Hi, you could use a Kontron E2Brain EB8347 Eval-Board instead of the rattler board. It comes with a BSP with a Kernel 2.6.13 including USB 2.0 support. I have already tested this port against keyboards, mice, touch controllers and memory sticks.
Soon, a Freescale Kernel 2.6.17 with flattened device tree support and the appropriate Bootloader for this board will be available (i have running it in my office since some months on this platform). This will additionally provide the USB transaction handler for USB 1.1 / USB 2.0 autonegotiation/switching. -- Mit freundlichen Gruessen / Best regards Claus Gindhart SW R&D Kontron Modular Computers phone :++49 (0)8341-803-374 mailto:[EMAIL PROTECTED] http://www.kontron.com -----BEGIN GEEK CODE BLOCK----- Version: 3.1 GU d- s++:>++:+ a+ C++$ !U !P L++>$ E-- W+(-) N- o? K? w !O !M V !PS PE- Y+ PGP+ t 5? X R* tv- b+ DI+++ D-- G e++> h--- !r x+++ ------END GEEK CODE BLOCK------ -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Jamie Guinan Sent: Freitag, 1. Dezember 2006 07:54 To: Li Yang-r58472 Cc: linuxppc-embedded@ozlabs.org Subject: RE: Rattler 8347 and USB 2.0 On Fri, 1 Sep 2006, Li Yang-r58472 wrote: > > -----Original Message----- > > From: > > [EMAIL PROTECTED] > > [mailto:[EMAIL PROTECTED] > > rg] On Behalf Of Jamie Guinan > > Sent: Friday, September 01, 2006 12:14 AM > > To: linuxppc-embedded@ozlabs.org > > Subject: Rattler 8347 and USB 2.0 > > > > > > Greetings, > > > > I have an mpc8347 board here (A&M Rattler 8347). It shipped with a > > 2.6.16 patched enough to boot the board, but support for > > freescale USB 2.0 (ehci) is not present. > > > > Working my way backwards in the mainline kernel tree > > (2.6.18-rc5), I found drivers/usb/host/ehci-fsl.c, for > > FreeScale/PPC EHCI support. > > > > In that module, usb_hcd_fsl_probe() requires an initialized > > "struct fsl_usb2_platform_data", which only appears in > > arch/powerpc/sysdev/fsl_soc.c, yet the 2.6.16 patch provided > > puts the board in arch/ppc. > > > > My question is, what would be the best way to go about > > getting ehci-fsl.c working with this board? > > > > 1) Nudge the Rattler port from arch/ppc to arch/powerpc. One > > problem with this is that the rattler uses RedBoot, and reading this, > > > > http://ozlabs.org/pipermail/linuxppc-embedded/2006-August/024116.html > > > > it looks like arch/powerpc wants to boot from > > OpenFirmware-like "flattened device tree" (does RedBoot > > support this?). > > Use a shim which directly builds FDT in kernel to use powerpc arch. > > > > 2) Support ehci-fsl.c from arch/ppc. If arch/ppc is > > deprecated, that's a bad long-term solution. And since > > fsl_soc.c lives under arch/powerpc, that doesn't look good either. > > Actually you don't need fsl_soc.c in ppc arch. There are predefined > platform_device and platform_data in arch/ppc/syslib/mpc83xx_devices.c. > You can add your usb platform_data there easily. So I got back on this (months later), and I added that entry like you suggested (below is against 2.6.17, for reference only, do not apply), <patch> --- mpc83xx_devices.c.ori 2006-11-30 01:09:19.000000000 -0500 +++ mpc83xx_devices.c 2006-11-30 01:49:46.000000000 -0500 @@ -64,6 +64,12 @@ { }, }; +static struct fsl_usb2_platform_data mpc83xx_usb_platform_data = { + .operating_mode = FSL_USB2_MPH_HOST, + .phy_mode = FSL_USB2_PHY_ULPI, + .port_enables = FSL_USB2_PORT0_ENABLED | FSL_USB2_PORT1_ENABLED, +}; + struct platform_device ppc_sys_platform_devices[] = { [MPC83xx_TSEC1] = { .name = "fsl-gianfar", @@ -205,6 +211,7 @@ [MPC83xx_USB2_MPH] = { .name = "fsl-usb2-mph", .id = 1, + .dev.platform_data = &mpc83xx_usb_platform_data, .num_resources = 2, .resource = (struct resource[]) { { </patch> and I was quite pleased to see this on my console on the next boot, fsl-usb2-mph fsl-usb2-mph.1: Freescale On-Chip EHCI Host Controller fsl-usb2-mph fsl-usb2-mph.1: new USB bus registered, assigned bus number 1 fsl-usb2-mph fsl-usb2-mph.1: irq 39, io base 0xff022000 fsl-usb2-mph fsl-usb2-mph.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: Product: Freescale On-Chip EHCI Host Controller usb usb1: Manufacturer: Linux 2.6.17-1_AM_JSG_NOV29 ehci_hcd usb usb1: SerialNumber: fsl-usb2-mph.1 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected Initializing USB Mass Storage driver... Thanks for that tip. Next (hopefully minor) hurdle is that I'm not seeing any activity when I plug in a device, and the ehci irq39 line in /proc/interrupts stays at 0. Some of the PHY signals go through an FPGA on this board, I'm talking to my vendor about that. -Jamie _______________________________________________ Linuxppc-embedded mailing list Linuxppc-embedded@ozlabs.org https://ozlabs.org/mailman/listinfo/linuxppc-embedded _______________________________________________ Linuxppc-embedded mailing list Linuxppc-embedded@ozlabs.org https://ozlabs.org/mailman/listinfo/linuxppc-embedded