Hi Stuart, Thanks for the information. gpp access was
resolved. I was successful in building the linux 2.6.11 using the
ltib and able to bring up the MPC8360 EMDS.But, I still face the problem
for linux kernel 2.6.19 and 2.6.20. When I tried using ltib in
the bringing up the board. The MPC 8360 board keeps
rebooting after downloading the image Power PC Kernel Image(uImage) and Power
PC RAMDisk Image(rootfs.ext2.gz.uboot) build by the
"ltib" Please clarrify on the same.Thanks in
advance.Regards,Nanda On Thu, 20 Nov 2008 18:40:36 0000 Stuart
Hughes wroteHi Nanda,This is happening because you don't have access
tohttp://www.bitshrine.org/gpp for some reason.If LTIB needs to download
sources to build a package, it will get themfrom bitshrine.org. Can you check
that you are able to access this URLfrom the command line with wget.Regards,
StuartOn Thu, 2008-11-20
at 18:30 0000, nanda wrote:> Hi All,> Iam forwarding the mail which I
have posted to powerpc linux list> Linuxppc-dev@ozlabs.org>
===================================================> > Iam getting the
below error during the generation of> rootfs.ext2.gz.uboot (Power PC Linux
RAM Disk Image) and uImage (Power> PC Linux Kernel Image) for linux-2.6.20.6
kernel on the power PC MPC> 8360E MDS using ltib tool.> > "Testing
ppp_url connectivity: FAIL, disabling > > Testing gpp_url connectivity:
FAIL, disabling > > No network download connection available"> > I
did the following steps, but Iam unable to generate the>
rootfs.ext2.gz.uboot > > - In the ltib directory > > ./ltib
--configure> > In the configure menu, I specified the following, before
saving the> configs> > - Tool chain as (gcc-3.4.3/glibc-2.3.3)>
> - uboot 1.1.3> > - "Kernel (local linux directory build)" which
refers to the loca
l> directory where linux-2.6.20.6 is placed> > - "Kernel config
file"specified as mpc8360emds_defconfig, which is the> file copied> from
/home/nanda/linux2.6.20.6/arch/powerpc/configs/mpc8360emds_defconfig to the
ltib/config/platform/mpc8360epb directory) > > - Linux Target
Architecture as "powerpc"> > After the above process by saving the
configuration (it started> building kernel and generated uImage) and failed
in the below place> (Refer also the attached build.txt file)> >
================================> > Processing: skell > >
=================== > > Testing ppp_url connectivity: FAIL, disabling
> > Testing gpp_url connectivity: FAIL, disabling > > No network
download connection available> > Started: Thu Nov 20 14:44:45 2008 >
> Ended: Thu Nov 20 14:57:32 2008 > > Elapsed: 767 seconds > >
Build Failed> > =====================================> > I have
attached the
below files for boot and build logs with this> mail, > > 1)
defconfig.dev - default config generated for "./ltib configure"> from
config/platform/mpc8360epb > > 2) build.txt - Error build during "./ltib
configure" output> > 3) mpc8360emds_defconfig - Default config file>
from /home/nanda/linux2.6.20.6/arch/powerpc/configs/ > > The end result
was I could only see the uImage generated without> rootfs.ext2.gz.uboot.
Please clarify on the same > > Thanks in advance,> > Regards,>
> Nanda> _______________________________________________Linuxppc-dev
mailing [EMAIL PROTECTED]://ozlabs.org/mailman/listinfo/linuxppc-dev
_______________________________________________
Linuxppc-dev mailing list
Linuxppc-dev@ozlabs.org
https://ozlabs.org/mailman/listinfo/linuxppc-dev