This patch is a workaround for bug #364 found in the MPC52xx processor.
The errata document can be found under
http://www.freescale.com/files/32bit/doc/errata/MPC5200E.pdf?fpsp=1&WT_TYPE=Errata&WT_VENDOR=FREESCALE&WT_FILE_FORMAT=pdf&WT_ASSET=Documentation
When a device with a low baudrate is connected to the serial port, but
the processor "listens" on a higher baudrate, it might falsely receive
breaks from the controller. During a break, the serial controller may
not be reset. The appended patch provides a workaround for that
situation by lowering the baudrate without resetting the controller and
waiting until no break is received anymore.
This is v4 if the patch, just reformatted to fit the linux kernel coding
style without functional changes.
Wolfram Sang schrieb:
Hi René,
On Tue, Nov 04, 2008 at 08:40:09PM +0100, René Bürgel wrote
But there's still one thing, that bothers me a bit - if there is REALLY
a break on the line, closing the driver may take until it's gone. I
don't know whether this is really satisfying, but i think it's better
than the alternative: no serial connection until the next reboot.
I think we should CC linux-serial to get some opinions about this. At
least, if it stays like this, it should be mentioned in the source.
What's the opinion from the linux-serial folks about this issue?
--
René Bürgel
Software Engineer
Unicontrol Systemtechnik GmbH
OT Dittersbach
Sachsenburger Weg 34
09669 Frankenberg
Tel.: 03 72 06/ 88 73 - 19
Fax: 03 72 06/ 88 73 - 60
E-Mail: [EMAIL PROTECTED]
Internet: www.unicontrol.de
Unicontrol Systemtechnik GmbH
Geschäftsführer: Dipl.-Ing. Siegfried Heinze
Sitz der Gesellschaft: Frankenberg
Registergericht: Amtsgericht Chemnitz, HRB 15 475
Wichtiger Hinweis: Diese E-Mail und etwaige Anlagen können Betriebs- und Geschäftsgeheimnisse, dem Anwaltsgeheimnis unterliegende oder sonstige vertrauliche Informationen
enthalten. Sollten Sie diese E-Mail irrtümlich erhalten haben, ist Ihnen der Status dieser E-Mail bekannt. Bitte benachrichtigen Sie uns in diesem Falle sofort durch
Antwort-Mail und löschen Sie diese E-Mail nebst etwaigen Anlagen aus Ihrem System. Ebenso dürfen Sie diese E-Mail oder ihre Anlagen nicht kopieren oder an Dritte
weitergeben. Vielen Dank!
Important Note: This e-mail and any attachments are confidential, may contain trade secrets and may well also be legally privileged or otherwise protected from disclosure.
If you have received it in error, you are on notice of its status. Please notify us immediately by reply e-mail and then delete this e-mail and any attachment from your
system. If you are not the intended recipient please understand that you must not copy this e-mail or any attachments or disclose the contents to any other person. Thank
you.
diff --git a/drivers/serial/mpc52xx_uart.c b/drivers/serial/mpc52xx_uart.c
index 6117d3d..ae539b5 100644
--- a/drivers/serial/mpc52xx_uart.c
+++ b/drivers/serial/mpc52xx_uart.c
@@ -496,6 +496,74 @@ mpc52xx_uart_break_ctl(struct uart_port *port, int ctl)
spin_unlock_irqrestore(&port->lock, flags);
}
+/*
+ * This is a workaround for processor bug #364
+ * described in MPC5200 (L25R) Errata.
+ * The bug is still present in MPC5200B,
+ * but currently not listed in its errata sheet.
+ *
+ * The workaround resets the baudrate to the slowest possible,
+ * waits for a stable state and resets break state repeatedly if necessary.
+ * Optionally it can release the lock while waiting.
+ *
+ * That baudrate is roughly port->uartclk / (1000 * 1000)
+ * The minimum wait time for the first try has to include
+ * the time to wait for stop-bits and a character.
+ * We wait for 2 chars to be sure.
+ * Consecutive waits must just receive one character.
+ */
+
+#ifdef CONFIG_PPC_MPC52xx
+static void reset_errors_and_wait(struct uart_port *port, bool unlock,
+ unsigned long flags, unsigned int delay)
+{
+ struct mpc52xx_psc __iomem *psc = PSC(port);
+ out_8(&psc->command, MPC52xx_PSC_RST_ERR_STAT);
+ if (unlock) {
+ disable_irq(port->irq);
+ spin_unlock_irqrestore(&port->lock, flags);
+ }
+ mdelay(delay);
+ if (unlock) {
+ spin_lock_irqsave(&port->lock, flags);
+ enable_irq(port->irq);
+ }
+}
+#endif
+
+static void mpc52xx_uart_reset_rx(struct uart_port *port, bool unlock,
+ unsigned long flags)
+{
+#ifdef CONFIG_PPC_MPC52xx
+ struct mpc52xx_psc __iomem *psc = PSC(port);
+
+ /*
+ * One character on the serial port may consist of up to 12 bits.
+ * So the time to receive one char is
+ * 12 / (port->uartclk / (1000 * 1000) ) * 1000,
+ * (bits) (MHz -> Hz) (s -> ms)
+ */
+ unsigned int one_char_receive_duration =
+ (12 * 1000) / (port->uartclk / (1000 * 1000));
+
+ /*
+ * CT=0xFFFF sets the serial line to the minimal possible baudrate
+ * (depending on the uartclk).
+ */
+ out_8(&psc->ctur, 0xFF);
+ out_8(&psc->ctlr, 0xFF);
+
+ reset_errors_and_wait(port, unlock, flags,
+ one_char_receive_duration * 2);
+
+ while ((in_be16(&psc->mpc52xx_psc_status)) & MPC52xx_PSC_SR_RB) {
+ reset_errors_and_wait(port, unlock, flags,
+ one_char_receive_duration);
+ }
+#endif
+ out_8(&psc->command, MPC52xx_PSC_RST_RX);
+}
+
static int
mpc52xx_uart_startup(struct uart_port *port)
{
@@ -510,7 +578,7 @@ mpc52xx_uart_startup(struct uart_port *port)
return ret;
/* Reset/activate the port, clear and enable interrupts */
- out_8(&psc->command, MPC52xx_PSC_RST_RX);
+ mpc52xx_uart_reset_rx(port, false, 0);
out_8(&psc->command, MPC52xx_PSC_RST_TX);
out_be32(&psc->sicr, 0); /* UART mode DCD ignored */
@@ -529,7 +597,7 @@ mpc52xx_uart_shutdown(struct uart_port *port)
struct mpc52xx_psc __iomem *psc = PSC(port);
/* Shut down the port. Leave TX active if on a console port */
- out_8(&psc->command, MPC52xx_PSC_RST_RX);
+ mpc52xx_uart_reset_rx(port, false, 0);
if (!uart_console(port))
out_8(&psc->command, MPC52xx_PSC_RST_TX);
@@ -588,9 +656,6 @@ mpc52xx_uart_set_termios(struct uart_port *port, struct
ktermios *new,
/* Get the lock */
spin_lock_irqsave(&port->lock, flags);
- /* Update the per-port timeout */
- uart_update_timeout(port, new->c_cflag, baud);
-
/* Do our best to flush TX & RX, so we don't loose anything */
/* But we don't wait indefinitly ! */
j = 5000000; /* Maximum wait */
@@ -607,9 +672,12 @@ mpc52xx_uart_set_termios(struct uart_port *port, struct
ktermios *new,
"Some chars may have been lost.\n");
/* Reset the TX & RX */
- out_8(&psc->command, MPC52xx_PSC_RST_RX);
+ mpc52xx_uart_reset_rx(port, true, flags);
out_8(&psc->command, MPC52xx_PSC_RST_TX);
+ /* Update the per-port timeout */
+ uart_update_timeout(port, new->c_cflag, baud);
+
/* Send new mode settings */
out_8(&psc->command, MPC52xx_PSC_SEL_MODE_REG_1);
out_8(&psc->mode, mr1);
_______________________________________________
Linuxppc-dev mailing list
Linuxppc-dev@ozlabs.org
https://ozlabs.org/mailman/listinfo/linuxppc-dev
