On Mon, Jun 15, 2020 at 01:56:18PM +0800, Shengjiu Wang wrote:
> For mono channel, SSI will switch to Normal mode.
> 
> In Normal mode and Network mode, the Word Length Control bits
> control the word length divider in clock generator, which is
> different with I2S Master mode (the word length is fixed to
> 32bit), it should be the value of params_width(hw_params).
> 
> The condition "slots == 2" is not good for I2S Master mode,
> because for Network mode and Normal mode, the slots can also
> be 2. Then we need to use (ssi->i2s_net & SSI_SCR_I2S_MODE_MASK)
> to check if it is I2S Master mode.

The fsl_ssi_set_bclk is only called when fsl_ssi_is_i2s_master,
though I agree that that line of comments sounds confusing now.

> So we refine the famula for mono channel, otherwise there

famula => formula?

> will be sound issue for S24_LE.
> 
> Fixes: b0a7043d5c2c ("ASoC: fsl_ssi: Caculate bit clock rate using slot 
> number and width")
> Signed-off-by: Shengjiu Wang <shengjiu.w...@nxp.com>
> ---
> changes in v2
> - refine patch for Network mode and Normal mode.
> 
>  sound/soc/fsl/fsl_ssi.c | 15 +++++++++++----
>  1 file changed, 11 insertions(+), 4 deletions(-)
> 
> diff --git a/sound/soc/fsl/fsl_ssi.c b/sound/soc/fsl/fsl_ssi.c
> index bad89b0d129e..cbf67d132fda 100644
> --- a/sound/soc/fsl/fsl_ssi.c
> +++ b/sound/soc/fsl/fsl_ssi.c
> @@ -678,7 +678,8 @@ static int fsl_ssi_set_bclk(struct snd_pcm_substream 
> *substream,
>       struct regmap *regs = ssi->regs;
>       u32 pm = 999, div2, psr, stccr, mask, afreq, factor, i;
>       unsigned long clkrate, baudrate, tmprate;
> -     unsigned int slots = params_channels(hw_params);
> +     unsigned int channels = params_channels(hw_params);
> +     unsigned int slots;
>       unsigned int slot_width = 32;
>       u64 sub, savesub = 100000;
>       unsigned int freq;
> @@ -688,9 +689,15 @@ static int fsl_ssi_set_bclk(struct snd_pcm_substream 
> *substream,
>       /* Override slots and slot_width if being specifically set... */
>       if (ssi->slots)
>               slots = ssi->slots;
> -     /* ...but keep 32 bits if slots is 2 -- I2S Master mode */
> -     if (ssi->slot_width && slots != 2)
> -             slot_width = ssi->slot_width;
> +     else
> +             /* Apply two slots for mono channel, because DC = 2 */
> +             slots = (channels == 1) ? 2 : channels;
> +
> +     /* ...but keep 32 bits if I2S Master mode */
> +     if ((ssi->i2s_net & SSI_SCR_I2S_MODE_MASK) != SSI_SCR_I2S_MODE_MASTER ||
> +         channels == 1)
> +             slot_width = ssi->slot_width ? ssi->slot_width :

This looks very complicated...can you review and try mine?
(Basically, take 32-bit out of default but force it later)

@@ -678,8 +678,9 @@ static int fsl_ssi_set_bclk(struct snd_pcm_substream 
*substream,
        struct regmap *regs = ssi->regs;
        u32 pm = 999, div2, psr, stccr, mask, afreq, factor, i;
        unsigned long clkrate, baudrate, tmprate;
-       unsigned int slots = params_channels(hw_params);
-       unsigned int slot_width = 32;
+       unsigned int channels = params_channels(hw_params);
+       unsigned int slot_width = params_width(hw_params);
+       unsigned int slots = 2;
        u64 sub, savesub = 100000;
        unsigned int freq;
        bool baudclk_is_used;
@@ -688,10 +689,16 @@ static int fsl_ssi_set_bclk(struct snd_pcm_substream 
*substream,
        /* Override slots and slot_width if being specifically set... */
        if (ssi->slots)
                slots = ssi->slots;
-       /* ...but keep 32 bits if slots is 2 -- I2S Master mode */
-       if (ssi->slot_width && slots != 2)
+       if (ssi->slot_width)
                slot_width = ssi->slot_width;
 
+       /*
+        * ...but force 32 bits for stereo audio. Note that mono audio is also
+        * sent in 2 slots via NORMAL mode, so check both slots and channels.
+        */
+       if (slots == 2 && channels == 2)
+               slot_width = 32;
+
        /* Generate bit clock based on the slot number and slot width */
        freq = slots * slot_width * params_rate(hw_params);
 

Reply via email to