Some of FSL SoCs like T1040 has new version of UART controller which
can support 64byte FiFo.
To enable 64 byte support, following needs to be done:
-FCR[EN64] needs to be programmed to 1 to enable it.
-Also, when FCR[EN64]==1, RTL bits to be used as below
to define various Receive Trigger Levels:
-FCR[RTL] = 00 1 byte
-FCR[RTL] = 01 16 bytes
-FCR[RTL] = 10 32 bytes
-FCR[RTL] = 11 56 bytes
-tx_loadsz is set to 32-bytes instead of 64-bytes to implement
workaround of errata A-008006 which states that tx_loadsz should
be configured less than Maximum supported fifo bytes
Signed-off-by: Vijay Rai <vijay....@freescale.com>
Signed-off-by: Priyanka Jain <priyanka.j...@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggr...@freescale.com>
---
drivers/tty/serial/8250/8250_core.c | 20 +++++++++++++++++++-
include/uapi/linux/serial_core.h | 3 ++-
include/uapi/linux/serial_reg.h | 3 ++-
3 files changed, 23 insertions(+), 3 deletions(-)
diff --git a/drivers/tty/serial/8250/8250_core.c
b/drivers/tty/serial/8250/8250_core.c
index 11c6685..565748c 100644
--- a/drivers/tty/serial/8250/8250_core.c
+++ b/drivers/tty/serial/8250/8250_core.c
@@ -329,6 +329,14 @@ static const struct serial8250_config uart_config[] = {
.fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
.flags = UART_CAP_FIFO | UART_CAP_AFE,
},
+ [PORT_16550A_FSL64] = {
+ .name = "16550A_FSL64",
+ .fifo_size = 64,
+ .tx_loadsz = 32,
+ .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10 |
+ UART_FCR7_64BYTE,
+ .flags = UART_CAP_FIFO,
+ },
};
/* Uart divisor latch read */
@@ -956,7 +964,17 @@ static void autoconfig_16550a(struct uart_8250_port *up)
up->port.type = PORT_16650;
up->capabilities |= UART_CAP_EFR | UART_CAP_SLEEP;
} else {
- DEBUG_AUTOCONF("Motorola 8xxx DUART ");
+ serial_out(up, UART_LCR, 0);
+ serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO |
+ UART_FCR7_64BYTE);
+ status1 = serial_in(up, UART_IIR) >> 5;
+ serial_out(up, UART_FCR, 0);
+ serial_out(up, UART_LCR, 0);
+
+ if (status1 == 7)
+ up->port.type = PORT_16550A_FSL64;
+ else
+ DEBUG_AUTOCONF("Motorola 8xxx DUART ");
}
serial_out(up, UART_EFR, 0);
return;
diff --git a/include/uapi/linux/serial_core.h b/include/uapi/linux/serial_core.h
index c172180..a3b4491 100644
--- a/include/uapi/linux/serial_core.h
+++ b/include/uapi/linux/serial_core.h
@@ -55,7 +55,8 @@
#define PORT_ALTR_16550_F64 27 /* Altera 16550 UART with 64 FIFOs */
#define PORT_ALTR_16550_F128 28 /* Altera 16550 UART with 128 FIFOs */
#define PORT_RT2880 29 /* Ralink RT2880 internal UART */
-#define PORT_MAX_8250 29 /* max port ID */
+#define PORT_16550A_FSL64 30 /* Freescale 16550 UART with 64 FIFOs */
+#define PORT_MAX_8250 31 /* max port ID */
/*
* ARM specific type numbers. These are not currently guaranteed
diff --git a/include/uapi/linux/serial_reg.h b/include/uapi/linux/serial_reg.h
index 53af3b7..00adb01 100644
--- a/include/uapi/linux/serial_reg.h
+++ b/include/uapi/linux/serial_reg.h
@@ -86,7 +86,8 @@
#define UART_FCR6_T_TRIGGER_8 0x10 /* Mask for transmit trigger set at 8 */
#define UART_FCR6_T_TRIGGER_24 0x20 /* Mask for transmit trigger set at 24 */
#define UART_FCR6_T_TRIGGER_30 0x30 /* Mask for transmit trigger set at 30 */
-#define UART_FCR7_64BYTE 0x20 /* Go into 64 byte mode (TI16C750) */
+#define UART_FCR7_64BYTE 0x20 /* Go into 64 byte mode (TI16C750 and
+ some Freescale UARTs) */
#define UART_FCR_R_TRIG_SHIFT 6
#define UART_FCR_R_TRIG_BITS(x) \
--
1.7.9.5
_______________________________________________
Linuxppc-dev mailing list
Linuxppc-dev@lists.ozlabs.org
https://lists.ozlabs.org/listinfo/linuxppc-dev
