On Thu, 19 Oct 2006 15:31:10 +0300 (EEST)
[EMAIL PROTECTED] wrote:

> If there is a frame buffer console, the cpm_uart_init_portdesc()
> function is never called in the compat mode. Also, the set_lineif()
> method is not called in the compat mode.
> 
for the fbconsole case, I agree we do have  to address it. But not the proposed 
way.
See below.
 

> Signed-off-by: Kalle Pokki <[EMAIL PROTECTED]>
> ---
>   drivers/serial/cpm_uart/cpm_uart.h      |    2 +-
>   drivers/serial/cpm_uart/cpm_uart_core.c |    9 ++++-----
>   drivers/serial/cpm_uart/cpm_uart_cpm1.c |    6 +++++-
>   drivers/serial/cpm_uart/cpm_uart_cpm2.c |    6 +++++-
>   4 files changed, 15 insertions(+), 8 deletions(-)
> 
> diff --git a/drivers/serial/cpm_uart/cpm_uart.h
> b/drivers/serial/cpm_uart/cpm_uart.h index 3b35cb7..19a6ffe 100644
> --- a/drivers/serial/cpm_uart/cpm_uart.h
> +++ b/drivers/serial/cpm_uart/cpm_uart.h
> @@ -89,7 +89,7 @@ extern struct uart_cpm_port cpm_uart_por
> 
>   /* these are located in their respective files */
>   void cpm_line_cr_cmd(int line, int cmd);
> -int cpm_uart_init_portdesc(void);
> +int __init cpm_uart_init_portdesc(void);
>   int cpm_uart_allocbuf(struct uart_cpm_port *pinfo, unsigned int
> is_con); void cpm_uart_freebuf(struct uart_cpm_port *pinfo);
> 
> diff --git a/drivers/serial/cpm_uart/cpm_uart_core.c
> b/drivers/serial/cpm_uart/cpm_uart_core.c index 8f3b3e5..895f2f1
> 100644 --- a/drivers/serial/cpm_uart/cpm_uart_core.c
> +++ b/drivers/serial/cpm_uart/cpm_uart_core.c
> @@ -1349,11 +1349,8 @@ static int cpm_uart_init(void) {
>               pr_info("cpm_uart: WARNING: no UART devices found
> on platform bus!\n"); pr_info(
>               "cpm_uart: the driver will guess configuration, but
> this mode is no longer supported.\n"); -#ifndef
> CONFIG_SERIAL_CPM_CONSOLE
> -             ret = cpm_uart_init_portdesc();
> -             if (ret)
> -                     return ret;
> -#endif
> +
> +             cpm_uart_init_portdesc();
> 
And we end up with init_portdesc called unconditionally? this would likely 
break, or at least confuse the
code, that uses platform dev to pass resources offsets.

>               cpm_reg.nr = cpm_uart_nr;
>               ret = uart_register_driver(&cpm_reg);
> @@ -1365,6 +1362,8 @@ #endif
>                       int con = cpm_uart_port_map[i];
>                       cpm_uart_ports[con].port.line = i;
>                       cpm_uart_ports[con].port.flags =
> UPF_BOOT_AUTOCONF;
> +                     if (cpm_uart_ports[con].set_lineif)
> +
> cpm_uart_ports[con].set_lineif(&cpm_uart_ports[con]);
> uart_add_one_port(&cpm_reg, &cpm_uart_ports[con].port); }
> 
> diff --git a/drivers/serial/cpm_uart/cpm_uart_cpm1.c
> b/drivers/serial/cpm_uart/cpm_uart_cpm1.c index 95afc37..6f04a9f
> 100644 --- a/drivers/serial/cpm_uart/cpm_uart_cpm1.c
> +++ b/drivers/serial/cpm_uart/cpm_uart_cpm1.c
> @@ -184,10 +184,14 @@ void cpm_uart_freebuf(struct uart_cpm_po
>   }
> 
>   /* Setup any dynamic params in the uart desc */
> -int cpm_uart_init_portdesc(void)
> +int __init cpm_uart_init_portdesc(void)
>   {
>       pr_debug("CPM uart[-]:init portdesc\n");
> 
> +     /* Don't run this again, if the console driver did it
> already */
> +     if (cpm_uart_nr > 0)
> +             return 0;
> +
>       cpm_uart_nr = 0;
>   #ifdef CONFIG_SERIAL_CPM_SMC1
>       cpm_uart_ports[UART_SMC1].smcp = &cpmp->cp_smc[0];
> diff --git a/drivers/serial/cpm_uart/cpm_uart_cpm2.c
> b/drivers/serial/cpm_uart/cpm_uart_cpm2.c index ef3bb47..0f21543
> 100644 --- a/drivers/serial/cpm_uart/cpm_uart_cpm2.c
> +++ b/drivers/serial/cpm_uart/cpm_uart_cpm2.c
> @@ -252,10 +252,14 @@ void cpm_uart_freebuf(struct uart_cpm_po
>   }
> 
>   /* Setup any dynamic params in the uart desc */
> -int cpm_uart_init_portdesc(void)
> +int __init cpm_uart_init_portdesc(void)
>   {
>       pr_debug("CPM uart[-]:init portdesc\n");
> 
> +     /* Don't run this again, if the console driver did it
> already */
> +     if (cpm_uart_nr > 0)
> +             return 0;
> +

Personally, I don't care much of compat stuff, unless it is breaking/confusing 
targets 
using proper resources...

>       cpm_uart_nr = 0;
>   #ifdef CONFIG_SERIAL_CPM_SMC1
>       cpm_uart_ports[UART_SMC1].smcp = (smc_t *) &
> cpm2_immr->im_smc[0];

Attachment: signature.asc
Description: PGP signature

_______________________________________________
Linuxppc-embedded mailing list
[email protected]
https://ozlabs.org/mailman/listinfo/linuxppc-embedded

Reply via email to