On Jan 9, 2008, at 5:35 PM, Timur Tabi wrote:

> Add file ucc_uart.c, a serial device driver for the Freescale  
> QUICCEngine.
> Update the Kconfig and Makefile accordingly.
>
> Signed-off-by: Timur Tabi <[EMAIL PROTECTED]>
> ---
> drivers/serial/Kconfig    |   10 +
> drivers/serial/Makefile   |    1 +
> drivers/serial/ucc_uart.c | 1507 ++++++++++++++++++++++++++++++++++++ 
> +++++++++
> 3 files changed, 1518 insertions(+), 0 deletions(-)
> create mode 100644 drivers/serial/ucc_uart.c
>


>
> diff --git a/drivers/serial/ucc_uart.c b/drivers/serial/ucc_uart.c
> new file mode 100644
> index 0000000..6fe4cfc
> --- /dev/null
> +++ b/drivers/serial/ucc_uart.c
> @@ -0,0 +1,1507 @@
> +/*
> + * Freescale QUICC Engine UART device driver
> + *
> + * Author: Timur Tabi <[EMAIL PROTECTED]>
> + *
> + * Copyright 2007 Freescale Semiconductor, Inc.  This file is  
> licensed under
> + * the terms of the GNU General Public License version 2.  This  
> program
> + * is licensed "as is" without any warranty of any kind, whether  
> express
> + * or implied.
> + *
> + * This driver adds support for UART devices via Freescale's QUICC  
> Engine
> + * found on some Freescale SOCs.
> + *
> + * If Soft-UART support is needed but not already present, then  
> this driver
> + * will request and upload the "Soft-UART" microcode upon probe.  The
> + * filename of the microcode should be fsl_qe_ucode_uart_X_YZ.bin,  
> where "X"
> + * is the name of the SOC (e.g. 8323), and YZ is the revision of  
> the SOC,
> + * (e.g. "11" for 1.1).
> + */
> +


what is the define for?  you commented all the others :)
>
> +#define UCC_WAIT_CLOSING 100
> +
> +struct ucc_uart_pram {
> +     struct ucc_slow_pram common;
> +     u8 res1[8];             /* reserved */
> +     __be16 maxidl;          /* Maximum idle chars */
> +     __be16 idlc;            /* temp idle counter */
> +     __be16 brkcr;           /* Break count register */
> +     __be16 parec;           /* receive parity error counter */
> +     __be16 frmec;           /* receive framing error counter */
> +     __be16 nosec;           /* receive noise counter */
> +     __be16 brkec;           /* receive break condition counter */
> +     __be16 brkln;           /* last received break length */
> +     __be16 uaddr[2];        /* UART address character 1 & 2 */
> +     __be16 rtemp;           /* Temp storage */
> +     __be16 toseq;           /* Transmit out of sequence char */
> +     __be16 cchars[8];       /* control characters 1-8 */
> +     __be16 rccm;            /* receive control character mask */
> +     __be16 rccr;            /* receive control character register */
> +     __be16 rlbc;            /* receive last break character */
> +     __be16 res2;            /* reserved */
> +     __be32 res3;            /* reserved, should be cleared */
> +     u8 res4;                /* reserved, should be cleared */
> +     u8 res5[3];             /* reserved, should be cleared */
> +     __be32 res6;            /* reserved, should be cleared */
> +     __be32 res7;            /* reserved, should be cleared */
> +     __be32 res8;            /* reserved, should be cleared */
> +     __be32 res9;            /* reserved, should be cleared */
> +     __be32 res10;           /* reserved, should be cleared */
> +     __be32 res11;           /* reserved, should be cleared */
> +     __be32 res12;           /* reserved, should be cleared */
> +     __be32 res13;           /* reserved, should be cleared */
> +/* The rest is for Soft-UART only */
> +     __be16 supsmr;          /* 0x90, Shadow UPSMR */
> +     __be16 res92;           /* 0x92, reserved, initialize to 0 */
> +     __be32 rx_state;        /* 0x94, RX state, initialize to 0 */
> +     __be32 rx_cnt;          /* 0x98, RX count, initialize to 0 */
> +     u8 rx_length;           /* 0x9C, Char length, set to 1+CL+PEN+1+SL */
> +     u8 rx_bitmark;          /* 0x9D, reserved, initialize to 0 */
> +     u8 rx_temp_dlst_qe;     /* 0x9E, reserved, initialize to 0 */
> +     u8 res14[0xBC - 0x9F];  /* reserved */
> +     __be32 dump_ptr;        /* 0xBC, Dump pointer */
> +     __be32 rx_frame_rem;    /* 0xC0, reserved, initialize to 0 */
> +     u8 rx_frame_rem_size;   /* 0xC4, reserved, initialize to 0 */
> +     u8 tx_mode;             /* 0xC5, mode, 0=AHDLC, 1=UART */
> +     u16 tx_state;           /* 0xC6, TX state */

__be16?

>
> +     u8 res15[0xD0 - 0xC8];  /* reserved */
> +     __be32 resD0;           /* 0xD0, reserved, initialize to 0 */
> +     u8 resD4;               /* 0xD4, reserved, initialize to 0 */
> +     __be16 resD5;           /* 0xD5, reserved, initialize to 0 */
> +} __attribute__ ((packed));
> +
>
>


> +/*
> + * Set the modem control lines
> + *
> + * We currently don't support setting modem control lines, but this  
> function
> + * needs to exist, otherwise the kernel will panic.
> + */
> +void qe_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
> +{
> +}

What's the issue w/support of this?  (maybe a comment related to why  
its not supported -- if not here in the git commit message)

> +/*
> + * Enable status change interrupts
> + *
> + * We don't support status change interrupts, but we need to define  
> this
> + * function otherwise the kernel will panic.
> + */
> +static void qe_uart_enable_ms(struct uart_port *port)
> +{

same question as above.

- k
_______________________________________________
Linuxppc-dev mailing list
[email protected]
https://ozlabs.org/mailman/listinfo/linuxppc-dev

Reply via email to