> cbe_cpufreq has a partial dependency on cbe_cpufreq_pmi, which cannot > be easily expressed in Kconfig. This fixes it by introducing an > extra Kconfig symbol CBE_CPUFREQ_PMI_ENABLE. To make the dependency > clearer, turn PPC_PMI into an automatic symbol. > > Reported-by: Michael Neuling <mi...@neuling.org> > Signed-off-by: Arnd Bergmann <a...@arndb.de>
Acked-by: Michael Neuling <mi...@neuling.org> Arnd, this fixes one of the problems, but not the cbe table issue I reported in the same thread here (sorry I should have stared a new thread): http://ozlabs.org/pipermail/linuxppc-dev/2009-February/068154.html Seems to be a similar problem when CONFIG_CPU_FREQ_TABLE is a module. Mikey > > --- > > This is the best I could come up with. > > --- a/arch/powerpc/platforms/Kconfig > +++ b/arch/powerpc/platforms/Kconfig > @@ -91,15 +91,6 @@ config RTAS_FLASH > tristate "Firmware flash interface" > depends on PPC64 && RTAS_PROC > > -config PPC_PMI > - tristate "Support for PMI" > - depends on PPC_IBM_CELL_BLADE > - help > - PMI (Platform Management Interrupt) is a way to > - communicate with the BMC (Baseboard Management Controller). > - It is used in some IBM Cell blades. > - default m > - > config MMIO_NVRAM > bool > default n > diff --git a/arch/powerpc/platforms/cell/Kconfig b/arch/powerpc/platforms/cel l/Kconfig > index 5cc3279..037f59a 100644 > --- a/arch/powerpc/platforms/cell/Kconfig > +++ b/arch/powerpc/platforms/cell/Kconfig > @@ -98,7 +98,7 @@ config PPC_IBM_CELL_RESETBUTTON > > config PPC_IBM_CELL_POWERBUTTON > tristate "IBM Cell Blade power button" > - depends on PPC_IBM_CELL_BLADE && PPC_PMI && INPUT_EVDEV > + depends on PPC_IBM_CELL_BLADE && INPUT_EVDEV > default y > help > Support Powerbutton on IBM Cell blades. > @@ -118,9 +118,9 @@ config CBE_CPUFREQ > For details, take a look at <file:Documentation/cpu-freq/>. > If you don't have such processor, say N > > -config CBE_CPUFREQ_PMI > - tristate "CBE frequency scaling using PMI interface" > - depends on CBE_CPUFREQ && PPC_PMI && EXPERIMENTAL > +config CBE_CPUFREQ_PMI_ENABLE > + bool "CBE frequency scaling using PMI interface" > + depends on CBE_CPUFREQ && EXPERIMENTAL > default n > help > Select this, if you want to use the PMI interface > @@ -128,6 +128,20 @@ config CBE_CPUFREQ_PMI > processor will not only be able to run at lower speed, > but also at lower core voltage. > > +config CBE_CPUFREQ_PMI > + tristate > + depends on CBE_CPUFREQ_PMI_ENABLE > + default CBE_CPUFREQ > + > +config PPC_PMI > + tristate > + default y > + depends on CBE_CPUFREQ_PMI || PPC_IBM_CELL_POWERBUTTON > + help > + PMI (Platform Management Interrupt) is a way to > + communicate with the BMC (Baseboard Management Controller). > + It is used in some IBM Cell blades. > + > config CBE_CPUFREQ_SPU_GOVERNOR > tristate "CBE frequency scaling based on SPU usage" > depends on SPU_FS && CPU_FREQ > _______________________________________________ Linuxppc-dev mailing list Linuxppc-dev@ozlabs.org https://ozlabs.org/mailman/listinfo/linuxppc-dev
