This adds probing for almost all recent (since 1999) ITE Super I/O chips
to probe_superio. Not much of the configuration is dumped, however I did
verify against all ITE datasheets (including those not available any
more) that the probing was non-destructive.
More information can be extracted easily, however this needs loads of
datasheet surfing.
Signed-off-by: Carl-Daniel Hailfinger <[EMAIL PROTECTED]>
--- LinuxBIOSv2/util/probe_superio/probe_superio.c (Revision 2744)
+++ LinuxBIOSv2/util/probe_superio/probe_superio.c (Arbeitskopie)
@@ -3,6 +3,7 @@
*
* Copyright (C) 2006 Ronald Minnich <[EMAIL PROTECTED]>
* Copyright (C) 2006 coresystems GmbH <[EMAIL PROTECTED]>
+ * Copyright (C) 2007 Carl-Daniel Hailfinger
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
@@ -32,11 +33,16 @@
* if we need this.
*/
-unsigned char regval(unsigned short port, unsigned short reg) {
+unsigned char regval(unsigned short port, unsigned char reg) {
outb(reg, port);
return inb(port+1);
}
+void regwrite(unsigned short port, unsigned char reg, unsigned char val) {
+ outb(reg, port);
+ outb(val, port+1);
+}
+
void
dump_ns8374(unsigned short port) {
printf("Enables: 21=%02x, 22=%02x, 23=%02x, 24=%02x, 26=%02x\n",
@@ -46,15 +52,13 @@
/* check COM1. This is all we care about at present. */
printf("COM 1 is Globally %s\n", regval(port,0x26)&8 ? "disabled" :
"enabled");
/* select com1 */
- outb(0x7, port);
- outb(3, port+1);
+ regwrite(port, 0x07, 0x03);
printf("COM 1 is locally %s\n", regval(port, 0x30) & 1 ? "enabled" :
"disabled");
printf("COM1 60=%02x, 61=%02x, 70=%02x, 71=%02x, 74=%02x, 75=%02x,
f0=%02x\n",
regval(port, 0x60), regval(port, 0x61), regval(port, 0x70),
regval(port, 0x71),
regval(port, 0x74), regval(port, 0x75), regval(port, 0xf0));
/* select gpio */
- outb(0x7, port);
- outb(7, port+1);
+ regwrite(port, 0x07, 0x07);
printf("GPIO is %s\n", regval(port, 0x30) & 1 ? "enabled" : "disabled");
printf("GPIO 60=%02x, 61=%02x, 70=%02x, 71=%02x, 74=%02x, 75=%02x,
f0=%02x\n",
regval(port, 0x60), regval(port, 0x61), regval(port, 0x70),
regval(port, 0x71),
@@ -85,38 +89,33 @@
printf("2b=%02x\n", regval(port, 0x2b));
/* select UART 1 */
- outb(0x07, port);
- outb(0x01, port+1);
+ regwrite(port, 0x07, 0x01);
printf("UART1 is %s\n", regval(port, 0x30) & 1 ? "enabled" :
"disabled");
printf("UART1 base=%02x%02x, irq=%02x, mode=%s\n",
regval(port, 0x60), regval(port, 0x61), regval(port,
0x70)&0x0f,
regval(port, 0xf0)&0x10 ? "RS485":"RS232");
/* select UART 2 */
- outb(0x07, port);
- outb(0x02, port+1);
+ regwrite(port, 0x07, 0x02);
printf("UART2 is %s\n", regval(port, 0x30) & 1 ? "enabled" :
"disabled");
printf("UART2 base=%02x%02x, irq=%02x, mode=%s\n",
regval(port, 0x60), regval(port, 0x61), regval(port,
0x70)&0x0f,
regval(port, 0xf0)&0x10 ? "RS485":"RS232");
/* select Parport */
- outb(0x07, port);
- outb(0x03, port+1);
+ regwrite(port, 0x07, 0x03);
printf("PARPORT is %s\n", regval(port, 0x30) & 1 ? "enabled" :
"disabled");
printf("PARPORT base=%02x%02x, irq=%02x\n",
regval(port, 0x60), regval(port, 0x61), regval(port,
0x70)&0x0f);
/* select hw monitor */
- outb(0x07, port);
- outb(0x04, port+1);
+ regwrite(port, 0x07, 0x04);
printf("HW monitor is %s\n", regval(port, 0x30) & 1 ? "enabled" :
"disabled");
printf("HW monitor base=%02x%02x, irq=%02x\n",
regval(port, 0x60), regval(port, 0x61), regval(port,
0x70)&0x0f);
/* select gpio */
- outb(0x07, port);
- outb(0x06, port+1);
+ regwrite(port, 0x07, 0x05);
printf("GPIO is %s\n", regval(port, 0x30) & 1 ? "enabled" : "disabled");
printf("GPIO 70=%02x, e0=%02x, e1=%02x, e2=%02x, e3=%02x, e4=%02x,
e5=%02x\n",
regval(port, 0x70), regval(port, 0xe0), regval(port, 0xe1),
regval(port, 0xe2),
@@ -130,7 +129,30 @@
}
+void
+dump_ite(unsigned short port, unsigned short id)
+{
+ int i;
+ printf ("ITE chip\n");
+ for (i=0x20; i<=0x24; i++)
+ printf("index %02x=%02x\n", i, regval(port, i));
+
+ switch(id) {
+ case 0x8702:
+ case 0x8705:
+ case 0x8710:
+ case 0x8712:
+ case 0x8716:
+ case 0x8718:
+ default:
+ break;
+ }
+ /* select UART 1 */
+ regwrite(port, 0x07, 0x01);
+ printf("UART1 is %s\n", regval(port, 0x30) & 1 ? "enabled" :
"disabled");
+}
+
void
probe_idregs_simple(unsigned short port){
unsigned char id;
@@ -167,9 +189,10 @@
void
probe_idregs_fintek(unsigned short port){
- unsigned int vid, did;
+ unsigned int vid, did, success = 0;
// Enable configuration sequence (Fintek uses this for example)
+ // Older ITE chips have the same enable sequence
outb(0x87, port);
outb(0x87, port);
@@ -185,13 +208,10 @@
}
did = inb(port+1);
- outb(0x21, port);
- did = did|(inb(port+1)<<8);
+ did = did|(regval(port, 0x21)<<8);
- outb(0x23, port);
- vid = inb(port+1);
- outb(0x24, port);
- vid = vid|(inb(port+1)<<8);
+ vid = regval(port, 0x23);
+ vid = vid|(regval(port, 0x24)<<8);
printf("SuperIO found at 0x%02x: vid=0x%04x/did=0x%04x\n", port, vid,
did);
@@ -199,23 +219,103 @@
return;
// printf("%s\n", familyid[id]);
+ switch(did) {
+ case 0x1087: // reversed for ITE8710
+ success = 1;
+ dump_ite(port, ((did & 0xff) << 8) | ((did & 0xff00) >>
8));
+ // disable configuration
+ regwrite(port, 0x02, 0x02);
+ break;
+ default:
+ break;
+ }
switch(vid) {
case 0x3419:
+ success = 1;
dump_fintek(port, did);
break;
default:
- printf("no dump for 0x%04x/0x%04x\n", vid, did);
break;
}
+ if (!success)
+ printf("no dump for vid 0x%04x, did 0x%04x\n", vid, did);
- // disable configuration
+ // disable configuration (for Fintek, doesn't hurt ITE)
outb(0xaa, port);
}
void
+probe_idregs_ite(unsigned short port){
+ unsigned int id, chipver;
+
+ // Enable configuration sequence (ITE uses this for newer IT87[012]x)
+ // IT871[01] uses 0x87, 0x87 -> fintek detection should handle it
+ // IT8761 uses 0x87, 0x61, 0x55, 0x55/0xaa
+ // IT86xx series uses different ports
+ // IT8661 uses 0x86, 0x61, 0x55/0xaa, 0x55/0xaa and 32 more writes
+ // IT8673 uses 0x86, 0x80, 0x55/0xaa, 0x55/0xaa and 32 more writes
+ outb(0x87, port);
+ outb(0x01, port);
+ outb(0x55, port);
+ if (port == 0x2e)
+ outb(0x55, port);
+ else
+ outb(0xAA, port);
+
+ // Read Chip ID Byte 1
+ id = regval(port, 0x20);
+ if (id != 0x87) {
+ if (inb(port) == 0xff )
+ printf ("No SuperIO chip found at 0x%04x\n", port);
+ else
+ printf("probing 0x%04x, failed (0x%02x), data returns
0x%02x\n",
+ port, inb(port), inb(port+1));
+ return;
+ }
+
+ id <<= 8;
+
+ // Read Chip ID Byte 2
+ id |= regval(port, 0x21);
+
+ // Read Chip Version, only bit 3..0 for all IT87xx
+ chipver = regval(port, 0x22) & 0x0f;
+
+ /* ID Mapping Table
+ unknown -> IT8711 (no datasheet)
+ unknown -> IT8722 (no datasheet)
+ 0x8702 -> IT8702
+ 0x8705 -> IT8700 or IT8705
+ 0x8710 -> IT8710
+ 0x8712 -> IT8712
+ 0x8716 -> IT8716 or IT8726 (identical except CPU voltage control)
+ 0x8718 -> IT8718
+ */
+ printf("ITE? SuperIO found at 0x%02x: id=0x%04x, chipver=0x%01x\n",
+ port, id, chipver);
+
+ switch(id) {
+ case 0x8702:
+ case 0x8705:
+ case 0x8710: //pointless, IT8710 has different enable sequence
+ case 0x8712:
+ case 0x8716:
+ case 0x8718:
+ dump_ite(port, id);
+ break;
+ default:
+ printf("no dump for id 0x%04x\n", id);
+ break;
+ }
+ // disable configuration
+ regwrite(port, 0x02, 0x02);
+}
+
+void
probe_superio(unsigned short port) {
probe_idregs_simple(port);
probe_idregs_fintek(port);
+ probe_idregs_ite(port);
}
int
--
linuxbios mailing list
linuxbios@linuxbios.org
http://www.linuxbios.org/mailman/listinfo/linuxbios
