /* <-- 2 means this is INTC# output from the device or slot */
+ .link = 0x03, /* 0x03 means its connected to INTC# input at chipset */
+ .bitmap = IRQ_BITMAP_LINK2
+ },
+ [3] = { /* <-- 3 means this is INTD# output from the device or slot */
+ .link = 0x04, /* 0x04 means its connected to INTD# input at chipset */
+ .bitmap = IRQ_BITMAP_LINK3
+ }
+ }
+ },
+
+ [1] = {
+ .slot = 0x0, /* means also "on board" */
+ .bus = 0x00,
+ .devfn = (0x0e<<3)|0x0, /* 0x0e is my Realtek Network device */
+ .irq = {
+ [0] = { /* <-- 0 means this is INTA# output from the device or slot */
+ .link = 0x02, /* 0x02 means its connected to INTB# input at chipset */
+ .bitmap = IRQ_BITMAP_LINK1
+ },
+ [1] = { /* <-- 1 means this is INTB# output from the device or slot */
+ .link = 0x03, /* 0x03 means its connected to INTC# input at chipset */
+ .bitmap = IRQ_BITMAP_LINK2
+ },
+ [2] = { /* <-- 2 means this is INTC# output from the device or slot */
+ .link = 0x04, /* 0x04 means its connected to INTD# input at chipset */
+ .bitmap = IRQ_BITMAP_LINK3
+ },
+ [3] = { /* <-- 3 means this is INTD# output from the device or slot */
+ .link = 0x01, /* 0x01 means its connected to INTA# input at chipset */
+ .bitmap = IRQ_BITMAP_LINK0
+ }
+ }
+ }
+ }
+};
+
+/**
+ * Copy the IRQ routing table to memory.
+ *
+ * @param addr Destination address (between 0xF0000...0x100000).
+ * @return The end address of the pirq routing table in memory.
+ **/
+unsigned long write_pirq_routing_table(unsigned long addr)
+{
+ return copy_pirq_routing_table(addr);
+}
diff -Nru LinuxBIOSv2-2700-w83977f/src/mainboard/iei/juki_511p/mainboard.c LinuxBIOSv2-2700-juki/src/mainboard/iei/juki_511p/mainboard.c
--- LinuxBIOSv2-2700-w83977f/src/mainboard/iei/juki_511p/mainboard.c 1970-01-01 05:00:00.000000000 +0500
+++ LinuxBIOSv2-2700-juki/src/mainboard/iei/juki_511p/mainboard.c 2007-06-04 10:11:29.000000000 +0600
@@ -0,0 +1,31 @@
+/*
+ * This file is part of the LinuxBIOS project.
+ *
+ * Copyright (C) 2007 Nikolay Petukhov <[EMAIL PROTECTED]>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <console/console.h>
+#include <device/device.h>
+#include <device/pci.h>
+#include <device/pci_ids.h>
+#include <device/pci_ops.h>
+#include <arch/io.h>
+#include "chip.h"
+
+struct chip_operations mainboard_iei_juki_511p_ops = {
+ CHIP_NAME("IEI JUKI-511P Mainboard")
+};
diff -Nru LinuxBIOSv2-2700-w83977f/src/mainboard/iei/juki_511p/Options.lb LinuxBIOSv2-2700-juki/src/mainboard/iei/juki_511p/Options.lb
--- LinuxBIOSv2-2700-w83977f/src/mainboard/iei/juki_511p/Options.lb 1970-01-01 05:00:00.000000000 +0500
+++ LinuxBIOSv2-2700-juki/src/mainboard/iei/juki_511p/Options.lb 2007-06-04 10:00:12.000000000 +0600
@@ -0,0 +1,147 @@
+uses HAVE_MP_TABLE
+uses HAVE_PIRQ_TABLE
+uses USE_FALLBACK_IMAGE
+uses HAVE_FALLBACK_BOOT
+uses HAVE_HARD_RESET
+uses CONFIG_UDELAY_IO
+uses HAVE_OPTION_TABLE
+uses USE_OPTION_TABLE
+uses CONFIG_COMPRESS
+uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
+uses CONFIG_COMPRESSED_PAYLOAD_LZMA
+uses CONFIG_PRECOMPRESSED_PAYLOAD
+uses CONFIG_ROM_PAYLOAD
+uses IRQ_SLOT_COUNT
+uses MAINBOARD
+uses MAINBOARD_VENDOR
+uses MAINBOARD_PART_NUMBER
+uses LINUXBIOS_EXTRA_VERSION
+uses ARCH
+uses FALLBACK_SIZE
+uses STACK_SIZE
+uses HEAP_SIZE
+uses ROM_SIZE
+uses ROM_SECTION_SIZE
+uses ROM_IMAGE_SIZE
+uses ROM_SECTION_SIZE
+uses ROM_SECTION_OFFSET
+uses CONFIG_ROM_PAYLOAD_START
+uses PAYLOAD_SIZE
+uses _ROMBASE
+uses _RAMBASE
+uses XIP_ROM_SIZE
+uses XIP_ROM_BASE
+uses HAVE_MP_TABLE
+uses CROSS_COMPILE
+uses CC
+uses HOSTCC
+
+uses OBJCOPY
+
+uses CONFIG_CONSOLE_SERIAL8250
+uses DEFAULT_CONSOLE_LOGLEVEL
+uses MAXIMUM_CONSOLE_LOGLEVEL
+
+uses TTYS0_BAUD
+uses TTYS0_BASE
+uses TTYS0_LCS
+
+
+## ROM_SIZE is the size of boot ROM that this board will use.
+default ROM_SIZE = 256*1024
+
+###
+### Build options
+###
+
+##
+## Build code for the fallback boot
+##
+default HAVE_FALLBACK_BOOT=1
+
+##
+## no MP table
+##
+default HAVE_MP_TABLE=0
+
+##
+## Build code to reset the motherboard from linuxBIOS
+##
+default HAVE_HARD_RESET=0
+
+default CONFIG_UDELAY_IO=1
+##
+## Build code to export a programmable irq routing table
+##
+default HAVE_PIRQ_TABLE=0
+default IRQ_SLOT_COUNT=2
+#object irq_tables.o
+
+##
+## Build code to export a CMOS option table
+##
+default HAVE_OPTION_TABLE=0
+
+###
+### LinuxBIOS layout values
+###
+
+## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy.
+default ROM_IMAGE_SIZE = 65536
+default FALLBACK_SIZE = 131072
+
+##
+## Use a small 8K stack
+##
+default STACK_SIZE=0x2000
+
+##
+## Use a small 16K heap
+##
+default HEAP_SIZE=0x4000
+
+##
+## Only use the option table in a normal image
+##
+#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
+default USE_OPTION_TABLE = 0
+
+default _RAMBASE = 0x00004000
+
+default CONFIG_ROM_PAYLOAD = 1
+
+##
+## The Serial Console
+##
+
+# To Enable the Serial Console
+default CONFIG_CONSOLE_SERIAL8250=1
+default DEFAULT_CONSOLE_LOGLEVEL=8
+default MAXIMUM_CONSOLE_LOGLEVEL=8
+
+## Select the serial console baud rate
+default TTYS0_BAUD=115200
+#default TTYS0_BAUD=57600
+#default TTYS0_BAUD=38400
+#default TTYS0_BAUD=19200
+#default TTYS0_BAUD=9600
+#default TTYS0_BAUD=4800
+#default TTYS0_BAUD=2400
+#default TTYS0_BAUD=1200
+
+# Select the serial console base port
+default TTYS0_BASE=0x3f8
+
+# Select the serial protocol
+# This defaults to 8 data bits, 1 stop bit, and no parity
+default TTYS0_LCS=0x3
+
+##
+## The default compiler
+##
+default CROSS_COMPILE=""
+default CC="$(CROSS_COMPILE)gcc -m32"
+default HOSTCC="gcc"
+
+end
+
diff -Nru LinuxBIOSv2-2700-w83977f/targets/iei/juki_511p/Config.lb LinuxBIOSv2-2700-juki/targets/iei/juki_511p/Config.lb
--- LinuxBIOSv2-2700-w83977f/targets/iei/juki_511p/Config.lb 1970-01-01 05:00:00.000000000 +0500
+++ LinuxBIOSv2-2700-juki/targets/iei/juki_511p/Config.lb 2007-06-04 11:02:55.000000000 +0600
@@ -0,0 +1,40 @@
+##
+## This file is part of the LinuxBIOS project.
+##
+## Copyright (C) 2007 Nikolay Petukhov <[EMAIL PROTECTED]>
+##
+## This program is free software; you can redistribute it and/or modify
+## it under the terms of the GNU General Public License as published by
+## the Free Software Foundation; either version 2 of the License, or
+## (at your option) any later version.
+##
+## This program is distributed in the hope that it will be useful,
+## but WITHOUT ANY WARRANTY; without even the implied warranty of
+## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+## GNU General Public License for more details.
+##
+## You should have received a copy of the GNU General Public License
+## along with this program; if not, write to the Free Software
+## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+##
+
+# Config file for the IEI juki511_p motherboard
+# This will make a target directory of juki_511p
+
+target juki_511p
+mainboard iei/juki_511p
+
+option ROM_SIZE=256*1024
+
+option HAVE_PIRQ_TABLE=1
+
+option CONFIG_COMPRESS=0
+option CONFIG_PRECOMPRESSED_PAYLOAD=0
+
+romimage "image"
+ option ROM_IMAGE_SIZE=64*1024
+ option LINUXBIOS_EXTRA_VERSION="-filo"
+ payload ../../filo.elf
+end
+
+buildrom ./linuxbios.rom ROM_SIZE "image"
--
linuxbios mailing list
[email protected]
http://www.linuxbios.org/mailman/listinfo/linuxbios
